Difference between revisions of "ImuCalibration/Gyroscopes"
Jump to navigation
Jump to search
| Line 39: | Line 39: | ||
In case of USB 2.0 A-B cable operation, ~/conf/airframes/Poine/turntable.xml has to be amended, as follows, and saved as ~/turntable_dev_usb.xml: | In case of USB 2.0 A-B cable operation, ~/conf/airframes/Poine/turntable.xml has to be amended, as follows, and saved as ~/turntable_dev_usb.xml: | ||
{{Box Code|conf/airframes/Poine/turntable_dev_usb.xml| | {{Box Code|conf/airframes/Poine/turntable_dev_usb.xml| | ||
<pre> | |||
< | |||
main.CFLAGS += -DUSE_USB_SERIAL | main.CFLAGS += -DUSE_USB_SERIAL | ||
main.srcs += $(SRC_ARCH)/usb_ser_hw.c | main.srcs += $(SRC_ARCH)/usb_ser_hw.c | ||
| Line 60: | Line 59: | ||
</airframe> | </airframe> | ||
</pre> | |||
}} | }} | ||
Revision as of 17:26, 9 June 2012
Turntable Procedure
Hardware
Pictures
Turntable rig
IMU cradle view 1.0
IMU cradle view 1.1
Encoder mount base
Olimex LPC H2148
Omron rotary encoder
Components
- audio-technica AT-LP120_USB Direct Drive Professional Turntable
- Olimex LPC H2148
- Omron rotary encoder
- Lisa/L+IMU, Xbee 2.4Ghz modem set, fibreglass mounting plates and general wiring components
Wiring
Encoder to LPC
- Black (common) to EXT2 GND
- Red 5~12 VDC to EXT2 Vin(5v)
- White OUTA to EXT1 PO.22
LPC to LPC
- EXT2 3.3v to EXT1 PO.22 (pull up resistor)
Software
LPC Code Modifications
In case of USB 2.0 A-B cable operation, ~/conf/airframes/Poine/turntable.xml has to be amended, as follows, and saved as ~/turntable_dev_usb.xml:
| File: conf/airframes/Poine/turntable_dev_usb.xml |
main.CFLAGS += -DUSE_USB_SERIAL main.srcs += $(SRC_ARCH)/usb_ser_hw.c main.srcs += $(SRC_ARCH)/lpcusb/usbhw_lpc.c $(SRC_ARCH)/lpcusb/usbinit.c main.srcs += $(SRC_ARCH)/lpcusb/usbcontrol.c $(SRC_ARCH)/lpcusb/usbstdreq.c main.CFLAGS += -DDOWNLINK -DDOWNLINK_TRANSPORT=PprzTransport -DDOWNLINK_DEVICE=UsbS #main.CFLAGS += -DUSE_UART0 -DUART0_BAUD=B115200 #main.srcs += mcu_periph/uart.c #main.srcs += $(SRC_ARCH)/mcu_periph/uart_arch.c #main.CFLAGS += -DDOWNLINK -DDOWNLINK_TRANSPORT=PprzTransport -DDOWNLINK_DEVICE=Uart0 main.srcs += subsystems/datalink/downlink.c subsystems/datalink/pprz_transport.c #main.CFLAGS += -DMB_TACHO #main.srcs += $(MB)/mb_tacho.c </makefile> </airframe>
|