Booz

Overview

Booz is an extension of Paparazzi to VTOLs. At the current stage of the project, the system provides attitude stabilization, vertical guidance and automatic navigation. It is able to use simple Paparazzi flight plans ( only go instructions ) and uses Paparazzi telemetry and datalink, which means all the Paparazzi ground segment applications are available( plotter, settings, gcs, etc...)

The current autopilot consist in 3 boards

• The main board, comprising power supply, a LPC2148 and a barometer.
• The IMU board, comprising gyroscopes, accelerometers, magnetometers and a 16 bits ADC.
• The GPS board, using a LEA-5H by ublox.

It flies on a variety of Quad-rotor platforms

and less common vehicles

Program Sources

Everything is at savannah.

-hardware in paparazzi4/trunk/hw/booz
-code in paparazzi3/trunk

Hardware

Purchasing Hardware

There are now vendors offering Booz hardware, Please see the Get Hardware page for details.

Building Tips

Since the Booz uses the same LPC2148 as the Tiny and TWOG autopilots and runs the same core code the documented steps are nearly the same for booz. Below more Booz specific tests are given. However after assembly you load the bootloader in the same way to enable programming via the USB interface.

Assembly Tips

• BOM
• Assembly Notes
• Expected voltages for newly created boards

Loading the USB Boot Loader

Create a cable that has Tx/Rx and Ground along with the ability to hold P0.14 low (i.e. grounded). My cable has P0.14 pin connected to ground as I have found P0.14 should be held low during the entire upload process. See the Eagle Schematic for the pinouts on the GPS connector you will use to upload (same connector as the Tiny/TWOG). NOTE: You can not use the same cable as the Tiny/TWOG.

Running a simulator

Quick start guide

Booz contains a sensors model and can use Jsbsim to allow arbitrarily complex flight dynamic models.

• Extract a copy of paparazzi3 svn

 svn co svn://svn.savannah.nongnu.org/paparazzi/paparazzi3/trunk paparazzi3

• Install all required dependancies

apt-get install paparazzi-dev libtool

• Compile JSBSIM

 cvs -z3 -d:pserver:anonymous@jsbsim.cvs.sourceforge.net:/cvsroot/jsbsim co -P JSBSim 
 cd JSBSim
 ./autogen.sh
 ./configure --enable-maintainer-mode --enable-compile-warnings --enable-libraries --enable-shared --prefix=/opt/jsbsim
 make
 sudo make install

Here is a patch to silent warnings. Also be sure automake and autoconf are installed. If not sudo apt-get install automake autoconf

• Compile paparazzi

 cd paparazzi3/trunk
 make

• Compile the vehicle

 make AIRCRAFT=BOOZ2_A1 clean_ac sim

• Start paparazzi_center if you want click to start programs

./paparazzi

• Start messages to monitor the middleware activity ( from the tool menu of paparazzi center) or with

./sw/ground_segment/tmtc/messages 

• Start the sim

LD_LIBRARY_PATH=/opt/jsbsim/lib ./var/BOOZ2_A1/sim/simsitl

You should now see activity in the "messages" window

• Plot the value of a message field.

start 'plotter' ( from the tool menu of paparazzi center) or with

 ./sw/logalizer/plotter

for example drag the label 'int32 phi' from the BOOZ2_FP message to the drawing area of the plotter

• Use the datalink to change the temetry mode

start 'settings' ( from the tool menu of paparazzi center) or with

 ./sw/ground_segment/tmtc/settings -ac BOOZ2_A1

start 'server' to dispatch datalink messages ( from the tool menu of paparazzi center) or with

./sw/ground_segment/tmtc/server 

change the field "telemetry" on the first page to "Att loop" and send by pressing the green check button. THe label on the left or the drop box should change to "Att loop" confirming your essage has been received. "message" should now show that the message "BOOZ2_STAB_ATTITUDE" is received

• Use flightgear to visualize your vehicle

If you want a view of a quadrotor in flightgear, make a link from

/usr/share/games/FlightGear/Models/Aircraft/paparazzi to PAPARAZZI_SRC/conf/simulator/flightgear/

start flighgear with

fgfs --fdm=null --native-gui=socket,in,30,,5501,udp --prop:/sim/model/path=Models/Aircraft/paparazzi/mikrokopter.xml

restart your simulator with

 LD_LIBRARY_PATH=/opt/jsbsim/lib ./var/BOOZ2_A1/sim/simsitl --fg_host 127.0.0.1

• Save you session

Tunning the attitude control loop

Here we are going to use the simulator to demonstrate a way of tunning the attitude control loop.

