Apogee/v1.00

Autopilots Booz HB Autopilots Lisa Tiny YAPA Autopilots Ap.parrot minidrone Apogee/v1.00 HITL Autopilots Bebop Booz Chimera/v1.00 Classix CrazybeeF4Pro Disco Elle Elle0 Future Autopilots Krooz KroozSD LinAM V4 Lisa Lisa/Bone Lisa/L Lisa/M Lisa/M v1.0 Lisa/M v2.0 Lisa/MX Lisa/S NavGo v3 NavStik Pixhawk Pixracer Previous Autopilots STM32F4 Discovery STM32F429I Discovery Tawaki/v1.00 Tawaki/v1.10 Tawaki/v2.01 TWOG/v1.0 Umarim Lite v2 Umarim v1.0 Xvert

Overview

• STMicroelectronics STM32F405RGT6 Cortex M4 168MHz processor featuring a Floating point unit (FPU), up to 192k of RAM and 1024k of FLASH.
• 9(6) DOF integrated IMU MPU-9150(6050) based
• 1 x Barometer/altimeter MPL3115A2 (I2C, MPU slave capability)
• 1 x MicroSD card slot, 4 bit SDIO interface (high speed data logging)
• 1 x USB : DFU mode (download) or USB storage (direct access to MicroSD card)
• 6 x Servo PWM outputs
• 1 x R/C receiver PPM frame input
• 1 x R/C receiver serial input with inverter (Futaba S.BUS, Spektrum, etc.)
• 3 x UART
• 2 x I²C bus
• 1 x SPI bus
• RTC with backup capacitor
• SWD(ARM download/debug interface)
• 4 x Auxiliary I/O (General Purpose and/or ADC and/or servo PWM)
• 5v / 1.5A switching power supply (input voltage range 5.5V min → 17.0v max)
• 3.3v / 1A linear regulator
• 1 x 5v / 500mA power switch
• 4 x status LEDs
• 10.4 grams (0.37 oz)
• 53 x 25mm (2.1" x 0.98"), shares the same external dimensions and mounting points as UmarimLite
• 4 layers PCB design

Hardware Revision History

Version #	Release Date	Release Notes
v1.00	07/2013	Initial release of Apogee

Detailed Features

SDIO (MicroSD card)

• software support available with v5.2 and above
• hi-cap power designed to give enough time to cleanly save buffer and close file(s) when power outage detected
• USB-storage mode when plugging an USB cable after startup

6 or 9 DOF IMU

Apogee v1.00 PCB offer two Invensense IMU chip options:

• MPU-6050 : 6 DOF, 3 axis Accelerometer + 3 axis Gyroscope
• MPU-9150 : 9 DOF, 3 axis Accelerometer + 3 axis Gyroscope + 3 axis Magnetometer

USB Modes

• usb plugged before autopilot is powered : enter DFU mode to be flashed
• usb plugged after autopilot is powered : stop ap task, enter usb storage mode to made sdcard content easily avalaible, after the host has mounted;copied;dismounted storage;unplugged usb, ap restart

SWD: Serial Wire Debug

permits flash and source level debugging via swd part of cheap discovery card, or via more capable, fastest, more expensive probe like black magic probe

R/C Serial

In addition to the classic PPM input, that mostly require receiver modification, one pin of the R/C connector is routed to the MCU UART2 receive input through a controlled inverter.
This new feature allow direct connection (3 pin) of several brand off-the-shelf receivers without hardware modification or external encoder board.

• RX2_POL(PB13) = 0 => R/C serial (Rx2) is non-inverted : allow use standard polarity serial receivers (Spektrum, FlyElectric...)
• RX2_POL(PB13) = 1 => R/C serial (Rx2) is inverted : allow use of S.BUS protocol compatible receivers (Futaba, FrSky,...)

(see R/C Receivers and Radios page for serial compatible receiver)

Real Time Clock

supercap powered rtc, permit to associate correct time and date on sdcard log files, when ap is unpowered between flights

Power Switch

5V power output pin on AUX connector ("5Vaux",#2) can be switched ON and OFF on demand using APSW (MCU GPIO output PB12).

