Lisa/M/Tutorial/RotorCraft

Airframe Setup

Basically rotorcraft is an aircraft that uses propeller lift to hold itself floating. There are many types of rotorcrafts, but there are a couple of global classes:

Single rotor (helicopters) which divide into:

• Classic (with tail rotor);
• Co-axial (with two sets of counter rotating blades);
• All others (there are some other helis like Chinhook or Osprey).

Multirotor (copters) which are:

• 3 rotor Y type - this copter maintains yaw by tilting one of it's rotors with servo;
• 4 rotor X or + type - the trick is that two rotors spin "forward" and other two "backward", with some strong magic difference between spin rates is used to rotate the craft around. X and + types differ only with direction of movement: X moves with two rotors forward and + moves with one rotor, like this +>;
• 6 rotor * or Y type - first case is the same as 4 rotor with two additional arms, the other is virtually one 3Y rotor flipped and put under another 3Y rotor;
• 8 rotor *, V or X/+ type - first is 6* rotor + two more arms, second is like Asctech Falcon 8 and the third is 4X/+ type put one on another.

And if first class of rotorcrafts can use gyros only for yaw stabilization, multirotors need 3D (three axial) gyros to stabilize itself hovering which by the way do not guarantee that craft holds the spot, just not letting it fall on side.

First Steps

Multirotors

Firstly you should choose correct airframe. If you're novice to copters quadrotor will be a good choice for several reasons: firstly it's most common type of copter, then most of hardware works with such setup "out of the box" and there is plenty information in mailing lists. By the way, it would be a good idea to decide how do you want to use your copter. Generally it will allow you to choose correct motors and ESCs for copter.

ESC and motors should be chosen with weight economy in mind. i.e. good idea is to purchase ~600-1000 gram motors (NOT more unless you know what are you doing) and 15-25A ESCs depending on your motor current consumption.

Airframe typically consists of "center hub" and "rotor arms" which due to ease of aircraft control and low crushablity are made of light materials (for example aluminum for arms and perforated carbon for center hub). There is a wide choice of ready to build aftermarket airframes if you don't want to bother with building one.

Generally there is only one important thing left it's balancing whole copter after you put it together. There is one simple rule: ready to fly quadrotor should have it's center of gravity (COG) in the middle. By "ready to fly" I mean - every equipment that should be placed on copter including battery and payload.

Configure the autopilot

Generally: Rotorcraft_Configuration

Partlists

I recognized that I spent a lot of time to search all compatible components. That list should help you to make your chose easier and faster.

User	Type	Propeller size	Frame	Motors	ESC	Telemetry	RC Transmitter	RC Receiver	GPS	Autopilot	IMU
Bruzzlee	Quadrotor	12"	Homebrew	Scorpion S-2215-900KV	ePower 30A 2-4S	Xbee 60mW	Spektrum DX6i	HobbyKing Orange Satellite	GS407	Lisa/M	Aspirin
add your list here

Xbee

Xbee parts photo

• 2.4GHz Duck Antenna RP-SMA - Large
• Interface Cable RP-SMA to U.FL (should fit to the Duck Antenna)
• XBee Explorer USB
• XBee Pro 60mW U.FL Connection - Series 1
• XBee Pro 60mW Wire Antenna - Series 1
• XBee Explorer Regulated

GPS GS407

• 50 Channel GS407 Helical GPS Receiver
• GS407 Breakout Board

Wiring (not tested!)

LisaM wiring for quadrotor

Alternative LisaM wiring for quadrotor

This scheme shows a possibility to connect the parts to the Lisa M.
In this version, the board is powered by the 5V BEC of the Servo 1 ESC.
Jumper J1 is bridged. The battery on I2C1/CAN is only needed to measure the actual battery voltage.

--> This version is not tested yet!!! No warranty!!! <---

See following links for more informations:
Lisa/M#Pinout
Lisa/M#Schematic
Lisa/M/Tutorial/FixedWing#RC_receiver
Lisa/M/Tutorial/FixedWing#Power

IMU calibration

Usually you get a calibration file from the supplier. If not you can calibrate you Aspirin IMU (or else) by following this Tutorial:
ImuCalibration

How you get your Local Magnetic Field values is written down here:
Subsystem/ahrs

Frame building

"Photo gallery" Bruzzlee: User/RotorCraft/Bruzzlee

---