Bebop/BLDC

From PaparazziUAV
Jump to navigation Jump to search

General

The BLDC of the Bebop is the Brushless Driver Controller that controls all 4 brushless motors from the Bebop. Motors are 12 permanent magnets. This BLDC contains a closed loop Rotation Per Minute (RPM) controller, and also reads out the battery voltage.

Default LED behavior

  • Green LED blinking: bootloader mode.
  • Green LED fixed: nominal mode.
  • Red LED blinking: critical mode (error code: 10 or 11)
  • Orange LED fixed: minor error detected.

BLDC Protocol

  • 0x02 SET_REF_SPEED
  • 0x20 GET_OBS_DATA
  • 0x40 START_PROP
  • 0x4D TOGGLE_GPIO
  • 0x60 STOP_PROP
  • 0x80 CLEAR_ERROR
  • 0x82 PLAY_SOUND
  • 0xA0 GET_INFO

SET_REF_SPEED (0x02)

Sets the RPM reference of the motors.

Arguments: 10 bytes

  • 0-1: RPM reference Left Front motor (uint16)
  • 2-3: RPM reference Right Front motor (uint16)
  • 4-5: RPM reference Right Back motor (uint16)
  • 6-7: RPM reference Left Back motor (uint16)
  • 8: Reserved (0x00)
  • 9: Checksum (see section bellow)

GET_OBS_DATA (0x20)

Gets the observed data from the motors and battery.

Arguments: 0 byte Receive: 14 bytes

  • 0-1: RPM observed Left Front motor (uint16)*
  • 2-3: RPM observed Right Front motor (uint16)*
  • 4-5: RPM observed Right Back motor (uint16)*
  • 6-7: RPM observed Left Back motor (uint16)*
  • 8-9: Battery voltage in mV (uint16)
  • 10: Status (uint8)
  • 11: Errno (uint8)
  • 12: Temperature in degrees Celcius (uint8)
  • 13: Checksum (see section below)

* Bit 15 is reserved for detecting maximum RPM (depending on voltage and altitude)

Status

  • 0: Init
  • 1: Idle
  • 2: Ramping
  • 3/4: Spinning
  • 5: Stopping
  • 6: Suicided

Errno

  • 0: No error
  • 1: EEPROM corruption
  • 2: Motor stalled
  • 3: Propeller security
  • 4: Communication lost
  • 9: Battery voltage too low
  • 10: Incorrect number of LIPO cells
  • 11: Unplugged motor or broken motor phase or defectuous MOS

START_PROP (0x40)

Starts the propellers. The propellers will not start when the current error is not cleared.

Optional argument:1 byte

  • 0: Motor bitmask (0000ABCD, A:Left Upper, B:Right Upper, C: Right Back, D: Left Back) where 1 is clockwise and 0 is counterclockwise

Receive: 0 byte

TOGGLE_GPIO (0x4D)

Toggle GPIO outputs. The reset will put the BLDC into bootloader mode.

Arguments: 1 byte

  • 0: GPIO bitmask (bit 0: Reset, bit 1: Red LED, bit 2: Green LED)

Receive: 0 bytes

STOP_PROP (0x60)

Stop the propellers when turning.

Arguments: 0 bytes Receive: 0 bytes

CLEAR_ERROR (0x80)

Clear the current error.

Arguments: 0 bytes Receive: 0 bytes

PLAY_SOUND (0x82)

Play a sound. A negative number will loop the sound.

Arguments: 1 byte

  • 0: Sound number (0: None, 1: Short beep, 2: Boot beep, 3: Be-Bop-Ah-Lula, negative: repeat) (int8)

Receive: 0 bytes

GET_INFO (0xA0)

Get information about the BLDC.

Arguments: 0 bytes Receive: 4 bytes or 13 bytes

  • 0: Software version (major)
  • 1: Software version (minor)
  • 2: Software type
  • 3: Number of motors
  • 4-5: Number of flights (uint16)
  • 4-5: Time last flight (uint16)
  • 6-9: Full flight time (uint32)
  • 10: Last error code

Checksum

For all the packets with arguments or where we receive bytes there is a checksum byte at the end. This checksum is a simple XOR algorithm including the first command byte. 

// Credits to Christophe De Wagter for figuring out the Checksum
checksum = CMD_BYTE;
for(int i = 0; i < packet_size; i++)
   checksum = checksum ^ packet[i];

Bootloader Protocol

When the chip is powered on or reseted, the bootloader is started. Green LED is blinking. See the Cypress bootloader protocol documentation AN60317 or use the embedded tool BLDC_Host_Bootloader for flashing a new firmware or leaving the bootloader mode and launching the applicative firmware. Use the PSoC Creator 2.2 (or a more recent version) for creating your own cyacd files. Compile your bootloadable (applicative) project with the hex and elf files of the bootloader project (not given). Use the Miniprog3 for flashing your own bootloader application.

BLDC_Host_Bootloader

Optional arguments: new_firmware.cyacd backup_firmware.cyacd

Default behavior when no arguments are given:

  • new_firmware.cyacd is /lib/firmware/BLDC.cyacd
  • backup_firmware.cyacd is /lib/firmware/.BLDC.cyacd

Behavior: If new_firmware.cyacd is present it will used to be flashed in the microcontroler. Once successfully flashed, the file will be renamed into backup_firmware.cycad. Backup file is used for fixing firmware flash corruption or restoring firmware after a flashling failure with (incorrect firmware, process aborted, etc).

If new_firmware.cyacd is not present: nothing to flash. The bootloader will quit and launch the applicative firmware.

Applicative firmware is launched if and only if no flash corruptions have been found, else the bootloader never leaves.

Reseting the chip

Toggle the \xres io will get the chip reseted and forced it to jump in bootloader mode. 

echo 1 > /sys/class/gpio/gpio199
echo 0 > /sys/class/gpio/gpio199

BLDC Test Bench

This tool is used for testing motors with different kind of velocity reference inputs. Kill the Bebop software before calling it. Use the -h for displaying the help. Cvs file is created in /tmp and can be post processed with Scilab.

Note: due to memory usage limitation in the microcontroler, motor settings and velocity regulator settings cannot be changed or read.

Retrieved from "http://wiki.paparazziuav.org/w/index.php?title=Bebop/BLDC&oldid=19470"