• APSW = 0 => 5V Aux OFF
• APSW = 1 => 5V Aux ON (default)

The internal switch TPS2051B is designed to withstand 500mA continuous current and is short-circuit and thermally protected.
(see TPS2051B datasheet for recommended operation conditions)

Pictures

• 

  Apogee v1.00 3D bottom view

• 

  Apogee v1.00 3D top view

• 

  Apogee v1.00 bottom view

• 

  Apogee v1.00 top view

• 

  Apogee v1.00 and Umarim-Lite
  footprint comparison

Pinout

Pins Name and Type are specified with respect to the Autopilot Board

SRV0/1/2/3/4/5

Pin #	Name	Type	Description
1	GND	PWR	common ground
2	+5V	PWR	5V Rail from autopilot
3	SRVx	OUT	Servo signal (PWM)

R/C

Pin #	Name	Type	Description
1	GND	PWR	common ground
2	+5v	PWR	5V Rail from autopilot
3	PPM in	IN	PPM Stream from R/C Receiver (5V tolerant)
4	RX2	IN	UART2 Serial Input (5V Tolerant) through controlled inverter

UART1/4/6

Pin #	Name	Type	Description
1	GND	PWR	common ground
2	+5V	PWR	5V Rail from autopilot
3	+3.3V	PWR	3.3V Rail from autopilot
4	RX1/4/6	IN	UART1/4/6 Serial Input (3.3V level, UART1 and UART6 are 5V tolerant, UART4 IS *NOT* 5V tolerant)
5	TX1/4/6	OUT	UART1/4/6 Serial Output (3.3V level)

I2C1/2

Pin #	Name	Type	Description
1	GND	PWR	common ground
2	+5V	PWR	5V Rail from autopilot
3	+3.3V	PWR	3.3V Rail from autopilot
4	SDA1/2	Open Drain I/O (1.5k pull-up)	I2C1/2 bus Serial DAta
5	SCL1/2	Open Drain I/O (1.5k pull-up)	I2C1/2 bus Serial CLock

USB

Pin #	Name	Type	Description
1	GND	PWR	common ground
2	USB+	I/O	USB bidirectional D+ line
3	USB-	I/O	USB bidirectional D- line
4	VBUS	IN	Indicates the presence of USB bus power (5V level), DFU or USB storage Mode selection

Note: MiniUSB and Molex USB connectors are in parallel, only one can be connected at a time.

SPI1

Pin #	Name	Type	Description
1	GND	PWR	common ground
2	+5V	PWR	5V Rail from autopilot
3	+3.3V	PWR	3.3V Rail from autopilot
4	CS1	OUT	Slave Select. Selects the SPI slave (PB9)
5	MOSI1	I/O	SPI1 Master Out Slave In. Data output from master / data input to slave
6	MISO1	I/O	SPI1 Master In Slave Out. Data input to master / data output from slave
7	SCK1	I/O	SPI1 Serial clock. Clock output from master or input to slave

AUX

Pin #	Name	Type	Port	Description
1	GND	PWR		common ground
2	+5Vaux	PWR		5V from autopilot through Power Switch
3	+3.3V	PWR		3.3V Rail from autopilot
4	AUX1	I/O	PB1	General Purpose I/O #1 or ADC_1 Input or PWM6
5	AUX2	I/O	PC5	General Purpose I/O #2 or ADC_2 Input
6	AUX3	I/O	PC4	General Purpose I/O #3 or ADC_3 Input
7	AUX4	I/O	PB15	General Purpose I/O #4 (also spektrum bind pin)

SWD

Pin #	Name	Type	Description
1	GND	PWR	common ground
2	+3.3V	PWR	3.3V Rail from autopilot
3	RST	IN	MCU Reset
4	SWCLK	IN	Serial Wire Clock
5	SWDIO	I/O	Serial Wire Data Input/Output

Schematic

PCB

Gerber & Drill Files

PCB design Eurocircuits 6-C class compliant:

Download Apogee v1.00 gerber & drill files (zip)

