Difference between revisions of "Debug Probes"
(→FT2232H Mini Module: added jtag pinout) |
m (added lyorak probe pinout graphic) |
||
| Line 13: | Line 13: | ||
==Lyorak Probe== | ==Lyorak Probe== | ||
[[Image:Lyorak_front.jpg|300px| | [[Image:Lyorak_front.jpg|300px|Lyorak probe]] | ||
[[Image:Lyorak_pinout.jpeg|500px|Lyorak probe pinout]] | |||
The Lyorak probe is a programming and debugging tool for ARM Cortex MCU, based on [http://www.blacksphere.co.nz/main/blackmagic Black Magic Probe]. <br/> | The Lyorak probe is a programming and debugging tool for ARM Cortex MCU, based on [http://www.blacksphere.co.nz/main/blackmagic Black Magic Probe]. <br/> | ||
Revision as of 02:07, 21 June 2014
These various programming adapters and probes can be used for flashing, debugging and some as serial adapters.
CricketProbe v1.00
The CricketProbe is a programming and debugging tool for ARM Cortex MCU, based on Black Sphere Technologies Black Magic Probe.
Lyorak Probe
The Lyorak probe is a programming and debugging tool for ARM Cortex MCU, based on Black Magic Probe.
Designed with 1206 SMD components for easy assmbly and a CAN interface.
Documentation
molnarkares/blackmagic git repo
Black Magic Probe
This is the original Black Magic Probe from Black Sphere Technologies, a programming and debugging tool for ARM Cortex MCU.
Documentation
gsmcmullin/blackmagic git repo
FLOSS JTAG
The FLOSS JTAG is based on an FTDI 2232HL chip that allows two simultaneous USB connections, which means that FLOSS JTAG allows JTAG and UART/COM connections.
The FT2232H Mini Module can also be used since this has the same chip.
On the bottom side there is 4 pin UART/COM connector, which contains (from top to bottom on the image, or color dots): Ground (black), RX (orange), TX (yellow), and +5V (red)
Documentation
randomprojects.org/wiki/Floss-JTAG
FT2232H Mini Module
The FT2232H Mini modules can be used with blackmagic firmware or as FLOSS-JTAG device.
More Information can be found at the FT2232H Mini Module Serial Adapter page.
Important
Out of the box, there is NO power supply for the FT2232H because this can either done with USB or external 5V.
The pictures above show two different PCB versions. The suggested connections only apply to the right (latest) layout.
Connect: (for power supply over USB)
- CN3 pin 1 to CN3 pin 3
- CN2 pin group 1,3,5 to CN2 pin group 11,21 and to CN3 pin group 12,22
Pinout
| Use | Pin | Name |
|---|---|---|
| UART1 RX | CN2-10 | ADBUS1 |
| UART1 TX | CN2-7 | ADBUS0 |
| UART2 RX | CN3-25 | BDBUS1 |
| UART2 TX | CN3-26 | BDBUS0 |
| Use | Pin | Name |
|---|---|---|
| JTAG1 TCK | CN2-7 | ADBUS0 |
| JTAG1 TDI | CN2-10 | ADBUS1 |
| JTAG1 TDO | CN2-9 | ADBUS2 |
| JTAG1 TMS | CN2-12 | ADBUS3 |
| JTAG2 TCK | CN3-26 | BDBUS0 |
| JTAG2 TDI | CN3-25 | BDBUS1 |
| JTAG2 TDO | CN3-24 | BDBUS2 |
| JTAG2 TMS | CN3-23 | BDBUS3 |
Blackmagic firmware
First, get the VID/PID for your FT2232 device using 'lsusb'. Edit the file 'src/libftdi/platform.h' and change the VID/PID to match your hardware. Compile the application with the command:
make PROBE_HOST=libftdi
FLOSS-JTAG
With the tool "FT_Prog" change the description the FT2232H to "FLOSS-JTAG".
Documentation
FT2232H Datasheet
FT2232H Mini Module Datatsheet
Mouser shop 22€