Failsafe

Paparazzi has several built-in failsafe features ranging from lowlevel to highlevel and from implied to optional.

On the lowest level, precise timing of the transmitter pulses creates safety that goes beyond traditional switches enabling safer use of old RC equipment. On the highest level, the exceptions feature of the flight-plans allow for very flexible custom built failsafe features.

FBW (Fly By Wire)

'Failsafe Switch'

The lowest level of paparazzi is the FBW (Fly By Wire) controller that reads the RC, reads the autopilot commands and drives the servo's based on the lowlevel failsafe options.

This is the 'switch' between manual or automatic modes. Therefor there is no need for an other failsafe board. Indeed, the paparazzi FBW has evolved with so much intelligence that it is certainly safer than some and probably at least as safe as any other failsafe switches. This is amongst others (besides the highlevel validated code, separated process, ...) because paparazzi FBW unlike generic switches is given precise remote control information in it's RC.xml. If you use a wrong type of transmitter (e.g. not the right amount of channels, or not the correct interval or sync pulse length) than even when on the same frequency the FBW will not listen to the commands. Also, when 2 transmitters should be on the same frequency, then the chance of both signals together still being read as valid is very small. (This does NOT mean you can fly with 2 planes on the same frequency however. This only means that in this catastrophic scenario paparazzi does a pretty good job in delaying disaster from happening. )

 * be aware that there exist many failsafe switches that use a pulse of the RC (e.g. channel 5) to switch 
   between autopilot or RC. When using analog RC equipment or any equipment that does not have correctly 
   programmed failsafe servo values this is very unsafe as whenever the RC is out of range the switch will 
   start switching back and forth putting the UAV out of control even if the autpilot is perfectly OK.

FBW logic

-RC GOOD: listen to the MODE switch on the Transmitter  
 (this means whenever the remote control is close enough the pilot has the final word)
-RC BAD: go to automatic mode (see further on for handling of automatic modes)
-RC BAD AND AUTOPILOT DATA TIMEOUT: failsafe command values from airframe configuration XML 
 (do not omit to fill in useful failsafe values in the command section; usually slight pitch up for minimal speed, 
 ailerons neutral in order not to roll inverted and off coarse throttle down: it is not recommended to try to make 
 turns here with aileron deflections. A small rudder deflection on the other hand is recommended when available  )

AP (AutoPilot)

Home mode

The HOME mode is a failsafe mode where the standard navigation (own flightplan) is suspended and the aircraft flies a circle around the HOME waypoint at a safe altitude (security_height attribute in your flight-plan). This mode is triggered on different events. Leaving this mode is done by clicking on the red HOME text in the GCS.

Too far from HOME

Home mode is triggered if the distance to the HOME waypoint is greater than a threshold (max_dist_from_home attribute) set in the fight-plan (displayed as a circle on the GCS map).

RC link failure while manual or AUTO1

Home mode is triggered if RC uplink is lost in MANUAL or AUTO 1 modes.

• When MANUAL the manual mode is restored as soon as RC link is restored as expected.
• However: In AUTO 1 mode, one must manually leave the HOME mode using the GCS

! Word of caution with respect to AUTO1: When flying auto1 with a lot of RC interference (which is not recommended anyway), be prepared that the plane might enter HOME mode. Also, do not be tempted to fly far away in auto1 mode (possibly out of RC range) without a fully tuned auto2 autopilot or sufficient visual contact to allow manual control. As soon as you are so far that RC packets get lost, paparazzi will switch to HOME and will stay in HOME until you choose MANUAL of re-enable AUTO1 on the GCS !

Setting RC lost mode

By default when RC is lost (in Manual or Auto1) HOME mode is triggered, you can change this behaviour by setting the RC_LOST_MODE:

 <define name="RC_LOST_MODE" value="PPRZ_MODE_AUTO2"/>

In this example RC_LOST_MODE is set to AUTO2, which can be useful if you experience glitches on your RC on the mode channel and want the aircraft to continue the mission instead of triggering HOME mode. BUT only use this if you have AUTO2 navigation set up properly and everything is initialized correctly!

You can disable HOME mode locking by adding the following line in your airframe file:

 <define name="UNLOCKED_HOME_MODE" value="TRUE"/>

Then you can restore from HOME mode using the RC and do not need to do this on the GCS if in AUTO1.

Caution: Use these two settings with care, as they might deteriorate the failsafe security of your aircraft.

Kill mode

In this mode the throttle is killed (this is the default mode when switching on the autopilot). You can enter this mode manually with the kill button (with confirmation). Kill mode is also triggered in the following cases:

Catastrophic battery level

If the battery level goes under the catastrophic low level (defined in the airframe file)

Way too far from HOME

The plane goes into kill mode if it is too far away from the HOME waypoint. You can configure this KILL_MODE_DISTANCE in your airframe file:

 <section name="MISC">
   ...
   <define name="KILL_MODE_DISTANCE" value="(1.5*MAX_DIST_FROM_HOME)"/>
   ...
 </section>

In this example it is set to 1.5 times the max_dist_from_home (attribute set in your flight plan).

GPS signal lost

In this mode, the autopilot uses the failsafe roll, pitch and throttle settings defined in the airframe file. It is recommended to disable throttle and make a shallow turn at low flight speed. When barometric information is available and compass heading information, it is recommended to disable this safety mode and train the GCS operator to bring the plane home on heading and altitude only.

Do not mix up the <commands> failsafe_value and the <section name="FAILSAFE" prefix="FAILSAFE_"> default values. The first result in fixed servo positions with the plane totally out of control, while the latter still involve the innerloop to stabilize the plane.

Lost datalink communication (optional)

This can be done via the a flight-plan exception, e.g. go to the Standby block after 30 seconds:

 <exceptions>
   ...
   <exception cond="datalink_time > 30"  deroute="Standby"/>
 </exceptions>

You also need to include the datalink.h header file in the header section of your flight plan.

Outside mission boundary (optional)

Also use exceptions and/or function calls for this.

For an example see EMAV2009_safety.xml in the directory conf/flight_plans is an example of a safety procedure that can be included in other flight-plans. It uses two sectors defined in EMAV2009_data.xml, a smaller Green "soft boundary" and a hard boundary defined by the Red sector.

<procedure>
  <exceptions>
    <exception cond="Or(! InsideGreen(GetPosX(), GetPosY()), GetPosAlt() > ground_alt + 150)" deroute="Center"/>
  </exceptions>

  <blocks>
    <block name="Center" pre_call="if (!InsideRed(GetPosX(), GetPosY())) NavKillThrottle();">
      <circle wp="_CENTER" radius="DEFAULT_CIRCLE_RADIUS"/>
    </block>
  </blocks>

</procedure>

The first exception deroutes the plane to the Center block below it, if it is outside the Green sector or higher than 150m over ground. While in the Center block the statement in the pre_call function gets evaluated each time, if the plane is now also outside of the Red sector throttle is killed.