Installation/Linux

Installation

Installation

Installation/BeagleBoneBlack

Installation/FromScratch

Installation/Linux

Installation/MacOSX

Installation/Windows10

This page only describes the installation of the prerequisite tools and dependencies on Debian/Ubuntu needed for Paparazzi.

See the general Installation page for how to download Paparazzi and launching it after you followed the instructions here.

Introduction

Paparazzi is very easily installed on any laptop or workstation running Ubuntu, Debian (or any of their derivatives).

The steps required to install the software needed to be able to let your UAS fly

• Install the basic Paparazzi dependencies and the ARM cross compiling toolchain.
• Download the source code from the source repository.
• Allow access to your PC hardware connection by adding appropriate Udev rules.
• Compile the binaries from the sources and launch the software.

Users of other Linux flavors than a recent Ubuntu or Debian and anyone needing manual control of each individual package can install them independently.

For the impatient

For Ubuntu add the paparazzi-uav ppa sudo add-apt-repository ppa:paparazzi-uav/ppa and install the paparazzi-dev package.

Since Paparazzi v5.0 the gcc-arm-embedded toolchain is recommended. Available as of Ubuntu 14.04, on older versions it can be installed via tarball.

Or just use the Quickstart for Ubuntu 12.04 LTS.

Installation video Tutorials

EmbedVideo does not recognize the video service "youtubehd".

EmbedVideo does not recognize the video service "youtubehd".

Installation of dependencies

Ubuntu

Add the installation sources for the Paparazzi software packages. Run from a terminal:

sudo add-apt-repository ppa:paparazzi-uav/ppa

Then update the systems package inventory and install the main Paparazzi software dependencies. This will take some time.

sudo apt-get update 
sudo apt-get install paparazzi-dev

Debian

For Debian Squeeze (6.0) and Wheezy (7.0) packages are built using the Open Build Service (OBS) on OpenSUSE Build Service project home:flixr:paparazzi-uav

First add the key:

wget -q "http://download.opensuse.org/repositories/home:/flixr:/paparazzi-uav/Debian_7.0/Release.key" -O- | apt-key add -

Add the appropriate repo, depending on your Debian version to sources.list

echo "deb http://download.opensuse.org/repositories/home:/flixr:/paparazzi-uav/Debian_6.0/ ./" | tee -a /etc/apt/sources.list
echo "deb http://download.opensuse.org/repositories/home:/flixr:/paparazzi-uav/Debian_7.0/ ./" | tee -a /etc/apt/sources.list

Update the systems package inventory and install the main Paparazzi software dependencies.

sudo apt-get update 
sudo apt-get install paparazzi-dev

ARM embedded toolchain

For current Paparazzi versions (v5.0 and above) the gcc-arm-embedded toolchain is recommended, which also supports the STM32F4 with FPU (hardware floating point).

The most common way is to download and unpack the tarball and add it to your PATH:

The Pixhawk Devs have mentioned the 4.8 as buggy.

cd ~
wget https://launchpad.net/gcc-arm-embedded/4.7/4.7-2013-q2-update/+download/gcc-arm-none-eabi-4_7-2013q2-20130614-linux.tar.bz2
tar -vjxf gcc-arm-none-eabi-4_7-2013q2-20130614-linux.tar.bz2 -C /opt
rm -r gcc-arm-none-eabi-4_7-2013q2-20130614-linux.tar.bz2
exportline="PATH=$PATH:/opt/gcc-arm-none-eabi-4_7-2013q2/bin"
if grep -Fxq "$exportline" ~/.profile; then echo nothing to do ; else echo $exportline >> ~/.profile; fi
source ~/.profile

The file .profile will be sourced in every bash after logging out and in again. Until then,

source ~/.profile

can be used for every bash individually.

If you can not access your toolchain with PATH working, look a the Installation/Linux#Troubleshooting.

gcc-arm-none-eabi as Debian/Ubuntu package

Note that there are actually two different toolchains available that unfortunately have the same package name!

