Search results

• Module/AOA adc
  == Airframe Adjustments == * (1) '''Insert''' the software module in the airframe:
  2 KB (302 words) - 03:28, 28 November 2017
• Sensors/AMSYS
  ==Airframe== This is an expample to define the module in the airframe.
  2 KB (362 words) - 09:18, 30 June 2015
• CSUBlog
  ...age to hold everything. The second Paparazzi autopilot was received and an airframe file has been started for the new plane. (Nick)
  429 bytes (70 words) - 18:21, 9 March 2011
• Explorer/PPRZ
  airframe file: <!DOCTYPE airframe SYSTEM "../../airframe.dtd">
  7 KB (875 words) - 05:41, 29 September 2020
• User:Rbdavison
  : Several Manual flights to trim the airframe and configuration. Build a bigger airframe with hours of endurance instead of minutes.
  1 KB (207 words) - 04:44, 16 November 2009

• File:Proj mentor 1.zip ** Our Airframe (110 KB) - 04:15, 8 January 2014

• Gyroscopes/ADXRS613
  Now that the gyro board can be physically interfaced with the PPZ, the airframe file must be updated. Add the following lines to the Makefile portion of the airframe file to include the gyro code:
  6 KB (1,018 words) - 19:17, 9 March 2011
• Module/FlightBenchmark
  ==Airframe Adjustments== <li>Insert the software module in the airframe:
  4 KB (537 words) - 14:57, 7 March 2012
• OLSR
  === Airframe configuration === ...ly do by adding to your firmware section the following instructions (in an airframe based on ardrone2_raw.xml for instance):
  2 KB (388 words) - 06:50, 15 April 2015
• User:CSU-FCUAV
  Airframe: Hobby Lobyy Senior Telemaster ARF Airframe: [[CSU_Telemaster]]
  4 KB (620 words) - 08:45, 3 August 2010
• User:TimHansen
  It is necessary to modify the airframe config-file ("-DGPS_USE_LATLONG") [[Airframe_Configuration#GPS]] In the newer Airframe Config File this has to be:
  2 KB (269 words) - 03:00, 6 April 2012
• Lisa/S
  MOT1 (DC) = SERVO3 (PWM) = nb 0 (airframe) MOT2 (DC) = SERVO4 (PWM) = nb 1 (airframe)
  4 KB (652 words) - 04:24, 28 November 2017
• CSU Telemaster
  <!DOCTYPE airframe SYSTEM "airframe.dtd"> <airframe name="Telemaster">
  9 KB (1,182 words) - 18:21, 9 March 2011
• Bixler
  The HobbyKing Bixler is a very inexpensive airframe with very easy flight characteristics and reasonable payload capacity. Its == Airframe configuration ==
  3 KB (577 words) - 23:14, 20 July 2020
• Subsystems
  ...me_Configuration#Firmware_and_Hardware_definitions|firmware section of the airframe file]]. ....8''' it is possible to safely replace ''subsystem'' by ''module'' in your airframe file. The roadmap of Paparazzi is to convert existing subsystems to [[modul
  4 KB (547 words) - 03:45, 29 November 2021
• NoVa
  === Airframe ===
  3 KB (488 words) - 13:52, 10 March 2011
• SUMO/sw configuration
  ...ile. It describes the sub-configuration files that are responsible for the airframe, the RC transmitter (radio), the telemetry messages/rate, the settings poss airframe="airframes/logger_sd.xml"
  1 KB (167 words) - 01:47, 20 August 2013
• Beginners Tips
  The airframe file needs to be altered to use the right serial ports. You usually want to use the ap build target. However, the default airframe files need to be tweaked for your modem baud rates and tiny model.
  3 KB (582 words) - 18:09, 9 March 2011
• Units
  ...e is converted to <tt>code_unit</tt> and then written to the <tt>generated/airframe.h</tt> file ...d(x)</tt> macros and converts it to the correct unit when reading from the airframe file. When saving the new value it will be correctly written without that m
  3 KB (435 words) - 03:21, 28 November 2017
• Here
  In Paparazzi center in addition to your airframe file, flight plan you'll want to select the "tuning_ins.xml" settings file.
  1,001 bytes (180 words) - 22:01, 30 July 2011

View (previous 20 | next 20) (20 | 50 | 100 | 250 | 500)