Difference between revisions of "Lisa/M v2.0"

Revision as of 18:17, 15 March 2012

Lisa/M is a small, general purpose autopilot designed with flexibility across multiple applications in mind. Small weight and size, with (optional) integrated Aspirin IMU and full size 0.1" servo headers make the Lisa/M suitable for both fixed-wing and rotorcraft vehicles. This autopilot is based on the STM32 for improved peripherals and faster processing.

A number of tutorials are being prepared for getting started with Lisa/M:

Hardware Revision History

Version #	Release Date	Release Notes
v2.0(current)	03/2012	Updated Production Release
v1.1	MM/YYYY	Updated Prototype
v1.0	MM/YYYY	Initial Production Release
v0.1	MM/YYYY	Initial prototype of Lisa/M

For detailed hardware revision history, please see below.

Features

Lisa/M is based on the 64 pins STM32F105RCT6 connectivity line family processor featuring 64k of RAM and 256k of FLASH. All the pins are exposed, providing access to the complete set of the STM32 peripherals. NOTE: This MCU is different from LISA/L. Lisa/L is based on the 64 pins STM32F103RE processor featuring 64k of RAM and 512k of FLASH, which is part of the high-density performance line family.

STM32 microcontroller STM32F105RCT6 datasheet with 256kB flash and 64kB RAM
Pressure sensor BMP085
7 x Analog input channels
3 x Generic digital in-/out-puts
2 x 3.3V TTL UART (5V tolerant)
8 x Servo PPM outputs (6 w/ second I2C bus in use)
1 x CAN bus
1 x SPI bus
1 x I²C bus (2 when using only 6 Servo PPM outputs)
1 x Micro USB
4 x status LEDs with attached test point
10.8 grams (0.4 oz) (with Aspirin IMU mounted)
9.9 grams (0.35 oz) (without Aspirin IMU mounted)
~34mm x ~60mm x ~10mm
4 layers PCB design

with mounted IMU has the following additional sensors on board:

3 Axis Gyroscope
3 Axis Accelerometer
3 Axis Magnetometer

The pressure sensor is mounted directly on the board as this sensor is not provided by Aspirin (v0.1 - v1.1). Except for a GPS unit you have all necessary sensors for full attitude and altitude stabilization in an extremely small package.

Lisa/M V2.0 top view
Lisa/M V2.0 bottom view

Pinout

Pins Name and Type are specified with respect to the Autopilot Board.

**SERVO1/2/3/4/5/6/7/8**
Pin #	Name	Type	Description	Color
1	SERVOx	OUT	Servo signal (PWM)(See Note 1 below)	Yellow
2	SV	PWR	Servo Bus Voltage Rail (conf w/ JP1)	Red
3	GND	PWR	common ground	Black

**JTAG**
Pin #	Name	Type	Description	Color
1	N/A	N/A	JTAG Debug Header (Pin 1 is +3V3)	None

**UART3**
Pin #	Name	Type	Description	Color
1	GND	PWR	common ground	Black
2	+5V	PWR	UART Voltage (conf w/ JP6 and JP7)	Red
3	TX	OUT	USART3 Serial Output (3.3V level)	Yellow
4	RX	IN	USART3 Serial Input (3.3V level)(Pullup to Pin 2 voltage)(5V tolerant)	Orange

**UART1/5**
Pin #	Name	Type	Description	Color
1	GND	PWR	common ground	Black
2	+3V3	PWR	3.3V Rail from autopilot (conf w/ JP8 and JP9)	Red
3	RX1	IN	USART1 Serial Input (3.3V level)(Pullup to Pin 2 voltage)(5V tolerant)	Orange
4	GND	PWR	common ground	Black
5	+3V3	PWR	3.3V Rail from autopilot (conf w/ JP8 and JP9)	Red
6	RX5	IN	UART5 Serial Input (3.3V level)(Pullup to Pin 5 voltage)(5V tolerant)	Orange

**GPIO**
Pin #	Name	Type	Description	Color
1	GND	PWR	common ground	Black
2	+3V3	PWR	3.3V Rail from autopilot	Red
4	PC12	I/O	GPIO, connected to PC12 (5V tolerant)	Dark Tan
5	TRST	I/O	JTAG_TRST (also connected to LED1 cathode)	Light Tan