• ARM gcc-arm-embedded toolchain
  • includes libstdc++ and newlib-nano
• Debian gcc-arm-none-eabi toolchain
  • does not include libstdc++
  • does not include newlib-nano

Both toolchains should work for most use-cases (if you don't need C++ or nano specs), although the ARM gcc-arm-embedded toolchain is better tested.

gcc-arm-embedded toolchain

On most Ubuntu versions (currently lucid, precise, raring, saucy and trusty) the gcc-arm-embedded toolchain can be installed as a debian package from the ppa:

sudo add-apt-repository ppa:terry.guo/gcc-arm-embedded
sudo apt-get update
sudo apt-get install gcc-arm-none-eabi

Note bug1309060 on Ubuntu 14.04 you have to explicitly install the gcc-arm-embedded version. You can list the available versions with apt-cache policy gcc-arm-none-eabi

sudo apt-get remove binutils-arm-none-eabi gcc-arm-none-eabi
sudo apt-get install gcc-arm-none-eabi=4-8-2014q2-0trusty9

gcc-arm-none-eabi Debian toolchain

Debian testing (jessie) and Ubuntu 14.04 (trusty) have the gcc-arm-none-eabi package in the official repositories (universe), and can be installed with:

sudo apt-get update
sudo apt-get install gcc-arm-none-eabi

Old toolchain for Paparazzi v4.x and earlier

For Paparazzi v4.x and earlier you need to install the paparazzi-arm-multilib package. It has support for both ARM7 (i.e. Tiny,TWOG,YAPA autopilot boards) as well as STM32F1 (i.e. LISA boards).
This toolchain does not properly support STM32F4 based autopilots!!

You can install it explicitly with:

sudo apt-get install paparazzi-arm-multilib

Optional Packages

The packages lpc21isp and openocd are normally automatically installed as they are recommended packages of paparazzi-dev, if not you can manually install them via:

sudo apt-get install lpc21isp openocd

lpc21isp is needed to serially flash the LPC2148 based autopilots (e.g. bootloader for tiny, twog, umarim), openocd is for flashing via JTAG (e.g. for Lisa boards) and debugging.

Installing and running Paparazzi

Please see Getting the Source Code on the general Installation page for details on downloading the Paparazzi source code, compiling and running it.

Udev rules

Add the appropriate Udev rule (available in fhe file 50-paparazzi.rules) to the USB handler. Simply copy as root conf/system/udev/rules/50-paparazzi.rules to /etc/udev/rules.d/, e.g in a terminal:

cd <your paparazzi directory>
sudo cp conf/system/udev/rules/50-paparazzi.rules /etc/udev/rules.d/

See the Udev page for more details.

Troubleshooting

No access rights for USB devices

Some Linux distributions, don't allow standard (non admin) users to directly access the USB bus by default. On recent Ubuntu/Debian versions the first/main user is already a member of the plugdev group which should be sufficient for most cases.
If you have problems, make yourself a member of the plugdev and dialout groups:

sudo adduser <your login> plugdev
sudo adduser <your login> dialout

Logout and login again.

arm-none-eabi-gcc: Command not found

Appeared on Debian Wheezy 7 (gcc-arm-none-eabi-4_8-2013q4 installed via tarball)
If this error occurs, maybe the ia32-libs are missing.

Enable multiarch and install ia32-libs:

dpkg --add-architecture i386
apt-get update
apt-get install ia32-libs

arm-none-eabi-gdb: error with libncurses.so.5

Appeared on Xubuntu 14.04 LTS (gcc-arm-none-eabi-4_8-2013q4 installed via tarball)
Terminal output: arm-none-eabi-gdb: error while loading shared libraries: libncurses.so.5: cannot open shared object file: No such file or directory

If this error occours, maybe lib32ncurses5 is missing.
Found on launchpad q&a

FTDI serial adapter not working on old Ubuntu version

On older Linux distributions (not needed for lucid and later), the Braille TTY driver interferes with FTDI USB Serial adapters. If somehow your FTDI serial adapter does not work, remove the package via:

sudo apt-get remove brltty

Code not starting on autopilot after changing gcc

If you changed the toolchain (e.g. installed a new one for having FPU-Support for the F4), you need to run

make clean && make

in sw/ext in order to rebuild the libs. Otherwise the embedded code can behave strange (most likely not start)