Chimera/v1.00

Autopilots Booz HB Autopilots Lisa Tiny YAPA Autopilots Ap.parrot minidrone Apogee/v1.00 HITL Autopilots Bebop Booz Chimera/v1.00 Classix CrazybeeF4Pro Disco Elle Elle0 Future Autopilots Krooz KroozSD LinAM V4 Lisa Lisa/Bone Lisa/L Lisa/M Lisa/M v1.0 Lisa/M v2.0 Lisa/MX Lisa/S NavGo v3 NavStik Pixhawk Pixracer Previous Autopilots STM32F4 Discovery STM32F429I Discovery Tawaki/v1.00 Tawaki/v1.10 Tawaki/v2.01 TWOG/v1.0 Umarim Lite v2 Umarim v1.0 Xvert

Overview

• STMicro STM32F767 Micro Controller Unit (ARM Cortex-M7, 216 MHz CPU, FPU & DSP instructions, 2 Mbytes Flash, 512 Kbytes SRAM, General-purpose DMA,etc.)
• 9 DOF Inertial Measurement Unit
• Barometer/altimeter (I2C, IMU slave capability)
• Differential Pressure Sensor for Pitot tube
• microSD card (+ dedicated power supply for emergency files closing system)
• All connectors available both in standard 0.1” header and Molex Picoblade (except servos and R/C receiver, 0.1” header only)
• Dedicated serial link and power supply for "Companion Board" (Beaglebone, Raspberry, Gumstix, ...)
• x4 status Leds + 8 segments LED display
• SWD debug connector (STM STLink compliant header)
• x8 Servos (+ Servos Power supply selection capabilities: Chimera onboard power supply or external source)
• x2 RC Receiver inputs (S.BUS, PPM & Spektrum Satellite compatible, including receiver binding)
• x5 UARTs (including one with hardware flow control signals)
• x1 I2C bus (3.3V and 5V logic level)
• x1 SPI bus (with Slave Select, Master or Slave)
• x1 CAN bus
• x8 auxiliary Inputs/Outputs spread over 2 connectors (x6 ADC, x6 Timers different from servos, x1 UART, x1 DAC)
• XBEE modem holder (ASSO and Reset connected to MCU GPIOs)
• x1 USB :
  • DFU mode (download) or USB storage (direct access to MicroSD card)
  • micro-USB plug (+ Picoblade & 0.1” header in //)
  • Board can be flashed even if aircraft battery is off)
• Controlled Powerswitch 5V supply on AUX A (AUX0 to 3) header
• Twin switching power supply :
  • source 2 to 6 Lipo cells (6 to 26v)
  • 5v/3A for “Companion” board (controlled by GPIO)
  • 5v/3A dedicated to Chimera (servos and other 5v peripherals)
• VBat+Gnd connectors for peripheral
• 89x60mm (3.5x2.4")

Hardware Revision History

Version #	Release Date	Release Notes
v1.00	10/2016	Initial release of Chimera

Detailed Features

SDIO (MicroSD card)

• software support available with v5.2 and above
• hi-cap power designed to give enough time to cleanly save buffer and close file(s) when power outage detected
• USB-storage mode when plugging an USB cable after startup

Sensors

• 9 DOF IMU
  Invensense chip MPU-9250 : 9 DOF, 3 axis Accelerometer + 3 axis Gyroscope + 3 axis Magnetometer
• Barometer/Altimeter
  TE Connectivity module MS5611-01BA03 : High resolution Integrated digital pressure sensor, 10 to 1200 mbar, 24 bit ADC, I2C & SPI interface
• Differential pressure sensor / Pitot
  TE Connectivity transducer MS4525DO-DS5AI001DP : Digital Output Temperature and Differential Pressure sensor, Dual Sideport, 1PSI pressure range, I2C interface

