Difference between revisions of "Subsystem/imu"
(added info about default calib values for aspirin) |
(added short infor for umarim) |
||
| Line 9: | Line 9: | ||
* ''b2_v1.1'' | * ''b2_v1.1'' | ||
* ''b2_v1.2'' | * ''b2_v1.2'' | ||
* ''[[Umarim_v1.0|umarim]]'' | |||
* ''yai'' | * ''yai'' | ||
* ''crista'' | * ''crista'' | ||
| Line 62: | Line 63: | ||
</source> | </source> | ||
}} | }} | ||
'''Note that for the aspirin IMUs you may leave out the ''GYRO_x'' and ''ACCEL_x'' defines to use the default values from the datasheet.''' | '''Note that for the aspirin and umarim IMUs you may leave out the ''GYRO_x'' and ''ACCEL_x'' defines to use the default values from the datasheet.''' | ||
See the [[ImuCalibration|IMU calibration]] page for the actual calibration instructions. | See the [[ImuCalibration|IMU calibration]] page for the actual calibration instructions. | ||
Revision as of 04:21, 31 May 2012
Currently possible IMU subsystems are
- aspirin_v1.01
- aspirin_v1.51
- aspirin_v2.11
- aspirin_i2c
- aspirin2_i2c
- b2_v1.0
- b2_v1.1
- b2_v1.2
- umarim
- yai
- crista
- crista_hmc5843
- analog
- ppzuav
Notes:
1. Use SPI with DMA, alternatively use i2c version for LPC21xx
Other IMUs can be used through modules or you can just add a subsystem makefile for your own. Also see the IMU calibration page.
| File: conf/airframes/myplane.xml |
<firmware name="fixedwing or rotorcraft">
...
<subsystem name="imu" type="aspirin_v1.5"/>
</firmware>
|
Defining the calibration
In the IMU section the IMU calibration is defined and looks something like this:
| File: conf/airframes/myplane.xml |
<section name="IMU" prefix="IMU_">
<define name="GYRO_P_NEUTRAL" value="32362" />
<define name="GYRO_Q_NEUTRAL" value="32080" />
<define name="GYRO_R_NEUTRAL" value="32096" />
<define name="GYRO_P_SENS" value="1.1032765" integer="16" />
<define name="GYRO_Q_SENS" value="1.1360802599" integer="16" />
<define name="GYRO_R_SENS" value="1.1249874614" integer="16" />
<define name="ACCEL_X_SENS" value="2.45932966" integer="16"/>
<define name="ACCEL_Y_SENS" value="2.45106376" integer="16"/>
<define name="ACCEL_Z_SENS" value="2.47825717" integer="16"/>
<define name="ACCEL_X_NEUTRAL" value="31886"/>
<define name="ACCEL_Y_NEUTRAL" value="32162"/>
<define name="ACCEL_Z_NEUTRAL" value="32941"/>
<define name="MAG_X_SENS" value="3.17378921476" integer="16"/>
<define name="MAG_Y_SENS" value="3.14663275967" integer="16"/>
<define name="MAG_Z_SENS" value="3.26531022727" integer="16"/>
<define name="MAG_X_NEUTRAL" value="2059"/>
<define name="MAG_Y_NEUTRAL" value="1944"/>
<define name="MAG_Z_NEUTRAL" value="2099"/>
</section>
|
Note that for the aspirin and umarim IMUs you may leave out the GYRO_x and ACCEL_x defines to use the default values from the datasheet.
See the IMU calibration page for the actual calibration instructions.
45deg Mag hack
If your magnetometer axes are rotated by 45deg around z. (e.g. with external mag on booz imu v1.0)
| File: conf/airframes/myplane.xml |
<section name="IMU" prefix="IMU_">
...
<define name="MAG_45_HACK" value="1" />
<!--define name="MAG_X_SENS" value="5.14821844457 * sqrt(2)/2" integer="16"/-->
<!--define name="MAG_Y_SENS" value="5.11810156597 * sqrt(2)/2" integer="16"/-->
<define name="MAG_X_SENS" value="3.640340173" integer="16"/>
<define name="MAG_Y_SENS" value="3.619044324" integer="16"/>
<define name="MAG_Z_SENS" value="5.07618333556" integer="16"/>
</section>
|
Defining the orientation of the IMU
Paparazzi has a parameter to define the orientation of the IMU with respect to the body of the vehicle.
Important Not all algorithms properly deal with any BODY_TO_IMU orientation. See the notes for the respective implementation at Subsystem/ahrs and the issue on github. Currently the only way to properly deal with 90deg rotations is to just change the sensors channels (e.g. so that what are normally the x-axis gyros and accels become the y-axis sensors, etc.)
Not defining these values is the same as setting them to zero:
| File: conf/airframes/myplane.xml |
<section name="IMU" prefix="IMU_">
...
<define name="BODY_TO_IMU_PHI" value="0.0" unit="deg"/>
<define name="BODY_TO_IMU_THETA" value="0.0" unit="deg"/>
<define name="BODY_TO_IMU_PSI" value="0.0" unit="deg"/>
</section>
|