Booz

Running a simulator : quick start guide

• Extract a copy of paparazzi3 svn

 svn co svn://svn.savannah.nongnu.org/paparazzi/paparazzi3/trunk paparazzi3

• Install all required dependancies

apt-get install paparazzi-dev libtool

• Compile JSBSIM

 cvs -z3 -d:pserver:anonymous@jsbsim.cvs.sourceforge.net:/cvsroot/jsbsim co -P JSBSim 
 cd JSBSim
 ./autogen.sh
 ./configure --enable-maintainer-mode --enable-compile-warnings --enable-libraries --enable-shared --prefix=/opt/jsbsim
 make
 sudo make install

here is a patch to silent warnings

• Compile paparazzi

 cd paparazzi3/trunk
 make

• Compile the vehicle

 make AIRCRAFT=BOOZ2_A1 clean_ac sim

• Start paparazzi_center if you want click to start programs

./paparazzi

• Start messages to watch the middleware activity ( from the tool menu of paparazzi center) or with

./sw/ground_segment/tmtc/messages 

• Start the sim

LD_LIBRARY_PATH=/opt/jsbsim/lib ./var/BOOZ2_A1/sim/simsitl

You should now see activity in the "messages" window

• Plot the value of a message field.

start 'plotter' ( from the tool menu of paparazzi center) or with

 ./sw/logalizer/plotter

for example drag the label 'int32 phi' from the BOOZ2_FP message to the drawing area of the plotter

• Use the datalink to change the temetry mode

start 'settings' ( from the tool menu of paparazzi center) or with

 ./sw/ground_segment/tmtc/settings -ac BOOZ2_A1

start 'server' to dispatch datalink messages ( from the tool menu of paparazzi center) or with

./sw/ground_segment/tmtc/server 

change the field "telemetry" on the first page to "Att loop" and send by pressing the green check button. THe label on the left or the drop box should change to "Att loop" confirming your essage has been received. "message" should now show that the message "BOOZ2_STAB_ATTITUDE" is received

• Use flightgear to visualize your vehicle

If you want a view of a quadrotor in flightgear, make a link from

/usr/share/games/FlightGear/Models/Aircraft/paparazzi to PAPARAZZI_SRC/conf/simulator/flightgear/

start flighgear with

fgfs --fdm=null --native-gui=socket,in,30,,5501,udp --prop:/sim/model/path=Models/Aircraft/paparazzi/mikrokopter.xml

restart your simulator with

 LD_LIBRARY_PATH=/opt/jsbsim/lib ./var/BOOZ2_A1/sim/simsitl --fghost 127.0.0.1

• Save you session

Tunning the attitude control loop

Here we are going to use the simulator to demonstrate a way of tunning the attitude control loop.

• Restart your previous session

• Set telemetry mode to "Att loop"

• Display two real time plotter windows

In the first one, plot the field "m_phi" from the "BOOZ2_STAB_ATTITUDE" message. This is our estimation of roll angle. On top of that, plot the field "phi" from the "BOOZ2_STAB_ATTITUDE_REFERENCE" message. This is our reference roll angle, that is, the roll value we are trying to achieve.

In the second plotter, plot the fields "delta_a_fb" and "delta_a_ff". Those are respectively the feddback and feedforward part of our roll command. The sum of those two terms is what is used as roll command.The feedforward part is the part used to follow our trajectory and the feedback part is the part used to reject perturbations.

• In "Settings", go to the "Att Loop" tab

We notice that the vehicle doesn't follow accurately the step trajectory we are trying to make him do.

Start by setting the value of the proportional gain ('pgain_phi') to 1000 instead of 400. The vehicle now follows the trajectory faster but overshoots. To prevent that, increase the value of the derivative gain ('dgain p') from -300 to -700.

If you look at the plotter where you're ploting the commands, you'll notice that during steps, the feedback command has to work hard. This means that our feedforward command is badly tunned, and namely not working hard enough.Increase the value of the feedforward gain ('ddgain p') from 300 to 540. You'll notice that now the feedback command has becomed marginal during the steps. This is the right value for the gain. Anything bigger will make the feedback command fight against the feedforward command during steps, anything smaller will make the feedback command have to complement the feedforward command.

And by now, you should have found the rounding bug I'm fighting with