USB Modes

• USB plugged before autopilot is powered : enter DFU mode to be flashed (can be flashed even if autopilot is not powered)
• USB plugged after autopilot is powered : stop ap task, enter usb storage mode to made sdcard content easily avalaible, after the host has mounted;copied;dismounted storage;unplugged usb, ap restart

SWD: Serial Wire Debug

Permits flash and source level debugging via SWD part of cheap discovery card, or via more capable, fastest, more expensive probe like black magic probe or CricketProbe

R/C Serial

Chimera offer two different R/C Receiver port allowing direct connection (3 pin) of several brand off-the-shelf receivers without hardware modification or external encoder board:

• RC1: PPM (Timer2 or 5 / Ch2) or S.BUS (inverted UART4 Rx) or Serial (non-inverted UART4 Rx) or Serial Spektrum satellite (non-inverted UART4 Rx + GPIO for binding procedure)
• RC2: S.BUS (inverted UART7 Rx) or Serial (non-inverted UART7 Rx) or Serial Spektrum satellite (non-inverted UART4 Rx + GPIO for binding procedure)

Power

The input power source (Battery) voltage range of Chimera is 6V to 26V (2 to 6 Lipo cells)

• Twin Power Supply
  • one 5V/3A dedicated to Chimera, servos (see Servo Power Supply selection below) and other 5V peripheral
  • one 5V/3A dedicated to "Companion Board" available on UART1 connector ("5V Comp.",#2) can be switched ON and OFF on demand using EN_COMP (MCU GPIO output PC04).
    • EN_COMP = 1 => 5V Comp. OFF
    • EN_COMP = 0 => 5V Comp. ON (default)

• Servo Power Supply selection
  Chimera offer 2 options for servo power supply
  • Onboard 5V, provided total current (autopilot + external 5V modules + servos) does not exceed 3A.
  • External 5V source (BEC) for special servo configuration

(see Servo Power options section below for more information)

• Power Switch
  5V power output pin on AUX A connector ("5V Aux.",#2) can be switched ON and OFF on demand using APSW (MCU GPIO output PE06).
  • APSW = 0 => 5V Aux OFF
  • APSW = 1 => 5V Aux ON (default)

The internal switch TPS2051B is designed to withstand 500mA continuous current and is short-circuit and thermally protected.
(see TPS2051B datasheet for recommended operation conditions)

Onboard Modem

Chimera offer two options for Modem:

• External Modem.
  In this case, Modem should be plugged on "UART3" connector.
• Onboard XBee module.
  In this case, XBee pins are connected to :
  • Dout -> UART3 Rx (PD09)
  • Din -> UART3 Tx (PD08)
  • Asso -> GPIO (PA08)
  • Reset -> GPIO (PE15)
    

Buses

• I2C

• SPI

• CAN

Pinout

Pins Name and Type are specified with respect to the Autopilot Board

General Pinout

UART1 (Companion)

Pin #	Name	Type	MCU Port	Description
1	GND	PWR	-	common ground
2	+5V Comp.	PWR	Controlled by PC5	5V/3A specific for Companion board (PC5 = LOW => ON (default, pulldown) / PC5 = High => OFF)
3	+3.3V	PWR	-	3.3V Rail from autopilot
4	RX1	IN	PB7	UART1 Serial Input (3.3V level, 5V tolerant)
5	TX1	OUT	PB6	UART1 Serial Output (3.3V level)

UART2

Pin #	Name	Type	MCU Port	Description
1	GND	PWR	-	common ground
2	+5V	PWR	-	5V Rail from autopilot
3	+3.3V	PWR	-	3.3V Rail from autopilot
4	RX2	IN	PD6	UART2 Serial Input (3.3V level, 5V tolerant)
5	TX2	OUT	PD5	UART2 Serial Output (3.3V level)
6	RTS2	OUT	PD4	UART2 Flow Control Request to Send (3.3V level)
7	CTS2	IN	PD3	UART2 Flow Control Clear to Send (3.3V level, 5V tolerant)

UART3 (Modem)

