Umarim Lite v2
Revision as of 00:52, 6 July 2012 by Michel (talk | contribs) (→PCB and assembled boards suppliers)
Hardware Revision History
| Version # | Release Date | Release Notes |
|---|---|---|
| v2 | 07/2012 | Minor PCB modifications |
| v1 | 03/2012 | Initial release of Umarim Lite |
Features
- NXP LPC2148 MCU based
- 1 x Triple axis Digital Gyroscope (Invensense ITG-3200)
- 1 x Triple axis Digital Accelerometer (Analog Devices ADXL345)
- 6 x Servo PWM outputs
- 1 x R/C receiver PPM frame input
- 2 x UART (TTL 3.3V, 5V tolerant)
- 2 x I2C bus
- 1 x SPI bus
- 1 x USB (client)
- 4 x General Purpose I/O or Analog input channels (0V - 3.3V)
- 5v / 1.5A switching power supply (input voltage range 5.5V min → 17.0v max)
- 3.3v / 1A linear regulator
- 2 x status LEDs
- 8 grams (0,3 oz)
- 53 x 25mm (2.1" x 0.98")
- 4 layers PCB design / single side SMD components
Umarim Lite v2 3D bottom view
Umarim Lite v2 3D top view
- UmarimLite v2 top side.png
Umarim Lite v2 top side
- UmarimLite v2 bottom side.png
Umarim Lite v2 bottom side
Pinout
Pins Name and Type are specified with respect to the Autopilot Board
| Pin # | Name | Type | Description | Color |
|---|---|---|---|---|
| 1 | GND | PWR | common ground | Black |
| 2 | +5V | PWR | 5V Rail from autopilot | Orange |
| 3 | SRVx | OUT | Servo signal (PWM) | White |
| Pin # | Name | Type | Description | Color |
|---|---|---|---|---|
| 1 | GND | PWR | common ground | Black |
| 2 | +5v | PWR | 5V Rail from autopilot | Orange |
| 3 | PPM_IN | IN | PPM Stream from R/C Receiver (5V tolerant) | White |
| Pin # | Name | Type | Description | Color |
|---|---|---|---|---|
| 1 | GND | PWR | common ground | Black |
| 2 | +3.3V | PWR | 3.3V Rail from autopilot | Red |
| 3 | SSEL1 | IN | SSP Slave Select. Selects the SSP interface as a slave (SSEL1) | Brown |
| 4 | MOSI1 | I/O | SPI1 Master Out Slave In. Data output from master / data input to slave | Grey |
| 5 | MISO1 | I/O | SPI1 Master In Slave Out. Data input to master / data output from slave | Green |
| 6 | DRDY1 | IN | External interrupt 0 input (EINT0) | Purple |
| 7 | SCK1 | I/O | SPI1 Serial clock. Clock output from master or input to slave | Yellow |
| Pin # | Name | Type | Description | Color |
|---|---|---|---|---|
| 1 | GND | PWR | common ground | Black |
| 2 | +5V | PWR | 5V Rail from autopilot | Orange |
| 3 | +3.3V | PWR | 3.3V Rail from autopilot | Red |
| 4 | AUX1 | I/O | General Purpose I/O #1 or ADC Input ADC_0 (lpc AD1.5) | |
| 5 | AUX2 | I/O | General Purpose I/O #2 or ADC Input ADC_1 (lpc AD1.4) | |
| 6 | AUX3 | I/O | General Purpose I/O #3 or ADC Input ADC_2 (lpc AD1.3) | |
| 7 | AUX4 | I/O | General Purpose I/O #4 or ADC Input ADC_3 (lpc AD1.2) |
| Pin # | Name | Type | Description | Color |
|---|---|---|---|---|
| 1 | GND | PWR | common ground | Black |
| 2 | +5V | PWR | 5V Rail from autopilot | Orange |
| 3 | +3.3V | PWR | 3.3V Rail from autopilot | Red |
| 4 | RXD0 | IN | UART0 Serial Input (3.3V level, 5V Tolerant) | Green |
| 5 | TXD0 | OUT | UART0 Serial Output (3.3V level) | Blue |
| Pin # | Name | Type | Description | Color |
|---|---|---|---|---|
| 1 | GND | PWR | common ground | Black |
| 2 | +5V | PWR | 5V Rail from autopilot | Orange |
| 3 | +3.3V | PWR | 3.3V Rail from autopilot | Red |
| 4 | RXD1 | IN | UART1 Serial Input (3.3V level, 5V Tolerant) | Green |
| 5 | TXD1 | OUT | UART1 Serial Output (3.3V level) | Blue |
| Pin # | Name | Type | Description | Color |
|---|---|---|---|---|
| 1 | GND | PWR | common ground | Black |
| 2 | +5V | PWR | 5V Rail from autopilot | Orange |
| 3 | +3.3V | PWR | 3.3V Rail from autopilot | Red |
| 4 | SDA0 | Open Drain I/O |
I2C0 bus Serial DAta | Brown |
| 5 | SCL0 | Open Drain I/O |
I2C0 bus Serial CLock | Blue |
| Pin # | Name | Type | Description | Color |
|---|---|---|---|---|
| 1 | GND | PWR | common ground | Black |
| 2 | +5V | PWR | 5V Rail from autopilot | Orange |
| 3 | +3.3V | PWR | 3.3V Rail from autopilot | Red |
| 4 | SDA1 BOOT |
Open Drain I/O |
I2C1 bus Serial DAta In-Circuit Serial Programming (ISP) enable (P0.14, +3.3v pullup) (Note) |
Brown |
| 5 | SCL1 | Open Drain I/O |
I2C1 bus Serial CLock | Blue |
Note: Holding this pin low for at least 3mS after a RESET (or power up) instructs the controller to enter programming mode.
| Pin # | Name | Type | Description | Color |
|---|---|---|---|---|
| 1 | GND | PWR | common ground | Black |
| 2 | USB+ | I/O | USB bidirectional D+ line | Green |
| 3 | USB- | I/O | USB bidirectional D- line | White |
| 4 | VBUS | IN | Indicates the presence of USB bus power (P0.23) (5V level) | Orange |
Note: MiniUSB and Molex USB connectors are in parallel, only one can be connected at a time.
Schematic
Assembly
Components Layout
Umarim Lite v2 bottom components Layout
Umarim Lite v2 top components Layout
Umarim Lite v2 bottom components detail
Umarim Lite v2 top components detail
PCB and assembled boards suppliers
Check availability on Get Hardware page
Mechanical Dimensions
Umarim v1.0 Mechanical Dimensions
Paparazzi USB Bootloader Upload
Required components
- 1 x FTDI TTL-232R-3V3 (Digikey #768-1015-ND) USB to UART converter cable with +3.3V TTL level UART signals. (see Note 1)
- 2 x 4-pin connector housing Molex Picoblade 51021-0400 (Digikey #WM1722-ND)
- 5 x crimp terminal female Molex Picoblade 50058-8000 (Digikey #WM1775CT-ND)
- 1 x 6-pin 0.1" pitch single in line male connector header Samtec TSW-132-07-TS (Digikey #SAM1035-32-ND) or equivalent
- 28-32AWG wiring cable
- Note1: It is advised to use FTDI USB-serial converter, as serial FTDI chips are by default working well in Linux.
- The Paparazzi ground station software is configured to look for modems on FTDI ports by default.
- This harness can also serve as a modem interface (after it's use in Bootloader uploading) if you plug it on Umarim's UART1 connector
Connection Diagram
Make up a wiring harness similar to the following
Boot Sequence