**ANALOG1**
Pin #	Name	Type	Description	Color
1	GND	PWR	common ground	Black
2	+3V3	PWR	3.3V Rail from autopilot	Red
3	+5V	PWR	5V Rail from autopilot	Red
4	ADC4	I/O	ADC4, by default connected to LED7 cathode (Remove LED/resistor to use as ADC)	Magenta
5	ADC6	I/O	ADC6, by default connected to LED8 cathode (Remove LED/resistor to use as ADC)	Pink
6	BOOT0	I/O	BOOT0	Grey

**USB**
Pin #	Name	Type	Description	Color
1	N/A	N/A	USB (The USB connections are also available as 0.05" (1.27mm) through hole pads underneath the GPIO header)	None

**I2C1 CAN**
Pin #	Name	Type	Description	Color
1	GND	PWR	common ground	Black
2	V_BATT	PWR	V_BAT Bus on autopilot, voltage divider for V_BAT_MEAS, (conf w/ JP2 to connect to V_IN)	Red
3	V_IN	PWR	Connected to autopilot voltage regulator inputs (conf w/ JP1, JP2 and JP3)	Red
4	CANL	I/O	CANL (5V level)	Orange
5	CANH	I/O	CANH (5V level)	Yellow
6	SCL	I/O	SCL (5V level)(See Note 1 below)	Green
7	SDA	I/O	SDA (5V level)(See Note 1 below)	Blue

**SPI1**
Pin #	Name	Type	Description	Color
1	GND	PWR	common ground	Black
2	+3V3	PWR	3.3V Rail from autopilot	Red
3	MOSI	Out	MOSI	Orange
4	MISO	In	MISO	Yellow
5	SCK	Out	SCK	Green
6	SS	Out	SS	Blue
7	DRDY	I/O	DRDY	Dark Tan

**ANALOG2**
Pin #	Name	Type	Description	Color
1	GND	PWR	common ground	Black
2	+3V3	PWR	3.3V Rail from autopilot	Red
3	+5V	PWR	5V Rail from autopilot	Red
4	ADC1	In	ADC1	Green
5	ADC2	In	ADC2	Blue
6	ADC3	In	ADC3	Light Tan

**UART2**
Pin #	Name	Type	Description	Color
1	GND	PWR	common ground	Black
2	+3V3	PWR	UART Voltage (conf w/ JP4 and JP5)	Red
3	TX	OUT	USART2 Serial Output (3.3V level)	Yellow
4	RX	IN	USART2 Serial Input (3.3V level)(NOT 5V TOLERANT)(Pullup to Pin 2 voltage)	Orange

**I2C2**
Pin #	Name	Type	Description	Color
1	GND	PWR	common ground	Black
2	+3V3	PWR	3.3V Rail from autopilot	Red
3	SCL	I/O	SCL (3.3V level)	Green
4	SDA	I/O	SDA (3.3V level)	Blue

NOTE 1: SERVO7 and SERVO8 are directly connected to I2C1_SCL and I2C1_SDA. As such, SERVO7 and SERVO8 CAN NOT be used while I2C1 is being used.

Jumper Configuration

There are a number of jumpers on Lisa/M used to configure voltage levels and power input.

The default configuration is all UART header VCC pins at +3V3, with the V_SERVO servo voltage rail connected to the autopilot V_IN rail, allowing one to power the autopilot from the servo power. The +5V regulator is NOT bypassed, allowing a regulated +5V on listed headers and for the CAN transceiver and I2C level shifter. The V_BAT connector is NOT connected to V_IN, so one can attach a battery voltage to the V_BAT pin to measure the battery voltage, if so desired.

Lisa/M v2.0 Top Jumpers and LEDs
Lisa/M v2.0 Bottom Jumpers

**Power Jumper Configuration**
Jumper	Bus Connection	Default	Description
JP1	SERVO_BUS to V_IN	CLOSED	Connects servo header voltage rail SERVO_BUS to autopilot input voltage V_IN rail
JP2	V_BAT to V_IN	OPEN	Connects I2C1/CAN rail V_BAT to autopilot input voltage V_IN rail
JP3	V_IN to +5V	OPEN	Connects autopilot input voltage V_IN rail to autopilot +5V rail, bypassing onboard 5V supply

**UART3 VCC Configuration**
Jumper	Bus Connection	Default	Description
JP6	UART3_VCC to V_IN	CLOSED	Connects UART3 connector VCC to autopilot input voltage V_IN rail
JP7	UART3_VCC to +3V3	OPEN	Connects UART3 connector VCC to autopilot +3V3 rail

WARNING: UART3 GPS Connector is connected to V_IN, check your GPS input voltage before connecting!!!