Pin #	Name	Type	MCU Port	Description
1	GND	PWR	-	common ground
2	+5V	PWR	-	5V Rail from autopilot
3	+3.3V	PWR	-	3.3V Rail from autopilot
4	RX3	IN	PD9	UART3 Serial Input (3.3V level, 5V tolerant) DO NOT USE if XBee module present on Chimera
5	TX3	OUT	PD8	UART3 Serial Output (3.3V level) DO NOT USE if XBee module present on Chimera

UART8 (GPS Receiver)

Pin #	Name	Type	MCU Port	Description
1	GND	PWR	-	common ground
2	+5V	PWR	-	5V Rail from autopilot
3	+3.3V	PWR	-	3.3V Rail from autopilot
4	RX8	IN	PE0	UART8 Serial Input (3.3V level, 5V tolerant)
5	TX8	OUT	PE1	UART8 Serial Output (3.3V level)

I2C2 (3V3)

Pin #	Name	Type	MCU Port	Description
1	GND	PWR	-	common ground
2	+5V	PWR	-	5V Rail from autopilot
3	+3.3V	PWR	-	3.3V Rail from autopilot
4	SDA2	Open Drain I/O	PB11	I2C2 bus Serial DAta (3.3V level, 1.5k pull-up)
5	SCL2	Open Drain I/O	PB10	I2C12 bus Serial CLock (3.3V level, 1.5k pull-up)

Note: 2 x Molex Picoblade and 2 x 0.1" Header are all in parallel

I2C2 (5V)

Pin #	Name	Type	MCU Port	Description
1	GND	PWR	-	common ground
2	+5V	PWR	-	5V Rail from autopilot
3	+3.3V	PWR	-	3.3V Rail from autopilot
4	SDA2	Open Drain I/O	PB11	I2C2 bus Serial DAta (5V level, 3.3k pull-up)
5	SCL2	Open Drain I/O	PB10	I2C12 bus Serial CLock (5V level, 3.3k pull-up)

SPI1

Pin #	Name	Type	MCU Port	Description
1	GND	PWR	-	common ground
2	+5V	PWR	-	5V Rail from autopilot
3	+3.3V	PWR	-	3.3V Rail from autopilot
4	NSS1	OUT	PA15	Slave Select. Selects the SPI slave
5	MOSI1	I/O	PB5	SPI1 Master Out Slave In. Data output from master / data input to slave
6	MISO1	I/O	PB4	SPI1 Master In Slave Out. Data input to master / data output from slave
7	SCK1	I/O	PB3	SPI1 Serial clock. Clock output from master or input to slave

AUX A

Pin #	Name	Type	MCU Port	Description
1	GND	PWR	-	common ground
2	+5V Aux	PWR	Controlled by PC4	5V from autopilot through Power Switch (PC4 = LOW => OFF / PC4 = High => ON)
3	+3.3V	PWR	-	3.3V Rail from autopilot
4	AUX0	I/O	PA5	General Purpose I/O / ADC1+2 in5 / DAC2 / TIM2 ch1
5	AUX1	I/O	PA3	General Purpose I/O / ADC1+2+3 in3 / TIM2 ch4 / TIM5 ch4 / TIM9 ch2
6	AUX2	I/O	PA2	General Purpose I/O / ADC1+2+3 in2 / TIM2 ch3 / TIM5 ch3 / TIM9 ch1
7	AUX3	I/O	PA0	General Purpose I/O / ADC1+2+3 in0 / TIM2 ch1 / TIM5 ch1

AUX B

Pin #	Name	Type	MCU Port	Description
1	GND	PWR	-	common ground
2	+5V	PWR	-	5V Rail from autopilot
3	+3.3V	PWR	-	3.3V Rail from autopilot
4	AUX4	I/O	PC3	General Purpose I/O / ADC1+2+3 in13
5	AUX5	I/O	PC2	General Purpose I/O / ADC1+2+3 in12
6	AUX6	I/O	PC6	General Purpose I/O / TIM3 ch1 / TIM8 ch1 / UART6 Tx
7	AUX7	I/O	PC7	General Purpose I/O / TIM3 ch2 / TIM8 ch2 / UART6 Rx

