Subsystem/stabilization

Subsystems

Subsystem/actuators

Subsystem/ahrs

Subsystem/gps

Subsystem/imu

Subsystem/ins

Subsystem/stabilization

Subsystem/telemetry

Subsystems

Stabilization subsystem

The stabilization subsystem provides the attitude controller for rotorcrafts.

Currently possible attitude stabilization subsystem types are

• int_quat
• float_quat
• int_euler
• float_euler
• indi

Attitude Control Implementations

There are several different attitude control algorithm implementations.

They use the same STABILIZATION_ATTITUDE xml configuration section:

File: conf/airframes/myplane.xml

<section name="STABILIZATION_ATTITUDE" prefix="STABILIZATION_ATTITUDE_"> <!-- setpoints --> <define name="SP_MAX_PHI" value="45." unit="deg"/> <define name="SP_MAX_THETA" value="45." unit="deg"/> <define name="SP_MAX_R" value="90." unit="deg/s"/> <define name="DEADBAND_A" value="0"/> <define name="DEADBAND_E" value="0"/> <define name="DEADBAND_R" value="250"/> <!-- reference --> <define name="REF_OMEGA_P" value="800" unit="deg/s"/> <define name="REF_ZETA_P" value="0.85"/> <define name="REF_MAX_P" value="400." unit="deg/s"/> <define name="REF_MAX_PDOT" value="RadOfDeg(8000.)"/> <define name="REF_OMEGA_Q" value="800" unit="deg/s"/> <define name="REF_ZETA_Q" value="0.85"/> <define name="REF_MAX_Q" value="400." unit="deg/s"/> <define name="REF_MAX_QDOT" value="RadOfDeg(8000.)"/> <define name="REF_OMEGA_R" value="500" unit="deg/s"/> <define name="REF_ZETA_R" value="0.85"/> <define name="REF_MAX_R" value="180." unit="deg/s"/> <define name="REF_MAX_RDOT" value="RadOfDeg(1800.)"/> <!-- feedback --> <define name="PHI_PGAIN" value="1000"/> <define name="PHI_DGAIN" value="400"/> <define name="PHI_IGAIN" value="200"/> <define name="THETA_PGAIN" value="1000"/> <define name="THETA_DGAIN" value="400"/> <define name="THETA_IGAIN" value="200"/> <define name="PSI_PGAIN" value="500"/> <define name="PSI_DGAIN" value="300"/> <define name="PSI_IGAIN" value="10"/> <!-- feedforward --> <define name="PHI_DDGAIN" value="300"/> <define name="THETA_DDGAIN" value="300"/> <define name="PSI_DDGAIN" value="300"/> </section>

SP_MAX_*

maximum PHI/THETA (roll/pitch) angles and maximum angular velocity R around yaw axis

DEADBAND_*

RC stick deadband around the center for A,E,R (roll,pitch,yaw)

REF_*

parameters for the reference generator

REF_OMEGA_*

second order model natural frequency for respective axis

REF_ZETA_*

second order model damping factor for respective axis

REF_MAX_x

bound on ref model angular speed

REF_MAX_xDOT

bound on ref model angular acceleration

[PHI|THETA|PSI]_[PID]GAIN

gains for the feedback control of the respective axis

[PHI|THETA|PSI]_DDGAIN

feedforward gains for the respective axis

Quaternion

Attitude controllers using quaternions (no gimbal lock). There is a fixed point implementation (recommended) and a floating point implementation for reference and testing.

• fixed point:

  <subsystem name="stabilization" type="int_quat"/>
  

• floating point:

  <subsystem name="stabilization" type="float_quat"/>
  

File: conf/airframes/myplane.xml

<firmware name="rotorcraft"> ... <subsystem name="stabilization" type="int_quat"/> </firmware>

You also need the STABILIZATION_ATTITUDE xml configuration section as described above.

Euler

Attitude controller using Euler Angles. Due to the inherent singularities (e.g. 90deg pitch) of the euler angles representation you can't use this controller if you want to fly in regimes close or at these singularities (e.g. acrobatics or transitioning vehicles). See Control_Loops#Attitude_loop for diagrams of the control loop.

File: conf/airframes/myplane.xml

<firmware name="rotorcraft"> ... <subsystem name="stabilization" type="int_euler"/> </firmware>

You also need the STABILIZATION_ATTITUDE xml configuration section as described above.

INDI

Attitude controller based on an Incremental Nonlinear Dynamic Inversion inner loop. It controls the angular acceleration in an incremental way. Detailed information can be found in the paper 'Adaptive Incremental Nonlinear Dynamic Inversion for Micro Aerial Vehicles' (http://arc.aiaa.org/doi/abs/10.2514/1.G001490).

The idea is that any moment on the drone, results in an angular acceleration. With the onboard gyroscope, we measure the angular rate. This means that if we take the derivative of the angular rate, we have a measure of all moments on the drone through the angular acceleration. This includes the moment caused by the inputs. We know what the angular acceleration is with the inputs that we are giving, so to change the angular acceleration to a desired value, we just need to increment these inputs. How much we should increment the inputs to get a certain increment in angular acceleration is determined by the control effectiveness.

The benefit of using INDI over PID is that the disturbance rejection is a lot faster. This means that an external moment on the drone due to wind or something else is counteracted as fast as the drone can measure it and the actuators can move. Compare this to the integrator gain of a PID controller, that only slowly removes steady state offsets.

More practical information can be found on working with INDI

Rate Control

There is only one rate control implementation. It allows you to fly a rotorcraft like a helicopter by controlling the angular rate directly instead of having (self-leveling) attitude control. See Control_Loops#Rate_loop for diagrams of the control loop.

File: conf/airframes/myplane.xml

<firmware name="rotorcraft"> ... <module name="stabilization" type="rate"/> </firmware> <section name="STABILIZATION_RATE" prefix="STABILIZATION_RATE_"> <!-- setpoints --> <define name="SP_MAX_P" value="10000"/> <define name="SP_MAX_Q" value="10000"/> <define name="SP_MAX_R" value="10000"/> <define name="DEADBAND_P" value="20"/> <define name="DEADBAND_Q" value="20"/> <define name="DEADBAND_R" value="200"/> <define name="REF_TAU" value="4"/> <!-- feedback --> <define name="GAIN_P" value="400"/> <define name="GAIN_Q" value="400"/> <define name="GAIN_R" value="350"/> <define name="IGAIN_P" value="75"/> <define name="IGAIN_Q" value="75"/> <define name="IGAIN_R" value="50"/> <!-- feedforward --> <define name="DDGAIN_P" value="300"/> <define name="DDGAIN_Q" value="300"/> <define name="DDGAIN_R" value="300"/> </section>