• Restart your previous session

• Set telemetry mode to "Att loop"

• Display two real time plotter windows

In the first one, plot the field "m_phi" from the "BOOZ2_STAB_ATTITUDE" message. This is our estimation of roll angle. On top of that, plot the field "phi" from the "BOOZ2_STAB_ATTITUDE_REFERENCE" message. This is our reference roll angle, that is, the roll value we are trying to achieve.

In the second plotter, plot the fields "delta_a_fb" and "delta_a_ff". Those are respectively the feddback and feedforward part of our roll command. The sum of those two terms is what is used as roll command.The feedforward part is the part used to follow our trajectory and the feedback part is the part used to reject perturbations.

• In "Settings", go to the "Att Loop" tab

We notice that the vehicle doesn't follow accurately the step trajectory we are trying to make him do.

Start by setting the value of the proportional gain ('pgain_phi') to 1000 instead of 400. The vehicle now follows the trajectory faster but overshoots. To prevent that, increase the value of the derivative gain ('dgain p') from -300 to -700.

If you look at the plotter where you're ploting the commands, you'll notice that during steps, the feedback command has to work hard. This means that our feedforward command is badly tunned, and namely not working hard enough.Increase the value of the feedforward gain ('ddgain p') from 300 to 540. You'll notice that now the feedback command has becomed marginal during the steps. This is the right value for the gain. Anything bigger will make the feedback command fight against the feedforward command during steps, anything smaller will make the feedback command have to complement the feedforward command.

Something else

• try starting flightgear with

fgfs --fdm=null --native-gui=socket,in,30,,5501,udp --prop:/sim/model/path=Models/Aircraft/paparazzi/simple_bipe.xml

an the sim with

LD_LIBRARY_PATH=/opt/jsbsim/lib ./var/BOOZ2_A1/sim/simsitl --fg_host 127.0.0.1 --rc_script 1

Hardware Test

Booz comes with a number of simple test programs that you can use to validate a newly assembled board or learn how booz code works in case you want to extend it. The Makefile for those is in conf/autopilot/booz2_test_progs.makefile

test_downlink

Paparazzi's Makefile allow you to build different TARGETS (aka programs) using a doted notation. The begining of the Makefile reads

 #
 # test downlink
 #
 test_downlink.ARCHDIR = $(ARCHI)
 test_downlink.ARCH = arm7tdmi
 test_downlink.TARGET = test_downlink
 test_downlink.TARGETDIR = test_downlink
 #
 test_downlink.CFLAGS += -DBOARD_CONFIG=$(BOARD_CFG) $(BOOZ_CFLAGS)
 test_downlink.CFLAGS += -DPERIPHERALS_AUTO_INIT
 test_downlink.srcs   += $(SRC_BOOZ_TEST)/booz2_test_downlink.c
 test_downlink.CFLAGS += -DUSE_LED
 test_downlink.CFLAGS += -DPERIODIC_TASK_PERIOD='SYS_TICS_OF_SEC((1./10.))' -DTIME_LED=1
 test_downlink.srcs   += sys_time.c $(SRC_ARCH)/sys_time_hw.c $(SRC_ARCH)/armVIC.c
 #
 test_downlink.CFLAGS += -DUSE_UART1 -DUART1_BAUD=B57600
 test_downlink.srcs   += $(SRC_ARCH)/uart_hw.c
 #
 test_downlink.CFLAGS += -DDOWNLINK -DDOWNLINK_TRANSPORT=PprzTransport -DDOWNLINK_DEVICE=Uart1 
 test_downlink.srcs   += downlink.c pprz_transport.c

FIXME: More on this when syntax highlighting/line numbering works

The command line to compile the "test_downlink" target for the BOOZ2_A1 aircraft would be

make AIRCRAFT=BOOZ2_A1 test_downlink.compile

and to upload this program to your board ( you don't really need to type the previous command, make is smart and will compile your program if needed when you ask him to upload it )

make AIRCRAFT=BOOZ2_A1 test_downlink.upload

test_max1168

the max1168 is the 16 bits analog to digital converter chip used on the IMU to sample gyros and accels.

make AIRCRAFT=BOOZ2_A1 test_max1168.upload