Umarim v1.0

...UNDER CONSTRUCTION...

Hardware Revision History

Version #	Release Date	Release Notes
v1.0	09/2011	Initial release of Umarim

Features

• 

  Umarim v1.0 3D bottom view

• 

  Umarim v1.0 3D top view

Pinout

Pins Name and Type are specified with respect to the Autopilot Board

SRV0/1/2/3/6/7

Pin #	Name	Type	Description	Suggested Color
1	GND	PWR	common ground	Black
2	+5V	PWR	5V Rail from autopilot	Orange
3	SRVx	OUT	Servo signal (PWM)	White

RC

Pin #	Name	Type	Description	Suggested Color
1	GND	PWR	common ground	Black
2	+5v	PWR	5V Rail from autopilot	Orange
3	PPM_IN	IN	PPM Stream from R/C Receiver (5V tolerant)	White

SPI1

Pin #	Name	Type	Description	Suggested Color
1	GND	PWR	common ground	Black
2	+3.3V	PWR	3.3V Rail from autopilot	Red
3	SSEL1	IN	SSP Slave Select. Selects the SSP interface as a slave (SSEL1)	Brown
4	MOSI1	I/O	SPI1 Master Out Slave In. Data output from master / data input to slave	Grey
5	MISO1	I/O	SPI1 Master In Slave Out. Data input to master / data output from slave	Green
6	DRDY1	IN	External interrupt 0 input (EINT0)	Purple
7	SCK1	I/O	SPI1 Serial clock. Clock output from master or input to slave	Yellow

AUX

Pin #	Name	Type	Description	Suggested Color
1	GND	PWR	common ground	Black
2	+5V	PWR	5V Rail from autopilot	Orange
3	+3.3V	PWR	3.3V Rail from autopilot	Red
4	AUX1	I/O	General Purpose I/O #1 or ADC Input (AD1.5)
5	AUX2	I/O	General Purpose I/O #2 or ADC Input (AD1.4)
6	AUX3	I/O	General Purpose I/O #3 or ADC Input (AD1.3)
7	AUX4	I/O	General Purpose I/O #4 or ADC Input (AD1.2)

UART0

Pin #	Name	Type	Description	Suggested Color
1	GND	PWR	common ground	Black
2	+3.3V	PWR	3.3V Rail from autopilot	Red
3	RXD0	IN	UART0 Serial Input (3.3V level, 5V Tolerant)	Green
4	TXD0	OUT	UART0 Serial Output (3.3V level)	Blue

UART1

Pin #	Name	Type	Description	Suggested Color
1	GND	PWR	common ground	Black
2	+3.3V	PWR	3.3V Rail from autopilot	Red
3	RXD1	IN	UART1 Serial Input (3.3V level, 5V Tolerant)	Green
4	TXD1	OUT	UART1 Serial Output (3.3V level)	Blue

I2C0

Pin #	Name	Type	Description	Suggested Color
1	GND	PWR	common ground	Black
2	+3.3V	PWR	3.3V Rail from autopilot	Red
3	SDA0	I/O (Open Drain)	I2C0 bus Serial DAta	Brown
4	SCL0	I/O (Open Drain)	I2C0 bus Serial CLock	Blue

I2C1

Pin #	Name	Type	Description	Suggested Color
1	GND	PWR	common ground	Black
2	+3.3V	PWR	3.3V Rail from autopilot	Red
3	SDA1 BOOT	I/O (Open Drain)	I2C1 bus Serial DAta In-Circuit Serial Programming (ISP) enable (P0.14, +3.3v pullup) (Note)	Brown
4	SCL1	I/O (Open Drain)	I2C1 bus Serial CLock	Blue

Note: Holding this pin low for at least 3mS after a RESET (or power up) instructs the controller to enter programming mode.

USB

Pin #	Name	Type	Description	Suggested Color
1	GND	PWR	common ground	Black
2	USB+	I/O	USB bidirectional D+ line	Green
3	USB-	I/O	USB bidirectional D- line	White
4	VBUS	IN	Indicates the presence of USB bus power (P0.23) (5V level)	Orange

Assembly

• 

  Umarim v1.0 bottom components Layout

• 

  Umarim v1.0 top components Layout