Search results

./configure --enable-libraries --enable-shared --prefix=/opt/jsbsim ...ld system will first try to find JSBSim via pkg-config and fall back to ''/opt/jsbsim''.

...ipt to right location: <source lang="bash">sudo mv ~/Desktop/pprz-env-set /opt/paparazzi/bin/pprz-env-set</source> ## Change script permissions: <source lang="bash">sudo chmod 755 /opt/paparazzi/bin/pprz-env-set</source>

$ cd /opt $ exportline="PATH=$PATH:/opt/stlink"

--opt PING,SETTING,GUIDED_SETPOINT_NED,REMOTE_GPS_LOCAL --opt ATTITUDE,GPS,PPRZ_MODE,DESIRED,COMMANDS,ACTUATORS,ROTORCRAFT_FP,IMU_GYRO,IM

cd /opt/vc/src/hello_pi/libs/ilclient

$ sudo ln -s /opt/jsbsim/lib/libJSBSim.so.0 /usr/lib # mkdir -p /opt/ivy-c

$ make ground_segment.opt ...it/gcs.opt'' and ''sw/ground_segment/tmtc/server.opt'' instead of the non-opt versions.

#:<pre>/opt/paparazzi/arm-multilib/bin/arm-none-eabi-gdb var/<airframe>/ap/ap.elf</pre> #:<pre>/opt/paparazzi/arm-multilib/bin/arm-none-eabi-gdb ./var/AIRFRAME/ap/ap.elf</pre>

sudo tar -vjxf gcc-arm-none-eabi-4_7-2013q2-20130614-linux.tar.bz2 -C /opt exportline="PATH=$PATH:/opt/gcc-arm-none-eabi-4_7-2013q2/bin"

...ll be fixed in the next version, change ft2232_device_desc to "Lisa/L" in /opt/paparazzi/stm32/share/openocd/scripts/interface/openocd-lisa-jtag.cfg : CFLAGS += -O$(OPT) -march=armv7-a -mtune=cortex-a8 -mfpu=vfp -mfloat-abi=softfp

...ace a tiny amount of solder on the pads on the bottom of the motor adaptor opt PCB where it connects to the Lisa/S. Tip use a solder sucker to suck most o ...e tiny little joint. You might like to ponder as I did on your decision to opt for the pre soldered kit...

* If you did not install the jsbsim package your JSBSim installation under /opt/jsbsim will be used and you will have to set your library path (either in y LD_LIBRARY_PATH=/opt/jsbsim/lib ./var/Quad_LisaM_2/nps/simsitl --fg_host 127.0.0.1

...manually have to install a recent version of libopencm3 (for example into /opt/libopencm3) in order to build luftboot. The libopencm3 from the paparazzi-a

<source lang="bash">export PKG_CONFIG_PATH=/opt/X11/lib/pkgconfig</source> Run /opt/local/bin/switch2 to select a different theme.

|[[User:Opt|Opt]] | [[User:Opt|Opt]] || Berlin, Germany || ARDrone, Lisa/M Quadrotor ||| 2011 || First flights

...arious hardware suppliers. The cable design is also open source, you could opt to make one yourself, but that is not trivial.</s>

...-opensource/sources/linux-3.4.11/linux-3.4.11/ -j8 ARCH=arm CROSS_COMPILE=/opt/extra/CodeSourcery/Sourcery_CodeBench_Lite_for_ARM_GNU_Linux/bin/arm-none-l

Testing code is specifically for UAS of utmost importance. To test we could opt to make small cases in Testlink for everyone to try and report the outcome.

$ make opt

The toolchain will be installed in your file system in '''/opt/arm-2012.03''' directory. Then you need to tell which compiler should be us <configure name="PREFIX" value="/opt/arm-2012.03/bin/arm-none-linux-gnueabi"/>