Difference between revisions of "Tiny v2"

From PaparazziUAV
Jump to navigation Jump to search
Line 58: Line 58:
{|border="1"  cellspacing="0" style="text-align:center" cellpadding="6"
{|border="1"  cellspacing="0" style="text-align:center" cellpadding="6"
|+'''SPI'''
|+'''SPI'''
!''Pin #''!!''Name''!!''Type''!!''Desription''!!width="50"|''Suggested Color''
!''Pin #''!!''Name''!!''Type''!!''Description''!!width="50"|''Suggested Color''
|-
|-
|1||GND||PWR||common ground||style="background:black; color:white"|Black
|1||GND||PWR||common ground||style="background:black; color:white"|Black
Line 78: Line 78:
{|border="1"  cellspacing="0" style="text-align:center" cellpadding="6"
{|border="1"  cellspacing="0" style="text-align:center" cellpadding="6"
|+'''PPM'''
|+'''PPM'''
!''Pin #''!!''Name''!!''Type''!!''Desription''!!width="50"|''Suggested Color''
!''Pin #''!!''Name''!!''Type''!!''Description''!!width="50"|''Suggested Color''
|-
|-
|1||GND||PWR||common ground||style="background:black; color:white"|Black
|1||GND||PWR||common ground||style="background:black; color:white"|Black
Line 91: Line 91:
|}
|}
''Note 1 : Used only if servos are connected to the R/C receiver''
''Note 1 : Used only if servos are connected to the R/C receiver''


{|border="1"  cellspacing="0" style="text-align:center" cellpadding="6"
{|border="1"  cellspacing="0" style="text-align:center" cellpadding="6"
|+'''USB'''
|+'''USB'''
!''Pin #''!!''Name''!!''Type''!!''Desription''!!width="50"|''Suggested Color''
!''Pin #''!!''Name''!!''Type''!!''Description''!!width="50"|''Suggested Color''
|-
|-
|1||GND||PWR||common ground||style="background:black; color:white"|Black
|1||GND||PWR||common ground||style="background:black; color:white"|Black
Line 111: Line 112:
|-
|-
|8||ADC_7||IN||Analog to Digital Converter Input #7||
|8||ADC_7||IN||Analog to Digital Converter Input #7||
|}
{|border="1"  cellspacing="0" style="text-align:center" cellpadding="6"
|+'''IRV'''
!''Pin #''!!''Name''!!''Type''!!''Description''!!width="50"|''Suggested Color''
|-
|1||GND||PWR||common ground||style="background:black; color:white"|Black
|-
|2|| +3.3V||PWR||3.3V Rail from Tiny||style="background:red; color:white"|Red
|-
|3||ADC_0||IN||Vertical IR Sensor signal (Analog to Digital Converter Input #0)||style="background:Purple; color:white"|Purple
|}
{|border="1"  cellspacing="0" style="text-align:center" cellpadding="6"
|+'''IRH'''
!''Pin #''!!''Name''!!''Type''!!''Description''!!width="50"|''Suggested Color''
|-
|1||GND||PWR||common ground||style="background:black; color:white"|Black
|-
|2|| +3.3V||PWR||3.3V Rail from Tiny||style="background:red; color:white"|Red
|-
|3||ADC_2||IN||Horizontal IR Sensor signal axis 2 (Analog to Digital Converter Input #2)||style="background:Grey; color:white"|Grey
|-
|4||ADC_1||IN||Horizontal IR Sensor signal axis 1 (Analog to Digital Converter Input #1)||style="background:Sienna; color:white"|Braun
|}
|}

