Search results

* STMicroelectronics STM32F429ZIT6 Cortex M4 MCU, up to 168Mhz with floating point unit (FPU), 256 KB external SDRAM with 64 ...ard STLinkv2 with SWD header (capable of programming itself or an external MCU)

...ilt in Bremen based on Tiny 1.3 and Tiny 2.2 hardware. It uses like booz a mcu and sensor pcb.

It uses like booz a mcu and sensor pcb. The sensor pcb has same extensions to the booz pcb: tempera Image:mcu_up.jpg|MCU Top

Connect the ST-Link to the MCU. ...et. To program a external MCU, remove CN3 jumpers and connect the external MCU with the SWD header.

== MCU or not MCU == NeoFromMatrix: Maybe we could use a MCU with more IO (like the discovery board) and 0805 (or bigger) parts.

* Dual-MCU architecture with dedicated radio/power management SoC for advanced applica * STM32F405 main application MCU (Cortex-M4, 168MHz, 192kb SRAM, 1Mb flash)

...er/sw/airborne/mcu_periph sw/airborne/mcu_periph] : interfaces/drivers for MCU peripherals like I2C, SPI, ADC, etc... (the HAL) ...tem), others do not need this (for example a new set of control loops). An MCU peripheral uses on-chip hardware peripherals in the main microcontroller (s

* MCU: STM32F411CEU6 (100MHZ, 512K FLASH) * Onboard 4in1 ESC MCU EFM8BB21

* STMicroelectronics STM32F4VGT6 Cortex M4 MCU, up to 168Mhz with floating point unit (FPU), 192 KB RAM, 1024 KB Flash ...board STLinkv2 with SWD header (capable of programming onboard or external MCU)

...%"|''Name''!!width="10%"|''Type''!!width="10%"|''MCU Port''!!width="15%"|''MCU Resource''!!''Description'' ...%"|''Name''!!width="10%"|''Type''!!width="10%"|''MCU Port''!!width="15%"|''MCU Resource''!!''Description''

...%"|''Name''!!width="10%"|''Type''!!width="10%"|''MCU Port''!!width="15%"|''MCU Resource''!!''Description'' ...%"|''Name''!!width="10%"|''Type''!!width="10%"|''MCU Port''!!width="15%"|''MCU Resource''!!''Description''

#STM32F405RGT6 MCU with 192KB RAM and 1024KB flash. ...Just solder some wires on the solder pads to access JTAG/SWD of the STM32 MCU.

* ARM Cortex-M4 168MHz MCU * SD card logging on both MCU and Intel Edison

The CricketProbe is a programming and debugging tool for ARM Cortex MCU, based on the [http://www.blacksphere.co.nz Black Sphere Technologies] [htt The Lyorak probe is a programming and debugging tool for ARM Cortex MCU, based on the [http://www.blacksphere.co.nz/main/blackmagic Black Magic Pro

...quire receiver modification, one pin of the R/C connector is routed to the MCU UART5 receive input through a '''controlled inverter'''.<br> ...tor''' ("5Vaux",#2) '''can be switched ON and OFF''' on demand using APSW (MCU GPIO output PB12).

* 1 Atmel MEGA128 MCU

* mcu with fpu (e.g. stm32f4)

* '''XBEE modem''' holder <small>''(ASSO and Reset connected to MCU GPIOs)''</small> ...("5V Comp.",#2) '''can be switched ON and OFF''' on demand using EN_COMP (MCU GPIO output PC04).

...quire receiver modification, one pin of the R/C connector is routed to the MCU UART2 receive input through a '''controlled inverter'''.<br> ...tor''' ("5Vaux",#2) '''can be switched ON and OFF''' on demand using APSW (MCU GPIO output PB12).

* 72MHz 32bit ARM Cortex M3 MCU with 16KB RAM and 512KB Flash

* Single LPC2148 MCU |6||RESET||IN||External Reset - A LOW on this pin performs a MCU hardware reset||

||1 ||LPC2148 ||LPC2148 ||MCU ||Philips ||LPC2148FBD64-S ||DK 568-1765-ND

=== MCU === https://my.st.com/public/STe2ecommunities/mcu/Lists/ARM%20CortexM3%20STM32/Flat.aspx?RootFolder=https%3a%2f%2fmy.st.com%2

...omous code error, the aircraft may be saved via manual control and the fbw MCU.

Some newer ESC are build with a Silicon Labs MCU with a Intel 8051 core. <br/> * [http://www.silabs.com/products/mcu/Pages/ToolStick.aspx Silicon Labs Toolstick] available at [http://at.mouser

...Voltage reference for the ADC (will be 3.3V in most cases, can be found in mcu/adc datasheet) *R1 - Resistor between battery and ADC input pin of MCU

* Single [[MCU|LPC2148 MCU]]

...ery boards provide one onboard) with [[STLink| st-flash]] onto the criquet MCU:

...moved and this pin makes room for a RC receiver. Reason to have a separate MCU for RC and not bog down the mail AP loop with build in SPI receiver message

* In some cases you may not be able to access some memory areas in the mcu, in that case you should try:

Lisa/M is based on the 64 pins STM32F105RCT6 [http://www.st.com/internet/mcu/product/221023.jsp connectivity line family] processor featuring 64k of RAM ...of RAM and 512k of FLASH, which is part of the [http://www.st.com/internet/mcu/product/164485.jsp high-density performance line family].

...autopilot typically runs an RTOS or bare-metal on a small microcontroller (MCU), such as [[Lisa/M]] or [[Pixhawk]] and has limited memory and computationa

:* no MCU => no software or firmware req.

* Single [http://www.standardics.nxp.com/products/lpc2000/lpc214x LPC2148 MCU] :: On the Tiny v2.1 design GPS reset is connected to a GPIO pin on the MCU and allow the operator to reset the GPS as needed.

* NXP [http://www.standardics.nxp.com/products/lpc2000/lpc214x LPC2148] MCU based

Lisa/M is based on the 64 pins STM32F105RCT6 [http://www.st.com/internet/mcu/product/221023.jsp connectivity line family] processor featuring 64k of RAM ...of RAM and 512k of FLASH, which is part of the [http://www.st.com/internet/mcu/product/164485.jsp high-density performance line family].

* NXP [http://www.standardics.nxp.com/products/lpc2000/lpc214x LPC2148] MCU based

* NXP [http://www.standardics.nxp.com/products/lpc2000/lpc214x LPC2148] MCU based

so it can compile and upload ESP8266 code to the ESP8266 mcu.