Difference between revisions of "Tawaki/v1.00"

From PaparazziUAV
Jump to navigation Jump to search
Line 306: Line 306:


=== Power Supply ===
=== Power Supply ===
==== External source on GND & VBAT pads ====
==== External source on "Servos b" header ====
==== USB Micro-B Powering ====
==== External 5V source ====


=== USB Modes ===
=== USB Modes ===

Revision as of 07:03, 5 July 2019

Tawaki v1.00 top side

Tawaki v1.00 1€ size comparison

Hardware Revision History

Version # Release Date Release Notes
v1.00 07/2019 Initial release of Tawaki

Overview

Pictures

Key Features

  • STMicro STM32F777VI Micro Controller Unit
    • ARM Cortex-M7, 216 MHz CPU, FPU & DSP instructions, 2 Mbytes Flash, 512 Kbytes SRAM, General-purpose DMA, HW Crypto,etc.
  • On-board Sensors
    • 6 DOF Accelerometers & Gyrometers TDK-Invensense ICM-20600
    • 3 DOF Magnetometer STMicro LIS3MDL
    • Baro-Altimeter Bosch BMP388
  • 8x Servos or ESC outputs (PWM/OneShot/DShot) + D-Shot Telemetry serial input
  • 2x RC Receiver Inputs (S.BUS, PPM & Spektrum Satellite compatible, including receiver binding)
  • Communication Buses
    • 3x UARTs (including one with hardware flow control signals)
    • 1x I2C bus (3.3V and 5V logic level)
    • 1x SPI bus (with Slave Select, Master or Slave)
    • 1x CAN bus
    • 1x USB (Micro-B & remote) : DFU mode (download) or USB storage (direct access to MicroSD card) or FullSpeed Mode
  • 8x Auxiliary Inputs/Outputs spread over 2 connectors (8x ADC, 8x Timers different from servos, x1 UART, etc.)
  • MicroSD card (+ dedicated power supply for emergency files closing system)
  • Debug Connector (Serial Wire Debug)
  • Power
    • source 2 to 4 Lipo cells (6 to 17v)
    • 5V/4A (max total for Tawaki + Servos + Payload)
    • 3.3V/3A Low Noise (max total for payload)
    • Controlled PowerSwitch 5V/2A supply on AUX A connector
  • x4 Status Leds
  • Connectors fully compatible with Apogee autopilot
  • Mechanical
    • 53 x 25mm (2.1" x 0.98"), including 4x Φ2mm mounting holes (shares the same external dimensions and mounting points as Apogee)
    • 4x Φ3mm extra mounting holes, 30 to 31mm spacing (30.5mm standard from Racers ESC, GPS modules, etc. )
    • 11g (0.4 oz) (including Micro-SD card)

Pinout

Simplified Pinout Diagram (Paparazzi use)

Pins Name and Type are specified with respect to the Autopilot Board

Tawaki v1.00 simplified pinout (Paparazzi use)

Simplified Pinout Tables (Paparazzi use)

Servos a1 / a2 / a3 / a4

Pin # Name Type MCU Port MCU Resource Description
1 GND PWR - - common ground
2 +5V PWR - - 5V Rail from autopilot
3 SRVa1
SRVa2
SRVa3
SRVa4
OUT PE9
PE11
PE13
PE14
Tim1.Ch1
Tim1.Ch2
Tim1.Ch3
Tim1.Ch4
Servo signal (PWM)


Servos b

Pin # Name Type MCU Port MCU Resource Description
1 GND PWR - - common ground
2 VBAT PWRIN/OUT - - Battery Rail (if solder bridge JP1 ON)
3 SRVb1 OUT PB6 Tim4.Ch1 Servo signal (PWM)
4 SRVb2 OUT PB7 Tim4.Ch2 Servo signal (PWM)
5 SRVb3 OUT PB8 Tim4.Ch3 Servo signal (PWM)
6 SRVb4 OUT PB9 Tim4.Ch4 Servo signal (PWM)
7 DSHTin IN PB5 UART5.Rx DShot Telemetry serial input


R/C

Pin # Name Type MCU Port MCU Resource Description
1 GND PWR - - common ground
2 +5V PWR - - 5V Rail from autopilot
3 +3.3V PWR - - 3.3V Rail from autopilot
4 RC1 IN PE0 UART8.Rx (5V Tolerant) Serial (SBUS, Spektrum, etc.)
5 RC2 IN PC6 UART6.Rx (Tx software swap)
Tim3.Ch1
Tim8.Ch1
(5V Tolerant) Serial (SBUS, Spektrum, etc.) or PPM Stream RC receiver signal


UART2

Pin # Name Type MCU Port Description
1 GND PWR - common ground
2 +5V PWR - 5V Rail from autopilot
3 +3.3V PWR - 3.3V Rail from autopilot
4 RX2 IN PD6 UART2 Serial Input (3.3V level)
5 TX2 OUT PD5 UART2 Serial Output (3.3V level)


UART3

Pin # Name Type MCU Port Description
1 GND PWR - common ground
2 +5V PWR - 5V Rail from autopilot
3 +3.3V PWR - 3.3V Rail from autopilot
4 RX2 IN PD9 UART3 Serial Input (3.3V level)
5 TX2 OUT PD8 UART3 Serial Output (3.3V level)


