Difference between revisions of "Module/Meas Spec MS5611 I2C"
m (→Overview) |
(→Altitude in Autopilot: added baro example code from chris) |
||
| (One intermediate revision by one other user not shown) | |||
| Line 139: | Line 139: | ||
11.272 123 BARO_MS5611 8049312 8052284 988.77 22.38 | 11.272 123 BARO_MS5611 8049312 8052284 988.77 22.38 | ||
11.524 123 BARO_MS5611 8049344 8052330 988.78 22.39 | 11.524 123 BARO_MS5611 8049344 8052330 988.78 22.39 | ||
=Altitude in Autopilot= | |||
If you want to use it for altitude estimation in the autopilot the following line needs to be added to your airframe file: <define name="USE_BARO_MS5611"/> | |||
Other example how to use the baro from [[IMU#Drotek_10DOF_.28MPU6050-HMC5883-MS5611.29|Drotek 10DOF (MPU6050-HMC5883-MS5611)]] | |||
{{Box Code|conf/airframes/myplane.xml| | |||
<source lang="xml"> | |||
<modules> | |||
<!-- baro_ms5611_i2c Alternate address --> | |||
<load name="baro_ms5611_i2c.xml"> | |||
<define name="MS5611_I2C_DEV" value="i2c2" /> | |||
<define name="MS5611_SLAVE_ADDR=0xEE"/> | |||
<define name="MS5611_SEND_BARO_ALTITUDE"/> | |||
<!--<define name="SENSOR_SYNC_SEND"/> --> | |||
</load> | |||
</modules> | |||
</source> | |||
}} | |||
[[Category:User_Documentation]] [[Category:Modules]] | [[Category:User_Documentation]] [[Category:Modules]] | ||
Latest revision as of 10:22, 21 August 2014
Overview
The Measurement Specialties MS5611 is an excellent barometer/pressure sensor. Currently a plastic case version (-01BA01) and a metal case version (-01BA03) exist, both with the same functionallity. The metal case was added since the values form the plastic one change under the influence of bright light. The sensor can be used as I2C or SPI device.
This page describes the connection through I2C. Note that the MS5611 mounted on the Aspirin V2.2 uses the SPI port, the Aspirin V2.1 still I2C
The device was tested in a simple static noise comparsion setup.
| Module name | sensors/baro_ms5611_i2c |
| Sensor type | barometer, temperature |
| Range (baro) | 10 kPa .. 1200 kPa |
| Range (temp) | -40°C .. +85°C |
| Resolution (baro) | 1.2 Pa |
| Resolution (temp) | 0.01°C |
| Refresh rate | 4Hz |
| I2C address | 0xEE |
Hardware
The sensor can directly interface to the 3.3V I2C port of the autopilots and is supplied by +3.3V.
Supplier:
Wiring
| Autopilot I2C pin | Autopilot I2C | MS5611 |
| 1 | GND | GND |
| 2 | ||
| 3 | +3.3V | VCC |
| 4 | SDA | SDA |
| 5 | SCL | SCL |
Usage
To use it load the baro_ms5611_i2c module:
| File: conf/airframes/myplane.xml |
<modules>
...
<load name="baro_ms5611_i2c.xml"/>
</modules>
|
Configuration
To see the sensors data in the log file set the SENSOR_SYNC_SEND in your airframe file. Every time new data is available it will be sent directly.
| File: conf/airframes/myplane.xml |
<modules>
...
<load name="baro_ms5611_i2c.xml">
<define name="SENSOR_SYNC_SEND"/>
</load>
</modules>
|
Result message
The raw values (d1/d2) and the corrected ones (pressure/temp) are written to the log file.
| File: conf/messages.xml |
<message name="BARO_MS5611" id="116">
<field name="d1" type="uint32"/>
<field name="d2" type="uint32"/>
<field name="pressure" type="float" unit="hPa" format="%.2f"/>
<field name="temp" type="float" unit="deg_celsius" format="%.2f"/>
</message>
|
The sensors calibration values are read out at init time and transmitted every 30 seconds. They can be seen as some sort of unique serial number.
| File: conf/messages.xml |
<message name="MS5611_COEFF" id="117">
<field name="c0" type="uint16"/>
<field name="c1" type="uint16"/>
<field name="c2" type="uint16"/>
<field name="c3" type="uint16"/>
<field name="c4" type="uint16"/>
<field name="c5" type="uint16"/>
<field name="c6" type="uint16"/>
<field name="c7" type="uint16"/>
</message>
|
Sample log file lines
10.239 123 MS5611_COEFF 8 53136 52817 34048 31158 31184 28953 55558 11.024 123 BARO_MS5611 8049424 8052329 988.8 22.38 11.272 123 BARO_MS5611 8049312 8052284 988.77 22.38 11.524 123 BARO_MS5611 8049344 8052330 988.78 22.39
Altitude in Autopilot
If you want to use it for altitude estimation in the autopilot the following line needs to be added to your airframe file: <define name="USE_BARO_MS5611"/>
Other example how to use the baro from Drotek 10DOF (MPU6050-HMC5883-MS5611)
| File: conf/airframes/myplane.xml |
<modules>
<!-- baro_ms5611_i2c Alternate address -->
<load name="baro_ms5611_i2c.xml">
<define name="MS5611_I2C_DEV" value="i2c2" />
<define name="MS5611_SLAVE_ADDR=0xEE"/>
<define name="MS5611_SEND_BARO_ALTITUDE"/>
<!--<define name="SENSOR_SYNC_SEND"/> -->
</load>
</modules>
|