View source for Setting up a build environment for overo-oe

follow the instructions on his page:

http://www.gumstix.net/Documentation/view/Overo-Setup-and-Programming/Setting-up-a-build-environment/109.html

(you need a lot of space to reduce the amount of space needed insert 

INHERIT += "rm_work" 

to overo-oe/build/conf/local.conf)

when you are at the command:

$ bitbake omap3-console-image  (when you are in a virtual box environment it will take long 12 hours at least)

and build it on Ubuntu 10.04 LTS - the Lucid Lynx - release you will get this error:

ERROR:
....expat_2.0.1.bb do_unpack failed 

solution to this error:

http://www.facebook.com/note.php?note_id=398968379361

follow instructions of ERROR#1

== patching the kernel for spidev ==


You can follow the [http://www.gumstix.net/Setup-and-Programming/view/Overo-Setup-and-Programming/Setting-up-a-build-environment/111.html instructions] on gumstix's website to build a complete cross development environment. Paparazzi's Makefile will default to look for it in /overo-oe

Work is in progress to offer a pre-compiled cross compilation toolchain.

For the moment compiling omap-console-image will generate the cross compiler and libs you need. You also need to compile libevent which is not compiled by omap-console-image (   [[bitbake libevent]] )

patching the kernel for spidev -- look where kernel comes from in
   /overo-oe/org.openembedded.dev/recipes/linux/linux-omap3_2.6.32.bb

        git clone git://www.sakoman.com/git/linux-omap-2.6.git

        git checkout d434b954906c4f3e356d64d6b49675c601456f51

        place the following patch into /overo-oe/org.openembedded.dev/recipes/linux/linux-omap3-2.6.32/overo/add-spidev-for-mcspi1.patch


   diff --git a/arch/arm/mach-omap2/board-overo.c b/arch/arm/mach-omap2/board-overo.c
   index 165b6bd..fbe3be4 100644
   --- a/arch/arm/mach-omap2/board-overo.c
   +++ b/arch/arm/mach-omap2/board-overo.c
   @@ -625,6 +625,14 @@ static struct spi_board_info overo_spi_board_info[] __initdata = {
                    .mode                        = SPI_MODE_3,
            },
    #endif
   +     {
   +               .modalias       = "spidev",
   +               .max_speed_hz   = 48000000, //48 Mbps
   +               .bus_num        = 1,
   +               .chip_select    = 1,
   +               .mode           = SPI_MODE_1,
   +               //               .controller_data        = &spidev_mcspi_config,
   +      },
    };
 
    static int __init overo_spi_init(void)



        remove ads and lgphillips from /overo-oe/org.openembedded.dev/recipes/linux/linux-omap3/overo/defconfig
        really in  /overo-oe/org.openembedded.dev/recipes/linux/linux-omap3-2.6.32/overo/
        edit /overo-oe/org.openembedded.dev/recipes/linux/linux-omap3_2.6.32.bb 
         SRC_URI_append = " \
           file://${BOOT_SPLASH} \
           file://add-spidev-for-mcspi1.patch;patch=1 \
           "


       bitbake -c clean linux-omap3
       bitbake -c configure linux-omap3
       bitbake -c rebuild linux-omap3

       the defconfig I changed is in 
       /overo-oe/tmp/work/overo-angstrom-linux-gnueabi/linux-omap3-2.6.32-r51/

[[Category:Software]] [[Category:Developer_Documentation]]