WARNING: DO NOT CLOSE BOTH JP6 AND JP7 SIMULTANEOUSLY!!!

**UART2 VCC Configuration**
Jumper	Bus Connection	Default	Description
JP4	UART2_VCC to V_IN	OPEN	Connects UART2 connector VCC to autopilot input voltage V_IN rail SEE WARNING BELOW
JP5	UART2_VCC to +3V3	CLOSED	Connects UART2 connector VCC to autopilot +3V3 rail

WARNING: UART2 RX is NOT 5V TOLERANT. Thus, while possible to connect UART2_VCC to V_IN, DO NOT ATTEMPT THIS. Only use JP5 (the default).

WARNING: DO NOT CLOSE BOTH JP4 AND JP5 SIMULTANEOUSLY!!!

**UART1 and UART5 VCC Configuration**
Jumper	Bus Connection	Default	Description
JP8	UART1&5_VCC to V_IN	OPEN	Connects UART1 and UART5 connector VCC to autopilot input voltage V_IN rail
JP9	UART1&5_VCC to +3V3	CLOSED	Connects UART1 and UART5 connector VCC to autopilot +3V3 rail

WARNING: DO NOT CLOSE BOTH JP8 AND JP9 SIMULTANEOUSLY!!!

There are additional jumpers on the board for expert or developer configurations, please see schematic and layout for more information.

Powering the Board

The 3.3V regulator on Lisa/M is a MIC5209-3.3YM capable of delivering up to 500mA. While it is possible to power this regulator with up to 16V, experience has shown that this regulator can become very hot in operation with high input voltages, resulting in potential thermal shutdown while in flight. Depending on the expected current draw, it is best to power this regulator with a lower voltage. 5V is the perfect choice. Note that the UART3 GPS Connector is connected to V_IN, check your GPS input voltage before connecting.

The onboard 5V regulator on Lisa/M is a LP2992, a low-noise, low-dropout linear regulator capable of delivering up to 250mA. This regulator can be bypassed with JP3, connecting the autopilot V_IN bus directly to the autopilot 5V bus if, for example, one is using an external 5V regulated supply.

When measuring the supply voltage of a battery with the V_BAT pin (could be connected to V_IN through JP2), it is important to note the maximum voltage limit. The voltage divider on the board for measuring with a 3.3V ADC is --V_BAT--/\/\10k/\/\--V_BAT_MEAS--/\/\2k2/\/\--GND--. This means that the maximum allowable voltage on V_BAT is VBAT_max = 3.3*10k/2.2k = 15V. If a higher voltage measurement is desired, another voltage divider is required off-board. Alternatively, one could modify the existing voltage divider (e.g. change 10k resistor to 22k to get 33V maximum). When checking if voltage exceeds the maximum, make sure to consider maximum battery voltage, not nominal voltage (e.g. 4.22V or so for a single lithium cell, not 3.7V nominal).

Schematic

LisaM V2.0 Schematic Sheet 1/3
LisaM V2.0 Schematic Sheet 2/3
LisaM V2.0 Schematic Sheet 3/3

Examples of Airborne Equipment Electrical Connections

Small Aircraft Connection Diagram

Need an Umarim_v1.0-style ( here) small aircraft airborne equipment electrical connections here.

Large Aircraft Connection Diagram

Need an Umarim V1.0-style ( here) large aircraft airborne equipment electrical connections diagram here.

R/C Receivers

There is Spektrum parser available already, enabling the direct use of 1 or 2 Spektrum satellite receivers.

Also UART pins can be used as general purpose I/O to be used for PPM input. Additionally PPM encoder can be used to avoid receiver hardware modification.

PCB

Gerber & Drill Files

Download Lisa/M v2.0 gerber & drill files (zip) NOT YET AVAILABLE BUT SEE Downloads Need some generated gerbers and drill files here.

Assembly

Components Layout

NOT YET AVAILABLE BUT SEE Downloads Need some top and bottom of board images and line drawings here.

Bill Of Material

Download Lisa/M v2.0 Bill Of Material (zipped .xls file) NOT YET AVAILABLE BUT SEE Downloads

PCB and assembled boards suppliers

Available on Get Hardware page, hopefully :)

Mechanical Dimensions

The overall height of the board including the servo connectors is 10mm. Note that the overall length includes the USB connector. The mounting holes are nominal 2mm diameter (with a bit of clearance).

