Difference between revisions of "Dev/Caspa"
Jump to navigation
Jump to search
| Line 22: | Line 22: | ||
=== Step-by-step === | === Step-by-step === | ||
===== Create a bootable MicroSD card if you do not have one ===== | |||
[http://code.google.com/p/beagleboard/wiki/LinuxBootDiskFormat Follow this] and use LABEL1 as 'mmcblk0p1' and LABEL2 as 'mmcblk0p2'. | [http://code.google.com/p/beagleboard/wiki/LinuxBootDiskFormat Follow this] and use LABEL1 as 'mmcblk0p1' and LABEL2 as 'mmcblk0p2'. | ||
===== Load a pre-built standard image ===== | |||
wget http://cumulus.gumstix.org/images/angstrom/factory/2011-03-25-1619/omap3-desktop-nand-image-overo-booted.tar.bz2 | wget http://cumulus.gumstix.org/images/angstrom/factory/2011-03-25-1619/omap3-desktop-nand-image-overo-booted.tar.bz2 | ||
| Line 37: | Line 37: | ||
cp uImage /media/mmcblk0p1 | cp uImage /media/mmcblk0p1 | ||
===== Replace some files to get the camera modules working ===== | |||
wget http://cumulus.gumstix.org/images/angstrom/misc/caspapx/uImage-2.6.34 | wget http://cumulus.gumstix.org/images/angstrom/misc/caspapx/uImage-2.6.34 | ||
| Line 45: | Line 45: | ||
cp uImage-2.6.34 /media/mmcblk0p2/boot/uImage | cp uImage-2.6.34 /media/mmcblk0p2/boot/uImage | ||
===== Attach the camera to the Overo board ===== | |||
Insert the white ribbon cable contact-side-up into the Caspa connector and contact side down into the Overo connector. | Insert the white ribbon cable contact-side-up into the Caspa connector and contact side down into the Overo connector. | ||
===== Insert MicroSD card in the Overo board ===== | |||
===== Set environment variables ===== | |||
* Connect the expansion board to the host machine via USB B (Console) | |||
* On the host machine do: | |||
[sudo apt-get install ckermit] | [sudo apt-get install ckermit] | ||
kermit -l /dev/ttyUSB0 | kermit -l /dev/ttyUSB0 | ||
| Line 68: | Line 68: | ||
You have now a console connection to the Overo | You have now a console connection to the Overo | ||
* Power-up the expansion board | |||
* Hit 'Enter' to interrupt the boot sequence | |||
* Type in the console: | |||
nand erase 240000 20000 | nand erase 240000 20000 | ||
reset | reset | ||
| Line 78: | Line 76: | ||
This makes the Overo to read the environment variables defined by the kernel in the MicroSD. You just have to this once after setting up the card. | This makes the Overo to read the environment variables defined by the kernel in the MicroSD. You just have to this once after setting up the card. | ||
* Hit 'Enter' to interrupt the boot sequence again | |||
* Type in the console: | |||
setenv defaultdisplay lcd43; saveenv; | setenv defaultdisplay lcd43; saveenv; | ||
reset | reset | ||
| Line 86: | Line 83: | ||
You just have to this once after setting up the card. | You just have to this once after setting up the card. | ||
===== Get the image ===== | |||
* Let the Overo boot properly | |||
* Touch the screen and calibrate it as indicated. You just have to this once after setting up the card. | |||
* Type in the console: | |||
overo login: root | overo login: root | ||
export DISPLAY=:0.0 | export DISPLAY=:0.0 | ||
Revision as of 05:45, 6 July 2011
This page describes the ongoing work to fully integrate a Caspa FS camera on a Lisa/L board. Any advices/suggestions/contributions are welcome.
Final Goal
The final goal is to have a Caspa FS camera connected to the Overo chip on a Lisa/L board. The Overo chip should be able to communicate with the STM32 via SPI. The link shall be used to transmit the result of the image processing computed by the Overo. However this should be flexible enough to let some room for the developer to decide which processing to do and which kind of data to send.
Methods
The following lists the steps that are deemed to be important in achieving the final goal.
- Bitbake a kernel for Overo that includes the camera modules and the SPI modules
- Bitbake a kernel for STM32 that includes the SPI modules
Caspa camera on an Overo expansion board
As a first step a simple connection between the camera and the Overo was tried using an Overo expansion board, i.e. not the the Lisa/L board.
Hardware components
Step-by-step
Create a bootable MicroSD card if you do not have one
Follow this and use LABEL1 as 'mmcblk0p1' and LABEL2 as 'mmcblk0p2'.
Load a pre-built standard image
wget http://cumulus.gumstix.org/images/angstrom/factory/2011-03-25-1619/omap3-desktop-nand-image-overo-booted.tar.bz2 tar -xf omap3-desktop-nand-image-overo-booted.tar.bz2 -C /media/mmcblk0p2 wget http://cumulus.gumstix.org/images/angstrom/factory/2011-03-25-1619/MLO wget http://cumulus.gumstix.org/images/angstrom/factory/2011-03-25-1619/u-boot.bin wget http://cumulus.gumstix.org/images/angstrom/factory/2011-03-25-1619/uImage cp MLO /media/mmcblk0p1 cp u-boot.bin /media/mmcblk0p1 cp uImage /media/mmcblk0p1
Replace some files to get the camera modules working
wget http://cumulus.gumstix.org/images/angstrom/misc/caspapx/uImage-2.6.34 wget http://cumulus.gumstix.org/images/angstrom/misc/caspapx/modules-2.6.34.tgz tar -xf modules-2.6.34.tgz -C /media/mmcblk0p2/ cp uImage-2.6.34 /media/mmcblk0p1/uImage cp uImage-2.6.34 /media/mmcblk0p2/boot/uImage
Attach the camera to the Overo board
Insert the white ribbon cable contact-side-up into the Caspa connector and contact side down into the Overo connector.
Insert MicroSD card in the Overo board
Set environment variables
- Connect the expansion board to the host machine via USB B (Console)
- On the host machine do:
[sudo apt-get install ckermit] kermit -l /dev/ttyUSB0 C-Kermit>set flow-control none C-Kermit>set carrier-watch off C-Kermit>set speed 115200 /dev/ttyUSB0, 115200 bps C-Kermit>connect Connecting to /dev/ttyUSB0, speed 115200 Escape character: Ctrl-\ (ASCII 28, FS): enabled Type the escape character followed by C to get back, or followed by ? to see other options.
You have now a console connection to the Overo
- Power-up the expansion board
- Hit 'Enter' to interrupt the boot sequence
- Type in the console:
nand erase 240000 20000 reset
This makes the Overo to read the environment variables defined by the kernel in the MicroSD. You just have to this once after setting up the card.
- Hit 'Enter' to interrupt the boot sequence again
- Type in the console:
setenv defaultdisplay lcd43; saveenv; reset
You just have to this once after setting up the card.
Get the image
- Let the Overo boot properly
- Touch the screen and calibrate it as indicated. You just have to this once after setting up the card.
- Type in the console:
overo login: root export DISPLAY=:0.0 mplayer tv:// -tv driver=v4l2:device=/dev/video0 -x 480 -y 272 -vo x11
The camera image should appear on the LCD display.
Based on: Gumstix wiki.