DevGuide/GDB OpenOCD Debug

JTAG adapters

Recently some new JTAG adapters that use the FTDI2232 USB-parallel converter were introduced through OpenOCD (you can try your Wiggler with that, too). USB JTAG adapters include Floss-JTAG, Olimex or Amontec and also fine with Windows (Yagarto).

Also see DevGuide/OpenOCD for installation and configuration instructions.

Debugging with GDB over JTAG

Procedure

1. Start openocd in a new shell since this process needs to remain running.

   To connect to the Lisa/L board run the command

   openocd -f interface/lisa-l.cfg -f board/lisa-l.cfg

   To connect to the Lisa/M board via FLOSS-JTAG run the command:

   openocd -f interface/flossjtag.cfg -f board/lisa-l.cfg

1. Start GDB with an argument of the elf file created and uploaded to the board.

   If you programmed with the ap target then the command would be along the lines of

   /opt/paparazzi/arm-multilib/bin/arm-none-eabi-gdb var/<airframe>/ap/ap.elf

   Replace <airframe> with the name of the airframe that has been built.

2. Now connect GDB to the board

   target remote localhost:3333

3. Now we need to set some break points in the code.

   In this example the ap target was part of the rotorcraft and main.c contains the main program. Open rotorcraft sw/airborne/firmwares/rotorcraft/main.c and find a line at which you'd like to set a break point.

   break main.c:113

4. Stop the currently running code

   monitor reset halt

5. Reset the code back to the start

   monitor reset init

6. Now we can run the program which will stop at the break point we set.

   continue

Black Magic Probe

1. Start GDB for arm

   Open GDB with the correct binary file

   /opt/paparazzi/arm-multilib/bin/arm-none-eabi-gdb ./var/AIRFRAME/ap/ap.elf

   Set Black Magic Probe as Target over the serial link (see ls /dev/ttyACM*):

   target extended-remote /dev/ttyACM0

   Probe via JTAG to get a list of devices:

   mon jtag_scan

   Attach to a device:

   attach 1

2. Happy Debugging!

-this information was merged from: --ht tp :// sourceforge. net/apps/mediawiki/blackmagicdebug/index.php?title=Main_Page --JTAG

Useful commands

• We probably want to ignore the interrupt calls for the moment so we can step through the code as it's being called. Note that we don't always want to do this. (STM32 command only)

  monitor cortex_m3 maskisr on

• A stack trace can be printed with the command

  bt

• show the variable of a variable

  print i2c1.status

• Show (eXamine) the value of the 9 bytes hardware register at address 0x40005800 and show them in hex format:

  x/9x 0x40005800

• In some cases you may not be able to access some memory areas in the mcu, in that case you should try:

  set mem inaccessible-by-default off

Commands can often be issued without typing the entire command. Here are some commonly used commands; many of them can be invoked using only the first letter:

(gdb) quit – exit the debugger
(gdb) file – load an executable file
(gdb) break line-number/function name -- Set a break-point on a line/at start of function
(gdb) run <args> -- start running the program; if there are command-line arguments, put them after the run invocation
(gdb) cont -- continue running, after a break
(gdb) next -- Next program line (step over function calls)
(gdb) step -- Step into function calls.
(gdb) finish - Step out of the present function
(gdb) print expression -- Show value of a variable or expression
(gdb) list – List 10 lines of the program being debugged. The sixth line is the preset statement. Subsequent, consecutive entry of list will list the next 10 lines.
(gdb) where – obtain a backtrace showing all function calls before the current statement
(gdb) up – Move to the function that called the present function. Useful if your program crashes in a library function; use up to get to the last function call in your program
(gdb) down – Reverses the action of up
(gdb) delete – Removes breakpoint by number (see example following). If no number, all deleted.
(gdb) kill – Terminates the program.

Setting up .gdbinit for BMP and gdb-regview

If you use gdb just with a BMP, you can set some initialization commands in ~/.gdbinit that will run when gdb is started, improving workflow.

A very useful plug-in called gdb-regview (available on GitHub) can really speedup debugging stm32 processors by providing a pretty-printed summary of register contents.

A sample file for debugging Lisa/M 2.0 would be:

set target-async on
set mem inaccessible-by-default off
#for gdb-regview plugin
source /path/to/gdb-regview/gdb-regview.py
regview load /path/to/gdb-regview/defs/STM32F10X_CL.xml
tar ext /dev/BMP_DEVICE
mon version
mon swdp_scan
att 1

This should be saved in ~/.gdbinit.

Then, after one starts gdb as described above, you can view registers easily, for example:

(gdb) regview show ADC_CR1

Easily load new binaries from inside gdb with BMP

It is also easy to rebuild and reload a program from inside gdb. Calling make from the gdb command line will call make in your current directory:

(gdb) make

To load a new elf file into gdb after compiling elsewhere (only required when changing the name of the file):

(gdb) file file_name.elf

To upload the binary as per the currently loaded elf:

(gdb) load

This assumes you have attached to the target already (as per the .gdbinit example just above).

To restart the program from the beginning:

(gdb) run

and enter y.

gdb should detect that the elf has changed when loading the new binary, so if the file name has not changed, one should just be able to rebuild (make from inside gdb if appropriate) and then call load and run.