KroozSD

From PaparazziUAV
Revision as of 06:18, 26 October 2013 by Softsr (talk | contribs)
Jump to navigation Jump to search

The Krooz Autopilot The Krooz Autopilot The Krooz Autopilot

New KroozSD Version Available!

There is a new version of the KroozSD available - the KroozSD Rotorcraft Edition. Equipped with a quality acceleration sensor from Memsic sensing solutions, it brings one of the best motion sensing performances and vibration immunities in it's class. It ensures much better flight stability and higher immunity to vibration noisy aircrafts. There also added an SWD programming/debugging interface connector to simplify the development of high complicated algorithms. KroozSD R Edition Bott.png KroozSD R Edition Top.png

Overview

KroozSD UAV autopilot board is an all in one rotorcraft solution, with a wide variety of sensors, modules and units on one board in market usual size.

Features

KroozSD is based on the 64 pins STM32F405RGT6 Cortex M4 168MHz processor featuring a Floating point unit (FPU), up to 192k of RAM and 1024k of FLASH.

  • STM32 microcontroller datasheet with 1024kB flash and up to 192kB RAM
  • Onboard microSD card slot (SPI interface)
  • MPU6050 Gyro/Accelerometer sensor and MXR9500 Accelerometer (Rotorcraft Edition).
  • HMC5883 magnet field sensor.
  • MS5611 high precision pressure sensor.
  • XBee Pro module on board connector.
  • MAX7456 OSD module for mixing in a flight data into a camera video screen (using 4 pin connector)
  • 3 x 3.3V TTL UART (5V tolerant)
  • 11 x Servo PPM outputs (or 10 if using PPM output receiver)
  • 2 x I2C 5V bus
  • 1 x SPI bus
  • 5 x Analog input channels
  • 1 x Micro USB
  • Extra camera control 6 pin connector for flexible camera use
  • 3 x status LEDs with attached test point
  • Up to 35V (8S LiPo) input power control unit
  • Up to 1,5A load current on 3,3V line
  • Up to 5A load current on 5V line
  • 50mm x 60mm x 10mm
  • 2 layers PCB design

So, except for a GPS unit with the KroozSD you have all necessary sensors for full features all in one rotorcraft solution.

Flight videos

Here you can see some example flight videos, representing basic KroozSD flight properties:

Windy flight with autonomous landing

Pinout

KroozSD top dscr.png

Usage scenarios

KroozSD can be used in different telemetry versions:

  • with an XBee wireless module connected to the on-board XBee connector

The Krooz Autopilot

  • or without any on-board telemetry solution, with a possibility to connect other telemetry link over one of the UART connectors.

The following picture shows the usage of KroozSD board with I2C bus motor controllers and two camera mount stabilization servos: The Krooz Autopilot

Mechanical Dimensions

KroozSD top dim.png

Schematics

The Krooz Schematics

Programming

The KroozSD autopilot can beprogrammed in different ways:

  • using the pre-loaded KroozDFU USB bootloader over the on-board USB header
  • using the default STM32 serial bootloader over the UART3 connector

Bootloader

The KroozSD uses an own KroozDFU bootloader (based on libopencm3 project). You can find it here, clone to your PC an build or use a precompiled binary file to upload. However the KroozSD board is shipped with the KroozDFU bootloader by default.

Source code

The KroozSD source code is based on Paparazzi master git branch, and ported on the STM32F4 Cortex™-M4 processor family. It is available from here

Where to buy

If you want to buy the KroozSD board, just write me an Email on: softsr@yahoo.de