Difference between revisions of "Data Logger"
| Line 15: | Line 15: | ||
To solve this issue, there are various loggers that can be connected to your Paparazzi Autopilot board. A short overview can be found on this page. | To solve this issue, there are various loggers that can be connected to your Paparazzi Autopilot board. A short overview can be found on this page. | ||
= Available Data logger options | =Available Data logger options= | ||
== | ==[[twoga-Logga|TWOGA-Logga]]== | ||
==[[twoglogdedicated|An dedicated TWOG board for logging]]== | |||
[[ | |||
= | |||
You can directly connect a micro SD card to a TWOG. Remember that micro SD cards do have a limited number of insertions and should not be plugged too often. The (micro) SD card is connected to the SPI1 of the TWOG following this scheme: | You can directly connect a micro SD card to a TWOG. Remember that micro SD cards do have a limited number of insertions and should not be plugged too often. The (micro) SD card is connected to the SPI1 of the TWOG following this scheme: | ||
Revision as of 05:37, 19 November 2015
Introduction
This page describes various onboard external devices called a "Data logger", that can be connected to the Paparazzi autopilot.
Such a Data Logger device can be used to store telemetry data to a storage medium on board the aircraft. Such a storage medium can be an SD card or a Flash chip. For now logging is not done directly by the autopilot itself as the usage of a file system as well as possible lag you might get with a SD storage speed does not fit well with the real-time nature of Autopilots.
Note that not all loggers accept SD HighCapacity(SDHC) cards as storage
Why Onboard
One would naturally first ask; why on on-board logger when we have data over the air?
The answer to this is multi-fold; Sometimes it is not possible to log everything over the air because of speed, lag and datavolume limitations of data send wireless over the air. Or one needs to log when there is no telemetry at all in long distance flight. Or one want to log all the RAW IMU data to debug specific scenarios.
To solve this issue, there are various loggers that can be connected to your Paparazzi Autopilot board. A short overview can be found on this page.
Available Data logger options
TWOGA-Logga
An dedicated TWOG board for logging
You can directly connect a micro SD card to a TWOG. Remember that micro SD cards do have a limited number of insertions and should not be plugged too often. The (micro) SD card is connected to the SPI1 of the TWOG following this scheme:
microSD TinyV2 SPI J3 8 nc 7 DO 5 MISO 6 GND 1 GND 5 CLK 7 SCK 4 Vcc 2 +3V3 3 DI 4 MOSI 2 CS 3 SSEL 1 nc
Looking onto the gold plated connector side of the microSD card:
###############
I 8
I 7
I 6
I 5
I 4
I 3
I 2
I 1
###### ##
\ I \
## ##
The start/stop button is connected to the BUTTON (P0.7) pin of the USB connector (J9). It is activated by pulling it low.
Option 3: Logomatic
There is also direct support for the Sparkfun Logomatic V2.6 board,
Software
Just use
conf/airframes/logomatic.xml
Currently autopilot data must be collected on UART0 for sd2log to work [20:40, 9 August 2012 (UTC)]
Option 4: OpenLog
If you don't want to add a complete TWOG or full-blown LPC-Board to you setup you can also use the Sparkfun OpenLog board. Take a look at Openlog.
UART Connection
The two serial inputs LPC_RXD0 (J7) and RXD1 (J2) are used to receive data. The received data is not forwarded to TX0/1 by software (the UART TX pins are deactivated). If the logger is put in between Tiny and the modem the connection should be done with a wire so that a logger failure does not cause any data link issue.
I2C Connection
tbd
SPI Connection
tbd
Configuration
The logger is defined just like an aircraft. Take the
conf/airframes/logger_sd.xml
as example. You can enable one or both UARTs for logging and have to set the serial speed
<configure name="UART0_BAUD" value="B9600" /> <configure name="UART1_BAUD" value="B9600" />
The message type can be switched between the PPRZ and the XBEE format
<configure name="LOG_MSG_FMT" value="LOG_PPRZ"/> or <configure name="LOG_MSG_FMT" value="LOG_XBEE"/>
The SD card can either be connected to SPI0 or SPI1
<configure name="SPI_CHANNEL" value="0" /> or <configure name="SPI_CHANNEL" value="1" />
Now create a new A/C with the logger airframe. Although they will not be used, you still need to supply dummy files for Flight Plan, Settings, Radio and Telemetry.
Decoding
The telemetry is written in the Paparazzi .tlm format that adds a timestamp to each message. The logger starts with 00000000.TLM in the main folder of the SD and increases the number with each log session. Already used numbers will not be overwritten. This data can be converted back to the Paparazzi .log and .data format using sd2log (make sure environment variables are set before running pprz programs from the commandline)
me@home:~/media/usbstick$ ~/paparazzi3/sw/logalizer/sd2log 00000002.TLM Renaming produced file ... 09_08_13__20_55_03_SD.data file produced 09_08_13__20_55_03_SD.log file produced 09_08_13__20_55_03_SD.tlm file saved
It creates timestamps from the .tlm and changes the filename to the take-off time if a GPS message with correct time was available in the file or the current local PC time if no GPS was available. The .log file will be re-created either from the current configuration (if still in existence) or the MD5-labeled files that are stored in var/conf each time you build an aircraft. All resulting files are stored in var/logs with an _SD extension.