Difference between revisions of "Module/Servo switch"

From PaparazziUAV
Jump to navigation Jump to search
m
(fix some errors)
 
(3 intermediate revisions by one other user not shown)
Line 3: Line 3:


To use it load the servo_switch module:
To use it load the servo_switch module:
<pre>
{{Box Code|conf/airframes/myplane.xml|
<source lang="xml">
   <modules>
   <modules>
     ...
     ...
     <load name="servo_switch.xml"/>
     <load name="servo_switch.xml"/>
   </modules>
   </modules>
</pre>
</source>
}}


Now you only have to declare a servo in your airframe.xml that you
Now you only have to declare a servo in your airframe.xml that you
want to use. Previously you had to set up commands, command laws as
want to use.
well.
 
== Configuration ==


By default the servo_switch module looks for a servo called SWITCH.
By default the servo_switch module looks for a servo called SWITCH.
The switch on value is 2000us and switch off is 1000us by default.
The switch on value is 2000us and switch off is 1000us by default.
e.g. in my airframe file I have:
e.g. in my airframe file I have:
<servos>
{{Box Code|conf/airframes/myplane.xml|
  ....
<source lang="xml">
  <servo name="SWITCH" no="7" min="1000" neutral="1500" max="2000"/>
  <servos>
</servos>
    ....
 
    <servo name="SWITCH" no="7" min="1000" neutral="1500" max="2000"/>
  </servos>
</source>
}}


If you want to use a different servo/values you can set that in the
If you want to use a different servo/values you can set that in the
modules section, e.g. for a servo named HATCH:
modules section, e.g. for a servo named HATCH:
<load name="servo_switch.xml">
{{Box Code|conf/airframes/myplane.xml|
    <define name="SERVO_SWITCH_ON_VALUE"  value="1100"/>
<source lang="xml">
    <define name="SERVO_SWITCH_OFF_VALUE" value="1900"/>
  <modules>
    <define name="SERVO_SWITCH_SERVO"    value="SERVO_HATCH"/>
    <load name="servo_switch.xml">
</load>
      <define name="SERVO_SWITCH_ON_VALUE"  value="1100"/>
      <define name="SERVO_SWITCH_OFF_VALUE" value="1900"/>
      <define name="SERVO_SWITCH_SERVO"    value="HATCH"/>
  </load>
  </modules>
</source>
}}
Of course you only have to set these parameters here If you do not
Of course you only have to set these parameters here If you do not
want to use the DEFAULT servo (SWITCH) or the default on/off values.
want to use the DEFAULT servo (SWITCH) or the default on/off values. Switch value will not go outside the range defined on the servo


=== Calling from Flight Plan ===
=== Calling from Flight Plan ===
In your flight plan you just call the makro defined in servo_switch.h
In your flight plan you just call the macro defined in servo_switch.h
  <call fun="ServoSwitchOn()"/>
<source lang="xml"><call fun="ServoSwitchOn()"/></source>
or
or
  <call fun="ServoSwitchOff()"/>
<source lang="xml"><call fun="ServoSwitchOff()"/></source>
respectively.
respectively.


=== Buttons in the GCS ===
=== Buttons in the GCS ===


To get buttons for the servo switch module in the GCS add settings_servo_switch.xml to the settings files of your aircraft.
To get buttons for the servo switch module in the GCS add conf/settings/modules/servo_switch.xml to the settings files of your aircraft.
 
[[Category:Modules]]

Latest revision as of 15:46, 29 August 2013

Modules
ArduIMU
Module/ADC generic
Module/Aeroprobe OTF
Module/Airspeed ETS
Module/AOA adc
Module/Bosch BMP085
Module/collective tracking control
Module/FlightBenchmark
Module/Freescale MPL3115A2
Module/GPS UBlox UCenter
Module/guidance vector field
Module/Honeywell HIH-4030
Module/Hygrosens TEMOD-I2C-R1
Module/infrared
Module/IST DigiPicco
Module/LM75
Module/Mag HMC58xx
Module/Meas Spec MS5611 I2C
Module/Melexis MLX90614
Module/rl obstacle avoidance
Module/Rotorcraft cam
Module/Sensirion SHT25
Module/Sensirion SHT75
Module/Servo switch
Module/System monitor
Module/TI TMP102
Module/TronSens HTM B71
Module/VTI SCP1000 I2C
Module/VTI SCP1000 SPI
Modules
Modules list
MultiUAV
Openlog
Pan Tilt Camera
SDLogger SPI Direct
Sensors/AMSYS

This module allows you to easily control a servo output like a switch (e.g. for a hatch, cam trigger, etc) via Flight Plan and GCS (not via RC!).

To use it load the servo_switch module:

File: conf/airframes/myplane.xml 
  <modules>
    ...
    <load name="servo_switch.xml"/>
  </modules>

Now you only have to declare a servo in your airframe.xml that you want to use.

By default the servo_switch module looks for a servo called SWITCH. The switch on value is 2000us and switch off is 1000us by default. e.g. in my airframe file I have:

File: conf/airframes/myplane.xml 
  <servos>
    ....
    <servo name="SWITCH" no="7" min="1000" neutral="1500" max="2000"/>
  </servos>

If you want to use a different servo/values you can set that in the modules section, e.g. for a servo named HATCH:

File: conf/airframes/myplane.xml 
  <modules>
    <load name="servo_switch.xml">
      <define name="SERVO_SWITCH_ON_VALUE"  value="1100"/>
      <define name="SERVO_SWITCH_OFF_VALUE" value="1900"/>
      <define name="SERVO_SWITCH_SERVO"     value="HATCH"/>
   </load>
  </modules>

Of course you only have to set these parameters here If you do not want to use the DEFAULT servo (SWITCH) or the default on/off values. Switch value will not go outside the range defined on the servo

Calling from Flight Plan

In your flight plan you just call the macro defined in servo_switch.h 

<call fun="ServoSwitchOn()"/>

or 

<call fun="ServoSwitchOff()"/>

respectively.

Buttons in the GCS

To get buttons for the servo switch module in the GCS add conf/settings/modules/servo_switch.xml to the settings files of your aircraft.

Retrieved from "http://wiki.paparazziuav.org/w/index.php?title=Module/Servo_switch&oldid=15802"