Downloads

Source files

download available on GitHub: Lisa/M v2.0 Cadsoft Eagle 6 Design

Gerber & Drill files

download NOT YET AVAILABLE Need generated gerbers and drill files

Assembly files

download NOT YET AVAILABLE Need Lisa/M v2.0 Components layouts (pdf)
download NOT YET AVAILABLE Need Lisa/M v2.0 Bill Of Material

Paparazzi USB Bootloader Upload

There is currently not a bootloader for STM32-based autopilots. Work is underway to remedy this, see Luftboot on GitHub. Right now, one must use JTAG to load firmware to the board.

Required components

Connection Diagram

Boot Sequence

JTAG

JTAG can be used to upload firmware if no bootloader as present. It can also be used for debugging.

JTAG description;
General debugging information;
JTAG usage, includes Eclipse uplink tutorial.

Detailed Hardware Revision History

Changes Between v1.1 and v2.0

Lot's of silkscreen improvements
Added attributes to all parts to make the usage of bom-ex ulp possible.
Improved routing to allow teardropping
Fixed stm32f1, f2 and f4 compatibility circuit. (has to jump to ground not to 3v3)
Connected existing UART RX pullups to the respective connector power pins instead of 3v3. To prevent connecting 5V over IO pin to the 3v3 power rail.
Added pullups on all UART RX lines to prevent undesired floatation.
LED's are connected to 3v3 now. To make sure we don't have an issue with voltage tolerance on the gpio pins.
...

Changes Between v1.0 and v1.1

Removed pull-ups on the USB gpio
Removed pull-ups on the CAN gpio
Connected usb_vbus to pa9 (needed by the USBotg)
Removed USB pullup transistor as usbotg has a built in pullup
Swapped UART1 with UART3 (uart1 was used for gps and pa9 was it's tx line, to be able to talk to the gps unit uart3 is a better choice, as uart1 only has an rx line now it is a better choice for spektrum RX modules)
Removed USART3 TX gpio from the GPIO connector and moved to the GPS connector
Added voltage selector jumpers to the RC RX connector; to enable powering of 3v3 or an 5v receivers
Replaced vertical board solution with through hole servo pin headers (easier assembly)
Servo connectors are in groups of two; for easier assembly
Servo VBUS is connected together on all four layers; for lower resistance
Moved LED's from under the analog2 connector; to be able to populate LED's and the connector
Moved the RC RX connector a bit; to prevent crashing with the jtag plug
Added one additional servo connector; now we have all 8 accessible through the standard servo connectors
Fixed servo channel labeling to start at S0 as it is the case on TWOG and Tiny autopilot boards
Added secondary through hole picoblade USB connector for easier routing of USB inside an airframe
...

Changes Between v0.1 and v1.0

Switched to stm32f105 to be able to use usb and can at the same time
Added alternative use of the adc lines as led output
...

Hardware Change Requests

REQ: Replace BMP085 with MS5611 (the MS5611 seems to be better in performance then the BMP but it is more expensive and seems to be more difficult to obtain.
- A: This upgrade will be available through Aspirin v2.0 --Esden 22:54, 5 January 2012 (CET)

REQ: Replace 7 Pin CAN with molex with something less risky to be inserted in 7 Pin SPI in relation to powering the board via CAN molex.

REQ: Separate spot for external power if powered via separate battery. Realizing we can via Servo ports by Bridge J1 but still like to measure board voltage then and have a way to add power without mistakenly inject CAN Molex into SPI.

@@ Line 243: / Line 243: @@
 |}
-NOTE 1: SERVO7 and SERVO8 are directly connected to I2C1_SCL and I2C1_SDA. As such, SERVO7 and SERVO8 '''CAN NOT''' be used while I2C1 is being used.
+'''NOTE 1''': SERVO7 and SERVO8 are directly connected to I2C1_SCL and I2C1_SDA. As such, SERVO7 and SERVO8 '''CAN NOT''' be used while I2C1 is being used.
@@ Line 318: / Line 319: @@
 == Schematic ==
-<gallery widths=200px heights=200px>
+<gallery widths=250px heights=168px>
 Image:Lisa_m_v2_0_sheet_1.png | LisaM V2.0 Schematic Sheet 1/3
 Image:Lisa_m_v2_0_sheet_2.png | LisaM V2.0 Schematic Sheet 2/3

Difference between revisions of "Lisa/M v2.0"

Revision as of 18:17, 15 March 2012

Contents

Hardware Revision History

Features