UART7

Pin # Name Type MCU Port Description
1 GND PWR - common ground
2 +5V PWR - 5V Rail from autopilot
3 +3.3V PWR - 3.3V Rail from autopilot
4 RX2 IN PB3 UART7 Serial Input (3.3V level)
5 TX2 OUT PA15 UART7 Serial Output (3.3V level)


I2C2 (3V3)

Pin # Name Type MCU Port Description
1 GND PWR - common ground
2 +5V PWR - 5V Rail from autopilot
3 +3.3V PWR - 3.3V Rail from autopilot
4 SDA2 3.3V Open Drain I/O PB11 I2C2 bus Serial DAta (3.3V level, 2.2kΩ pull-up)
5 SCL2 3.3V Open Drain I/O PB10 I2C12 bus Serial CLock (3.3V level, 2.2kΩ pull-up)


I2C2 (5V)

Pin # Name Type MCU Port Description
1 GND PWR - common ground
2 +5V PWR - 5V Rail from autopilot
3 +3.3V PWR - 3.3V Rail from autopilot
4 SDA2 5V Open Drain I/O PB11 I2C2 bus Serial DAta (5V level, 2.2kΩ pull-up)
5 SCL2 5V Open Drain I/O PB10 I2C12 bus Serial CLock (5V level, 2.2kΩ pull-up)


SPI2

Pin # Name Type MCU Port Description
1 GND PWR - common ground
2 +5V PWR - 5V Rail from autopilot
3 +3.3V PWR - 3.3V Rail from autopilot
4 NSS2 OUT PB12 Slave Select. Selects the SPI slave
5 MOSI2 I/O PB15 SPI2 Master Out Slave In. Data output from master / data input to slave
6 MISO2 I/O PB14 SPI2 Master In Slave Out. Data input to master / data output from slave
7 SCK2 I/O PD3 SPI2 Serial clock. Clock output from master or input to slave


CAN

Pin # Name Type MCU Port Description
1 CANL I/O - CAN bidirectional - line
2 CANH I/O - CAN bidirectional + line

Note: Embedded 120Ω terminator resistor.

AUX a

Pin # Name Type MCU Port MCU Resource Description
1 GND PWR - - common ground
2 +5V Aux PWR (Controlled by) PC13 - 5V from autopilot through Power Switch
(PC13 = Low => OFF / PC13 = High => ON)
3 +3.3V PWR - - 3.3V Rail from autopilot
4 AUXa1 I/O PA0 ADC1+2+3.In0
Tim2.Ch1
Tim5.Ch1
UART4.Tx
UART2.CTS
General Purpose I/O
5 AUXa2 I/O PA1 ADC1+2+3.In1
Tim2.Ch2
Tim5.Ch2
UART4.Rx
UART2.RTS
General Purpose I/O
6 AUXa3 I/O PA2 ADC1+2+3.In2
Tim2.Ch3
Tim5.Ch3
Tim9.Ch1
General Purpose I/O
7 AUXa4 I/O PA6 ADC1+2.In6
Tim3.Ch1
Tim13.Ch1
General Purpose I/O


AUX b

Pin # Name Type MCU Port MCU Resource Description
1 GND PWR - - common ground
2 +5V PWR - - 5V Rail from autopilot
3 +3.3V PWR - - 3.3V Rail from autopilot
4 AUXb1 I/O PA3 ADC1+2+3.In3
Tim2.Ch4
Tim5.Ch4
Tim9.Ch2
General Purpose I/O
5 AUXb2 I/O PA7 ADC1+2+3.In7
Tim3.Ch2
Tim14.Ch1
General Purpose I/O
6 AUXb3 I/O PB0 ADC1+2.In8
Tim3.Ch3
General Purpose I/O
7 AUXb4 I/O PB1 ADC1+2.In9
Tim3.Ch4
General Purpose I/O


USB

Pin # Name Type MCU Port Description
1 GND PWR - common ground
2 USB+ I/O PA12 USB bidirectional D+ line
3 USB- I/O PA11 USB bidirectional D- line
4 VBUS IN PA9 USB bus power (5V)
5 BOOT IN BOOT0 DFU or USB Mode selection (BOOT0 MCU pin)

Note: USB Micro-B and Molex Picoblade connectors are in parallel, only one should be connected at a time.


SWD

Pin # Name Type MCU Port Description
1 GND PWR - common ground
2 +3.3V PWR - 3.3V Rail from autopilot
3 nRST IN NRST MCU Reset (active low)
4 SWCLK IN PA14 Serial Wire Clock
5 SWDIO I/O PA13 Serial Wire Data Input/Output


Detailed Features

Power Supply

External source on GND & VBAT pads

External source on "Servos b" header

USB Micro-B Powering

External 5V source

USB Modes

General Pinout

Pins Name and Type are specified with respect to the Autopilot Board

Tawaki v1.00 general pinout (development board use)

Schematic

Mechanical Dimensions

Board production

Gerber & Drill for PCB

Bill Of Material

Components Layout

Pick-and-Place

Programming

Debugging

Debugging with STM Discovery ST-LINK/V2 embedded debug tool

Debugging with BlackMagic probe

Debugging with CricketProbe

Source code

Available in latest git master branch.

Where to Buy

Check availability on Get Hardware page