Difference between revisions of "Dev/Caspa"
| Line 1: | Line 1: | ||
This page describes the ongoing work to fully integrate a [http://www.gumstix.com/store/product_info.php?products_id=254 Caspa FS camera] on a [[Lisa]]/L board. Any advices/suggestions/contributions are welcome. | This page describes the ongoing work to fully integrate a [http://www.gumstix.com/store/product_info.php?products_id=254 Caspa FS camera] on a [[Lisa]]/L board. Any advices/suggestions/contributions are welcome. | ||
= Final Goal = | == Final Goal == | ||
The final goal is to have a [http://www.gumstix.com/store/product_info.php?products_id=254 Caspa FS camera] connected to the Overo chip on a [[Lisa]]/L board. The Overo chip should be able to communicate with the STM32 via SPI. The link shall be used to transmit the result of the image processing computed by the Overo. However this should be flexible enough to let some room for the developer to decide which processing to do and which kind of data to send. | The final goal is to have a [http://www.gumstix.com/store/product_info.php?products_id=254 Caspa FS camera] connected to the Overo chip on a [[Lisa]]/L board. The Overo chip should be able to communicate with the STM32 via SPI. The link shall be used to transmit the result of the image processing computed by the Overo. However this should be flexible enough to let some room for the developer to decide which processing to do and which kind of data to send. | ||
= Methods = | == Methods == | ||
The following lists the steps that are deemed to be important in achieving the final goal. | The following lists the steps that are deemed to be important in achieving the final goal. | ||
| Line 10: | Line 10: | ||
# Bitbake a kernel for STM32 that includes the SPI modules | # Bitbake a kernel for STM32 that includes the SPI modules | ||
= Caspa camera on an Overo expansion board = | == Caspa camera on an Overo expansion board == | ||
As a first step a simple connection between the camera and the Overo was tried using an Overo expansion board, i.e. not the the [[Lisa]]/L board. | As a first step a simple connection between the camera and the Overo was tried using an Overo expansion board, i.e. not the the [[Lisa]]/L board. | ||
== Hardware components == | === Hardware components === | ||
* [http://www.gumstix.com/store/product_info.php?products_id=254 Caspa FS camera] | * [http://www.gumstix.com/store/product_info.php?products_id=254 Caspa FS camera] | ||
* [http://www.gumstix.com/store/product_info.php?products_id=258 CLB047 cable] | * [http://www.gumstix.com/store/product_info.php?products_id=258 CLB047 cable] | ||
| Line 20: | Line 20: | ||
* [http://www.gumstix.com/store/product_info.php?products_id=244 LCD Touch Screen] | * [http://www.gumstix.com/store/product_info.php?products_id=244 LCD Touch Screen] | ||
=== Step-by-step === | |||
===== Create a bootable MicroSD card if you do not have one ===== | |||
http://code.google.com/p/beagleboard/wiki/LinuxBootDiskFormat | [http://code.google.com/p/beagleboard/wiki/LinuxBootDiskFormat | Follow this] (use LABEL1 as mmcblk0p1 and LABEL2 as mmcblk0p2) | ||
(use LABEL1 as mmcblk0p1 and LABEL2 as mmcblk0p2) | |||
# Load it with a pre-built standard image | |||
Go to http://cumulus.gumstix.org/images/angstrom/factory/2011-03-25-1619/ | Go to http://cumulus.gumstix.org/images/angstrom/factory/2011-03-25-1619/ | ||
Revision as of 05:06, 6 July 2011
This page describes the ongoing work to fully integrate a Caspa FS camera on a Lisa/L board. Any advices/suggestions/contributions are welcome.
Final Goal
The final goal is to have a Caspa FS camera connected to the Overo chip on a Lisa/L board. The Overo chip should be able to communicate with the STM32 via SPI. The link shall be used to transmit the result of the image processing computed by the Overo. However this should be flexible enough to let some room for the developer to decide which processing to do and which kind of data to send.
Methods
The following lists the steps that are deemed to be important in achieving the final goal.
- Bitbake a kernel for Overo that includes the camera modules and the SPI modules
- Bitbake a kernel for STM32 that includes the SPI modules
Caspa camera on an Overo expansion board
As a first step a simple connection between the camera and the Overo was tried using an Overo expansion board, i.e. not the the Lisa/L board.
Hardware components
Step-by-step
Create a bootable MicroSD card if you do not have one
| Follow this (use LABEL1 as mmcblk0p1 and LABEL2 as mmcblk0p2)
- Load it with a pre-built standard image
Go to http://cumulus.gumstix.org/images/angstrom/factory/2011-03-25-1619/ Untar the content of 'omap3-desktop-nand-image-overo-booted.tar.bz2' to the partion mmcblk0p2 Put the files 'MLO', 'u-boot.bin', 'uImage' into the partition mmcblk0p1
3. Replace some files to get the camera modules working
Download: http://cumulus.gumstix.org/images/angstrom/misc/caspapx/uImage-2.6.34 http://cumulus.gumstix.org/images/angstrom/misc/caspapx/modules-2.6.34.tgz
Do: $ tar -xf modules-2.6.34.tgz -C /media/mmcblk0p2/ $ cp uImage-2.6.34 /media/mmcblk0p1/uImage $ cp uImage-2.6.34 /media/mmcblk0p2/boot/uImage
4. Attach the camera to the Overo board
Insert the white ribbon cable contact-side-up into the Caspa connector and contact side down into the Overo connector.
5. Insert MicroSD card in the Overo board
6. Set environment variables
Connect the expansion board to the host machine via USB
On the host machine do: sudo apt-get install ckermit $ kermit -l /dev/ttyUSB0 C-Kermit>set flow-control none C-Kermit>set carrier-watch off C-Kermit>set speed 115200 /dev/ttyUSB0, 115200 bps C-Kermit>connect Connecting to /dev/ttyUSB0, speed 115200 Escape character: Ctrl-\ (ASCII 28, FS): enabled Type the escape character followed by C to get back, or followed by ? to see other options.
Power-up the expansion board
Hit 'Enter' to interrupt the boot sequence Type: nand erase 240000 20000 reset Hit 'Enter' to interrupt the boot sequence Type: setenv defaultdisplay lcd43; saveenv; reset
7. Get the image
Let the Overo boot properly Touch the screen and calibrate it as indicated In the serial command line do: overo login: root export DISPLAY=:0.0 mplayer tv:// -tv driver=v4l2:device=/dev/video0 -x 480 -y 272 -vo x11
The camera image should appear in the LCD display
Based on: http://wiki.gumstix.org/index.php?title=Caspa_camera_boards