RS274X, units = Inches, format = 2:5

• Apogee_v100_Silkscreen_TOP.GBR (Top Component Print Layer)
• Apogee_v100_Soldermask_Top.GBR (Top Solder Mask)
• Apogee_v100_Paste_Mask_Top.GBR (Top Paste Mask, stencil)
• Apogee_v100_Signal_Top.GBR (Top Copper Layer)
• Apogee_v100_Internal_Plane_1.GBR (Internal Copper Layer GND)
• Apogee_v100_Internal_Plane_2.GBR (Internal Copper Layer +3.3V)
• Apogee_v100_Signal_Bottom.GBR (Bottom Copper Layer)
• Apogee_v100_Paste_Mask_Bottom.GBR (Bottom Paste, stencil)
• Apogee_v100_Soldermask_Bottom.GBR (Bottom Solder Mask)
• Apogee_v100_Outline.GBR (Board Outline)
• Apogee_v100_Drill.GBR (NC XY coordinates & Drill tools sizes)

Assembly

Components Layout

• 

  Apogee v1.00 bottom components Layout

• 

  Apogee v1.00 top components Layout

• 

  Apogee v1.00 bottom components detail

• 

  Apogee v1.00 top components detail

Bill Of Material

Download Apogee v1.00 Bill of Material (zipped .xls file)

PCB and assembled boards suppliers

Check availability on Get Hardware page

Mechanical Dimensions

Programming

Apogee autopilot can reprogrammed in two different ways:

• using the MCU native (embedded in rom) DFU USB bootloader over the on-board USB header (so pre-loading an "external" bootloader is useless)
  • required hardware : usb cable with usb-mini connector
  • required software : dfu_util tool (present in ubuntu repository)
• using the SWD (Serial Wire Debug) connector
  • required hardware : usb cable with usb-mini connector, molex to 2.54mm pitch pin cable, swd part of a cheap stm32 evaluation board (any discovery board, start @ 8$)
  • required software : st_flash and st_util, have to be compiled from source (https://github.com/texane/stlink)

On-board Data Logging

It is possible to write data on the embedded SD card from the main autopilot program. In order to cope with a real-time constraints of the autopilot, a light RTOS called ChibiOS is used to split the logging task from the rest of the system. Two modules are necessary to enable the logging system: the driver of the SD card system that also handle the file system (using FATFS) and a dynamic memory allocation system called TLSF. In order to enable this features for your apogee board, you need to select the correct board type and add the required modules to the firmware section of your airframe file (logging is currently only available for fixedwing firmware):

<firmware name="firmware">
 ...
 <target name="ap" board="apogee_1.0_chibios">
   ...
 </target>
 ...
 <module name="tlsf"/>
 <module name="logger" type="sd_chibios"/>
</firmware>

This will active the automatic opening of a new log file (30 seconds) after each startup of the autopilot. Then you can freely write ASCII or binary data into this file (see a simple example logging for meteorological data logging). The file is automatically closed upon battery disconnection, no need to press any button to stop the logging.

To recover the data on the SD card, just power up the board without the USB plugged (otherwise it will enter in DFU boot mode), then plus the USB cable to the board and to your computer. This will stop the main autopilot program and will mount the SD card as a regular mass storage with a FAT file system. The log files are placed in a PPRZ folder. Unplugging the USB will reset the autopilot.

In addition to this, you can also load a flight recorder module (it also needs the pprzlog module for supporting the specific paparazzi binary log format).

<firmware>
 ...
 <module name="pprzlog"/>
 <module name="flight_recorder"/>
 ...
</firmware>

with the appropriate telemetry file (conf/telemetry/fixedwing_flight_recorder.xml). This will automatically open a second file where telemetry messages described in the FlightRecorder section of the telemetry file will be logged in binary format. The files are store in a separated FR folder on the SD card. The decoding procedure is the same than OpenLog and is using the sd2log tool:

~/paparazzi/sw/logalizer/sd2log [log_file] [optinal_output_dir]

This will produce 3 files: a .log and a .data files similar to the normal ground station log and .tlm file that is a simple copy of the binary file (but rename with the same base name than the two others).

Debugging

Debugging with STM Discovery ST-LINK/V2 embedded debug tool

Debugging with CricketProbe

Debugging with Black Magic Probe

Source Files

Apogee v1.00 hardware design (zipped Protel99SE SP6 database file)

Source code

Available in latest git master branch

Where to Buy

You can purchase Apogee V1.00 from one of the following stores:

• Drotek
• EasyDrone
• GoodluckBuy (xD)
• Alibaba