Trashcan

About

A racing drone with quite a long name for a tiny flying machine; Eachine TRASHCAN 75mm Crazybee F4 PRO OSD 2S Whoop FPV Racing Drone Caddx Eos2 Adjustable Camera 25~200mW VTX Swtichable

Supplier:

• https://www.banggood.com/Eachine-TRASHCAN-75mm-Crazybee-F4-PRO-OSD-2S-Whoop-FPV-Racing-Drone-Caddx-Eos2-Adjustable-Camera-p-1386071.html

Specifications:

Base

• Brand Name: Eachine
• Model Name: TRASHCAN
• Item Name: 2S 75mm Brushless Whoop racer drone BNF/PNP
• Wheelbase: 75mm
• Size: 98mm*98mm*36mm
• Weight: 33g(without battery)
• Weight:48g(with Original 1s 300mah lipo battery x2)

Spare parts specifications:

• Motor Mode: TC0803 KV15000
• Configuration: 9N12P
• Stator Diamter: 8mm
• Stator Length: 3mm
• Shaft Diameter: Φ1mm
• Motor Dimension(Dia.*Len): Φ10.5mm*14.5mm
• Weight(g): 2.2g
• No.of Cells(Lipo): 1S-2S

Flight controller

• CRAZYBEE F4 PRO FR Firmware target: CrazybeeF4FR

VTX

• Output power: 25~200mw switchable
• Frequency: 40CH
• Input voltage: 3.3V 5.5V
• Current consumption: 300mA(type)
• Antenna: RG178 antenna
• Frequency: 5.8GHz 5bands 40 channels
• With Raceband
• Smart Audio ready
• Weight: 3g

Camera

• CADDX EOS2 camera
• 1/3" CMOS Sensor
• 1200 TVL
• 2.1mm lens
• 16:9 Image size
• NTSC
• Global WDR
• Internal Synchronization

Battery

• Capacity: 300mAh
• Type: LiPo HV
• Voltage: 3.8v
• Continuous Discharge Rate: 40C
• Instantaneous discharge rate: 80C
• Size: 55mmx11.5mmx6.5mm
• Weight: 7.8g
• Connector: PH2.0

Notes: Need 2pcs batteries for Series circuit

Alternative Battery

https://www.banggood.com/5Pcs-Gaoneng-3_8V-550mAh-50C100C-Lipo-Battery-PH2_0-Plug-For-Tiny-RC-Helicopter-Drone-p-1348860.html

• Type: Gaoneng 3.8v 550mAh 50C/100C 1S Lipo Battery
• Capacity: 550mAh
• Type: LiPo HV
• Voltage: 3.8v
• Continuous Discharge Rate: 50C
• Instantaneous discharge rate: 100C
• Size: 7*17*65m
• Weight: 14g
• Connector: Molex Picoblade PH2.0

Features:

• PNP version support TBS receiver
• Crazybee F4 PRO Flight controller 1-2s Lipo Compatible
• 2S whoop more powerful and more flight time
• Betaflight support , multi flight mode: ACRO/AIR/ANGLE
• New 0803 Powerful and High efficiency Brushless motor and Smooth ESC. The motor power with 7V and 40mm propeller can get 55g pull. It is more powerful pull than 0802 49g.
• Betaflight OSD support ,easy to get RSSI, Voltage ,current from your goggles(DSMX version no RSSI output)
• Caddx EOS2 camera ready , More comfortable FPV experience
• Camera Angle adjustable (0-35°)
• VTX power switchable 25mw~200mw
• Smart Audio ready , change VTX bands, powers, channels via OSD
• Adjust the settings and the PID of the flight controller via OSD
• Frsky Non-EU version support NON-EU Frsky transmitter D8/D16 compatible
• Flysky version support both AFHDS and AFHDS-2A protocol transmitter
• DSM2/DSMX version support DSM2 and DSMX compatible Spektrum transmitter
• No RX version support external serial-bus receiver like xm+, crossfire, S-FHSS etc..
• Full telemetry function ready (Frsky Non-EU and Flysky version support)
• Support buzzer
• LED_Strip Ready
• Real Bind and Fly version
• Compatible both for 1s-2s

Package

For example the BNF FrSky Version

• 1 x 75mm Brushless whoop Frame
• 1 x Crazybee F4 PRO FC built-in Frsky NON-EU receiver
• 4 x TC0803 KV15000 Motor
• 1 x 40mm propeller(4cw+4ccw)
• 1 x Caddx EOS2 camera
• 1 x 5.8G 40ch 25mw~200mw VTX
• 4 x 3.8v 300mah 40C/80C battery
• 1 x USB Lipo/LIHV Charger
• 1 x Propeller disassemble tool
• 1 x LED board
• 1 x Screwdriver
• 1 x XT30 wire
• 1 x Bag

External RC Receiver

For example an open R-XSR receiver set to PPM out and connected on the LED port of the flightcontroller board, no (mis) used for PPm input signals instead of LED board output.

{Here photo where to solder it}

GNSS

A Position sensor not (yet) added, could be a SAM M8Q or

Telemetry

A small ESP8266 based WiFi module is added.

Airframe file

Multiple targets in one airframe file: AP, FPV race, ACRO

openuas_eachine_trashcan.xml  (Coming soon to PPRZ master)

Modification

The LED strip is removed and this pin makes room for a RC receiver. Reason to have a separate MCU for RC and not bog down the mail AP loop with build in SPI receiver messages.

Wifi

Solder T2 and R2 to the The GNDF and the VCC come from here

Power conversion

• Ultra-Small Size DC-DC Step Down Power Supply Module 3A Buck Converter Adjustable 1.8V 2.5V 3.3V 5V 9V 12V
• https://www.aliexpress.com/item/32880983608.html

Flashing

USB cable

Uploading Paparazzi airborne autopilot software, also known a flashing is simple. New onboard software for the board can uploaded by connecting your PC via a micro-USB port to the autopilot board. For this the board needs to contain a bootloader. AFAWK all Trashcans come with a Betaflight already flashed on the board.

An alternative to get your firmware in the board is by using a Black Magic Probe JTAG/SWD debugger and programmer connected via the DWD pin. Not all to easy..

Serial Firmware Upload

Firmware upload using the factory integrated bootloader can be useful e.g. if you have overwritten the bootloader accidentally and don´t have access to JTAG. Either set the flash mode in the target section of the airframe configuration:

   <configure name="FLASH_MODE" value="SERIAL"/>

or add it to the commandline invocation:

make AIRCRAFT=<aircraftname> ap.upload FLASH_MODE=SERIAL