Difference between revisions of "Module/Meas Spec MS5611 I2C"
m |
m |
||
| Line 1: | Line 1: | ||
__NOTOC__ | __NOTOC__ | ||
[[Image:Freeimu043.jpg|thumb|right|MS5611-01BA01 as part of the FreeIMU 0.4.3]] | [[Image:Freeimu043.jpg|thumb|right|MS5611-01BA01 as part of the FreeIMU 0.4.3]] | ||
[[Image:Multi_i2c_ms5611.jpg|thumb|right|MS5611-01BA01 as part of the multi adapter board]] | |||
== Overview == | == Overview == | ||
Revision as of 14:30, 13 March 2013
Overview
The Measurement Specialties MS5611 is an excellent barometer/pressure sensor. Currently a plastic case version (-01BA01) and a metal case version (-01BA03) exist. The sensor can be used as I2C or SPI device. This page describes the connection through I2C (the MS5611 mounted on the Aspirin V2.2 uses the SPI port).
The device was tested in a simple static noise comparsion setup.
| Module name | sensors/baro_ms5611_i2c |
| Sensor type | barometer, temperature |
| Range (baro) | 10 kPa .. 1200 kPa |
| Range (temp) | -40°C .. +85°C |
| Resolution (baro) | 1.2 Pa |
| Resolution (temp) | 0.01°C |
| Refresh rate | 4Hz |
| I2C address | 0xEE |
Hardware
The sensor can directly interface to the 3.3V I2C port of the autopilots and is supplied by +3.3V.
Supplier:
Wiring
| Autopilot I2C pin | Autopilot I2C | MS5611 |
| 1 | GND | GND |
| 2 | ||
| 3 | +3.3V | VCC |
| 4 | SDA | SDA |
| 5 | SCL | SCL |
Usage
To use it load the baro_ms5611_i2c module:
| File: conf/airframes/myplane.xml |
<modules>
...
<load name="baro_ms5611_i2c.xml"/>
</modules>
|
Configuration
To see the sensors data in the log file set the SENSOR_SYNC_SEND in your airframe file. Every time new data is available it will be sent directly.
| File: conf/airframes/myplane.xml |
<modules>
...
<load name="baro_ms5611_i2c.xml">
<define name="SENSOR_SYNC_SEND"/>
</load>
</modules>
|
Result message
The raw values (d1/d2) and the corrected ones (pressure/temp) are written to the log file.
| File: conf/messages.xml |
<message name="BARO_MS5611" id="116">
<field name="d1" type="uint32"/>
<field name="d2" type="uint32"/>
<field name="pressure" type="float" unit="hPa" format="%.2f"/>
<field name="temp" type="float" unit="deg_celsius" format="%.2f"/>
</message>
|
The sensors calibration values are read out at init time and transmitted every 30 seconds. They can be seen as some sort of unique serial number.
| File: conf/messages.xml |
<message name="MS5611_COEFF" id="117">
<field name="c0" type="uint16"/>
<field name="c1" type="uint16"/>
<field name="c2" type="uint16"/>
<field name="c3" type="uint16"/>
<field name="c4" type="uint16"/>
<field name="c5" type="uint16"/>
<field name="c6" type="uint16"/>
<field name="c7" type="uint16"/>
</message>
|
Sample log file lines
10.239 123 MS5611_COEFF 8 53136 52817 34048 31158 31184 28953 55558 11.024 123 BARO_MS5611 8049424 8052329 988.8 22.38 11.272 123 BARO_MS5611 8049312 8052284 988.77 22.38 11.524 123 BARO_MS5611 8049344 8052330 988.78 22.39