Search results

• Gallery
  Image:Minimav.jpg| <b>FJ1</b><br>The PPZUAV current project/ MAV 420mm / 85g
  8 KB (1,247 words) - 12:38, 2 September 2014
• SUMO
  ...[[Get_Hardware|get hardware]] section for a source of these parts. In the current version of the SUMO we use the Umarim Lite v2 autopilot, a TWOG board as da
  7 KB (1,025 words) - 15:51, 19 December 2019
• Installation/MacOSX
  '''(Feb. 1, 2014) Current OS X limitations:''' ...es that might work on older OS X versions but are known not to work on the current Mac OS X. They all can be found on the [[Installation/MacOSX-legacy]] page.
  18 KB (2,727 words) - 08:24, 25 February 2019
• Working with INDI
  ...timate the control effectiveness values online. It does this by taking the current estimate of the control effectiveness multiplied with the most recent chang
  13 KB (1,966 words) - 16:24, 24 October 2020
• Dev/Caspa
  In the current stage we achieved full duplex SPI communication between the Overo and the S
  15 KB (2,331 words) - 05:44, 12 October 2011
• AirborneCodeReorg
  The current airborne sourcecode has gone a little bit out of control. Everyone was work
  10 KB (1,520 words) - 11:16, 18 March 2013
• Mission computer
  # Mission Planner checks whether the area can be surveyed with the current resources (remaining battery, flight speed, ...)
  12 KB (1,845 words) - 13:57, 27 November 2017
• Failsafe
  Zero roll/pitch and current heading setpoint (so hover in attitude mode but not position controlled) an
  11 KB (1,873 words) - 16:29, 30 April 2015
• MeekPE PPM Encoder Board
  |v1.00 (current)||08/2010||0603/TSSOP PCB design
  9 KB (1,393 words) - 11:55, 14 December 2012
• STM32F4 Discovery
  |JP1||JP1||Switch||MCU Current can be measured here
  12 KB (1,840 words) - 13:21, 3 May 2015
• Booz/Autopilot
  <li>Power on (~5v to 12v current limited power supply suggested)
  10 KB (1,470 words) - 18:43, 1 April 2012
• Lisa/M v2.0
  ...g in potential thermal shutdown while in flight. Depending on the expected current draw, it is best to power this regulator with a lower voltage. 5V is the pe ...f, for example, one is using an external 5V regulated supply, and a higher current is needed. Unless external use of 5V is required on the ANALOG1 and ANALOG2
  39 KB (6,235 words) - 06:23, 21 February 2020
• Installation/MacOSX-legacy
  This will only be active in the current terminal session. If you wish to manually modify the path permanently, you
  19 KB (3,014 words) - 09:55, 10 June 2016
• TWOG/v1.0
  |1||TPS2051BDBV||TPS2051B||IC4||Current Limited Power Distribution Switch||Texas Instr.||SOT23-5||''yes''||296-2126
  15 KB (2,149 words) - 09:46, 2 March 2012
• Dev/LisaL
  ...gpio's used for servos burnt through when connected directly to servos. - Current solution: resistors (Esden)</strike>
  13 KB (2,118 words) - 11:16, 18 March 2013
• Apogee/v1.00
  The internal switch TPS2051B is designed to withstand 500mA continuous current and is '''short-circuit and thermally protected'''.<br>
  16 KB (2,357 words) - 07:22, 2 August 2018
• Lisa/M v1.0
  ...g in potential thermal shutdown while in flight. Depending on the expected current draw, it is best to power this regulator with a lower voltage. 5V is the pe
  19 KB (2,935 words) - 19:15, 2 August 2013
• Bebop
  To use the driver in current firmware OTG serving should be off. [[use_the_USB_port_on_Parrot_Drones|Tak
  14 KB (2,164 words) - 11:25, 28 September 2022
• AR Drone 2
  Replace the current AR.Drone 2.0 brain by uploading paparazzi in current ARM chip and use the aready available sensors. Connect a GPS on the USB por
  66 KB (9,457 words) - 06:23, 8 September 2017
• RC Receivers and Radios
  ...e C stands for '''C'''ombined, the PPM sum stream output, supported on all current autopilot boards,
  27 KB (4,532 words) - 03:05, 3 August 2017

View (previous 20 | next 20) (20 | 50 | 100 | 250 | 500)