Revision as of 12:55, 9 December 2007

Features

  • Single LPC2148 MCU
  • 8 Analog input channels 0V - 3.3V (2 channels with optional on-board 5v -> 3.3v resistor bridge)
  • 1 3.3V TTL UART (5V tolerant)
  • 8 PWM outputs
  • 1 R/C receiver PPM frame input
  • 1 SPI bus
  • 1 I2C bus
  • 1 USB (client)
  • Integrated GPS receiver and patch antenna (4Hz update)
  • 5V/2.5A switching power supply & 3.3V/1A linear regulator
  • 3 status LEDs with attached test point
  • ?? grams
  • 70.8 x 40mm (smaller then a banking card)
  • 2 layers PCB design, 0603 components

  • Tiny v2.1 top side view

  • Tiny v2.1 bottom side view

The Tiny v2.1 autopilot uses a single Philips LPC2148 ARM7 based microcontroller. The ARM7 is a low-power 32-bit RISC processor core and the Philips LPC2148 has 512KB on-chip Flash ROM, 40KB RAM and can be clocked at 60MHz.

Although critical control code such as the R/C interface and servo output are well segregated in Paparazzi software and well protected from interference from flaws in the stability/navigation/comm/payload code, great care must be taken when experimenting with new software as some errors can cause a the processor to halt or stall for extended periods causing total loss of control.

Architecture

Pinout

Tiny v2-1 pinout.png

Pins Name and Type are specified with respect to the Autopilot Board


SERIAL
Pin # Name Type Description Suggested Color
1 GND PWR common ground Black
2 +5V PWR 5V Rail from Tiny Orange
3 +3.3V PWR 3.3V Rail from Tiny Red
4 DTR
5 CTS
6 RTS
7 RXD1 IN UART1 Serial Input (5V Tolerant) Green
8 TXD1 OUT UART1 Serial Output (5V Tolerant) Blue


SPI
Pin # Name Type Description Suggested Color
1 GND PWR common ground Black
2 +3.3V PWR 3.3V Rail from Tiny Red
3 SSEL IN SSP Slave Select. Selects the SSP interface as a slave (SSEL1)
4 MOSI I/O SPI1 Master Out Slave In. Data output from master or data input to slave
5 MISO I/O SPI1 Master In Slave Out. Data input to master or data output from slave
6 DRDY IN External interrupt 0 input (EINT0)
7 SCK I/O SPI0 Serial clock. Clock output from master or input to slave


PPM
Pin # Name Type Description Suggested Color
1 GND PWR common ground Black
2 +5v PWR 5V Rail from Tiny to R/C receiver supply Red
3 PPM_IN IN PPM Stream from R/C Receiver (5V tolerant) White
4 SERV_RST OUT external PPM decoder reset (Note 1)
5 SERV_CLK OUT external PPM decoder clock (Note 1)

Note 1 : Used only if servos are connected to the R/C receiver


USB
Pin # Name Type Description Suggested Color
1 GND PWR common ground Black
2 +3.3V PWR 3.3V Rail from Tiny Red
3 USB+ I/O USB bidirectional D+ line Green
4 USB- I/O USB bidirectional D- line White
5 VBUS IN Indicates the presence of USB bus power (P0.23) (5V Tolerant) Orange
6 BUTTON IN External Button (+3.3v pullup)
7 LED3 OUT GPIO (LED #3 command)
8 ADC_7 IN Analog to Digital Converter Input #7


IRV
Pin # Name Type Description Suggested Color
1 GND PWR common ground Black
2 +3.3V PWR 3.3V Rail from Tiny Red
3 ADC_0 IN Vertical IR Sensor signal (Analog to Digital Converter Input #0) Purple


IRH
Pin # Name Type Description Suggested Color
1 GND PWR common ground Black
2 +3.3V PWR 3.3V Rail from Tiny Red
3 ADC_2 IN Horizontal IR Sensor signal axis 2 (Analog to Digital Converter Input #2) Grey
4 ADC_1 IN Horizontal IR Sensor signal axis 1 (Analog to Digital Converter Input #1) Braun
Retrieved from "http://wiki.paparazziuav.org/w/index.php?title=Tiny_v2&oldid=2897"