Search results
Jump to navigation
Jump to search
Page title matches
- [[ATmega_PPM_Encoder_Board|PLEASE USE NEW PPM ENCODER PAGE]] ...eam? Just connect the Ch5 signal from the receiver to the Ch7 input on the encoder.</p>3 KB (454 words) - 20:08, 4 March 2012
- MeekPE is a low cost MCUless PPM Encoder.<br> ...ver without using a microcontroller. The combined signal is input into the PPM input on the Paparazzi controller.<br>9 KB (1,393 words) - 11:55, 14 December 2012
- [[ATmega_PPM_Encoder_Board|PLEASE USE NEW PPM ENCODER PAGE]] ...eam? Just connect the Ch5 signal from the receiver to the Ch7 input on the encoder.</p>5 KB (735 words) - 20:08, 4 March 2012
Page text matches
- *[[RC_Receivers_and_Radios|RC Receivers and Radios<br><small>PPM, PCM and 2.4GHz systems</small>]] *[[PPM_Encoder|PPM Encoder Boards<br><small>Get a PPM signal without any modifications to the receiver</small>]]555 bytes (78 words) - 06:03, 4 March 2016
- [[ATmega_PPM_Encoder_Board|PLEASE USE NEW PPM ENCODER PAGE]] ...eam? Just connect the Ch5 signal from the receiver to the Ch7 input on the encoder.</p>3 KB (454 words) - 20:08, 4 March 2012
- [[ATmega_PPM_Encoder_Board|PLEASE USE NEW PPM ENCODER PAGE]] ...eam? Just connect the Ch5 signal from the receiver to the Ch7 input on the encoder.</p>5 KB (735 words) - 20:08, 4 March 2012
- == PPM Radio Configuration == ...os</tt> directory, contains a description of the radio control transmitter PPM signal. It should follow the grammar described in <tt>radio.dtd</tt>.11 KB (1,724 words) - 08:48, 28 April 2019
- MeekPE is a low cost MCUless PPM Encoder.<br> ...ver without using a microcontroller. The combined signal is input into the PPM input on the Paparazzi controller.<br>9 KB (1,393 words) - 11:55, 14 December 2012
- ** ATMega168 based PPM encoder3 KB (386 words) - 00:45, 24 January 2012
- * 1 x R/C receiver PPM frame input In addition to the classic PPM input, that mostly require receiver modification, one pin of the R/C connec9 KB (1,343 words) - 08:46, 17 July 2015
- A PPM encoder soon appeared after the Paparazzi one. Since APM accepts PPM as separate servo connectors it really is not practical to use one with APM ...lexor for doing this. ENAC has also released a processor-less (MeekPE) PPM encoder as well.11 KB (1,738 words) - 01:06, 17 August 2012
- ...out setting up the Graupner transmitter and receiverand correctly output a ppm sum stream. # CPPM, where the C stands for '''C'''ombined, the PPM sum stream output, supported on all current autopilot boards,27 KB (4,532 words) - 03:05, 3 August 2017
- * 1 x R/C receiver PPM frame input In addition to the classic PPM input, that mostly require receiver modification, one pin of the R/C connec16 KB (2,357 words) - 07:22, 2 August 2018
- # A 2.4 GHz R/C Transmitter and Receiver with a 3-position switch and PPM output for selecting Manual/Stabilized/Auto. ...then decoded by the RF section of the R/C receiver back into the original PPM signal containing 9 servo position PWM values. This signal is normally the19 KB (3,106 words) - 13:57, 1 May 2016
- * 7 x Servo PPM outputs ...ral purpose I/O to be used for PPM input. Additionally [[PPM_Encoder | PPM encoder]] can be used to avoid receiver hardware modification.19 KB (2,935 words) - 19:15, 2 August 2013
- * '''x2 RC Receiver inputs''' <small>''(S.BUS, PPM & Spektrum Satellite compatible, including receiver binding)''</small> ...nd off-the-shelf receivers '''without hardware modification''' or external encoder board:28 KB (4,158 words) - 02:41, 12 April 2018
- * 8 x Servo PPM outputs (only 6 if second I2C (I2C1) bus in use) ...ia.org/wiki/I2c I<sup>2</sup>C] bus (2 x when using only the first 6 Servo PPM outputs)39 KB (6,235 words) - 06:23, 21 February 2020