CAN

Pin #	Name	Type	MCU Port	Description
1	GND	PWR	-	common ground
2	+5V	PWR	-	5V Rail from autopilot
3	CANH	I/O	-	CAN bidirectional + line
4	CANL	I/O	-	CAN bidirectional - line

Note: Embedded 120R terminator resistor.

USB

Pin #	Name	Type	MCU Port	Description
1	GND	PWR	-	common ground
2	USB+	I/O	PA12	USB bidirectional D+ line
3	USB-	I/O	PA11	USB bidirectional D- line
4	VBUS	IN	PA9	Indicates the presence of USB bus power (5V level), DFU or USB storage Mode selection (BOOT0 MCU pin)

Note: MicroUSB, Molex Picoblade and 0.1" Header USB connectors are in parallel, only one can be connected at a time.

SWD (Serial Wire debug)

Pin #	Name	Type	MCU Port	Description
1	+3.3V	PWR	-	3.3V Rail from autopilot
2	SWCLK	IN	PA14	SWD Serial Clock
3	GND	PWR	-	common ground
4	SWDIO	I/O	PA13	SWD Serial Data
5	RST	IN	NRST	MCU Reset
6	NC	-	-	Not connected, for STM ST-LINK/V2 connector compliance

Note: Pin to pin compatible with STM ST-LINK/V2 debug tool connector

Power Out

Pin #	Name	Type	Description
1	GND	PWR	common ground use only to power peripheral modules, DO NOT use as power supply input for autopilot
2	VBAT	PWR	+ Rail from battery use only to power peripheral modules, DO NOT use as power supply input for autopilot

R/C Receivers and Servos header pinout

RC Receiver 1

Pin #	Name	Type	MCU Port	Description
1	GND	PWR	-	common ground
2	+5V	PWR	-	5V Rail from autopilot
3	RC1	I/O	PA1	Serial (SBUS, Spektrum, etc.) or PPM Stream RC receiver signal (5V Tolerant) UART4 Rx / TIM2 ch2 / TIM5 ch2

RC Receiver 2

Pin #	Name	Type	MCU Port	Description
1	GND	PWR	-	common ground
2	+5V	PWR	-	5V Rail from autopilot
3	RC1	IN	PE7	Serial (SBUS, Spektrum, etc.) RC receiver signal (5V Tolerant) UART7 Rx

Servo 0/1/2/3/4/5/6/7

Pin #	Name	Type	MCU Port	Description
1	GND	PWR	-	common ground
2	+5V Servo	PWR	-	5V Rail for Servos
3	SRV0 SRV1 SRV2 SRV3 SRV4 SRV5 SRV6 SRV7	OUT	PA6 PA7 PB0 PB1 PD12 PD13 PD14 PD15	Servo signal (PWM)

Servo Power options

There is two options to supply connected servos.
Note : Whatever option is chosen, autopilot's ground already connected to servomotor's ground.

Powering Servos with Autopilot

This option can be used provided total current from 5V rail (autopilot + external 5V modules + servos) does not exceed 3A.
In this case, 5V servo rail must be connected to autopilot 5V rail as described below.

Warning: make sure shunt current rating exceed servos total consumption
A practical way of making this connection is to use a 2 or 3 way shunt like Samtec's MNT-103-BK-G (3.9A/pin)

Powering Servos using an external BEC/Power Source

This option must be used if total current from 5V rail may exceed 3A or for other special servo configuration.

Assembly

Bill Of Material

Download Chimera v1.00 Bill of Material (zipped LibreOffice Calc & PDF file)

PCB and assembled boards suppliers

Check availability on Get Hardware page

Mechanical Dimensions