Difference between revisions of "Subsystem/gps"
Jump to navigation
Jump to search
IHaveADrone (talk | contribs) m (changed code to xml) |
|||
| (2 intermediate revisions by 2 users not shown) | |||
| Line 13: | Line 13: | ||
|- | |- | ||
|''nmea'' || stm32 || all || only basic position and fix information, see [https://github.com/paparazzi/paparazzi/issues/120 #120, fixed] | |''nmea'' || stm32 || all || only basic position and fix information, see [https://github.com/paparazzi/paparazzi/issues/120 #120, fixed] | ||
|- | |||
| ''sirf'' || all || rotorcraft || | |||
|} | |} | ||
Just specify the appropriate subsystem in your firmware section. | Just specify the appropriate subsystem in your firmware section. | ||
{{Box Code|conf/airframes/myplane.xml| | {{Box Code|conf/airframes/myplane.xml| | ||
< | <source lang="xml"> | ||
<firmware name="fixedwing or rotorcraft"> | <firmware name="fixedwing or rotorcraft"> | ||
... | ... | ||
<subsystem name="gps" type="ublox"/> | <subsystem name="gps" type="ublox"/> | ||
</firmware> | </firmware> | ||
</ | </source> | ||
}} | }} | ||
=== Configure Options === | === Configure Options === | ||
If a configure option is not specified the default is used. | If a configure option is not specified the default is used. | ||
* '''GPS_PORT''': ''UART0'', ''UART1'', etc. | * '''GPS_PORT''': ''UART0'', ''UART1'', etc. | ||
** default: The correct UART is already defined according to your board. | ** default: The correct UART is already defined according to your board. | ||
* '''GPS_BAUD''': ''B4800'', ''B9600'', ''B38400'', ''B57600'', ''B115200'' | * '''GPS_BAUD''': ''B4800'', ''B9600'', ''B38400'', ''B57600'', ''B115200'' | ||
** default: ''B38400'' | ** default: Already defined according to your board (e.g. ''B38400'' for Lisa/M v2.0). | ||
* '''GPS_LED''': ''1'', ''2'', ''3'', ''none'' | * '''GPS_LED''': ''1'', ''2'', ''3'', ''none'' | ||
** default: Already defined according to your board (e.g. ''2'' for tiny2 or twog). | ** default: Already defined according to your board (e.g. ''2'' for tiny2 or twog). | ||
Defaults can be found in the board makefile (e.g. conf/boards/ardrone2_raw.makefile). | |||
If you use different baud rates or UART set the according parameters, e.g. | If you use different baud rates or UART set the according parameters, e.g. | ||
{{Box Code|conf/airframes/myplane.xml| | {{Box Code|conf/airframes/myplane.xml| | ||
< | <source lang="xml"> | ||
<firmware name="fixedwing or rotorcraft"> | <firmware name="fixedwing or rotorcraft"> | ||
... | ... | ||
| Line 46: | Line 50: | ||
</subsystem> | </subsystem> | ||
</firmware> | </firmware> | ||
</ | </source> | ||
}} | }} | ||
Latest revision as of 07:08, 19 August 2014
Currently possible GPS subsystems are
| type | architectures | firmwares | notes |
|---|---|---|---|
| ublox | all | all | recommended |
| ublox_utm | all | fixedwing | for the older ublox4 series that still have a UTM message |
| skytraq | all | rotorcraft | some fields missing in the skytraq protocol for fixedwings, see #167, fixed |
| mediatek_diy | all | fixedwing | |
| nmea | stm32 | all | only basic position and fix information, see #120, fixed |
| sirf | all | rotorcraft |
Just specify the appropriate subsystem in your firmware section.
| File: conf/airframes/myplane.xml |
<firmware name="fixedwing or rotorcraft">
...
<subsystem name="gps" type="ublox"/>
</firmware>
|
Configure Options
If a configure option is not specified the default is used.
- GPS_PORT: UART0, UART1, etc.
- default: The correct UART is already defined according to your board.
- GPS_BAUD: B4800, B9600, B38400, B57600, B115200
- default: Already defined according to your board (e.g. B38400 for Lisa/M v2.0).
- GPS_LED: 1, 2, 3, none
- default: Already defined according to your board (e.g. 2 for tiny2 or twog).
Defaults can be found in the board makefile (e.g. conf/boards/ardrone2_raw.makefile).
If you use different baud rates or UART set the according parameters, e.g.
| File: conf/airframes/myplane.xml |
<firmware name="fixedwing or rotorcraft">
...
<subsystem name="gps" type="ublox">
<configure name="GPS_BAUD" value="B9600"/>
<configure name="GPS_PORT" value="UART0"/>
<configure name="GPS_LED" value="none"/>
</subsystem>
</firmware>
|
Notes:
- u-blox GPS modules are factory configured for 9600 baud, 38,400 baud is recommended along with the other required changes. The GPS can be accessed directly thrugh the UART Tunnel and Configured with u-center
- You can also use the GPS u-blox U-Center module to automatically configure baudrate and messages for your u-blox GPS on startup.