Difference between revisions of "Subsystem/radio control"

From PaparazziUAV
Jump to: navigation, search
m (removed software category, as Subsystems is a subcategory of Software)
Line 62: Line 62:
 
PWM1 and PWM6 should be safe. PWM4 and PWM5 should be OK if you're not using UART1 on the FBW processor - same for PWM2 and PWM3 if you're not using UART0 (disable FBW telemetry for that ).
 
PWM1 and PWM6 should be safe. PWM4 and PWM5 should be OK if you're not using UART1 on the FBW processor - same for PWM2 and PWM3 if you're not using UART0 (disable FBW telemetry for that ).
  
[[Category:Software]] [[Category:User_Documentation]] [[Category:Subsystems]]
+
[[Category:User_Documentation]] [[Category:Subsystems]]

Revision as of 15:31, 1 March 2012

Radio Control subsystem

Currently possible Radio Control subsystems are

  • ppm
  • spektrum
  • datalink (fixedwing only)

Configure Options

If a configure option is not specified the default is used.

  • RADIO_CONTROL_LED: 1, 2, 3, none
    • default: Already defined according to your board (e.g. none for tiny/twog, 1 for booz and navgo).

E.g. if you want to use LED3 to indicate if RC is ok on yapa:

File: conf/airframes/myplane.xml
  <firmware name="fixedwing or rotorcraft">
     ...
    <subsystem name="radio_control"       type="ppm">
      <configure name="RADIO_CONTROL_LED" value="3"/>
    </subsystem>
  </firmware>

Implementations

PPM

The Paparazzi autopilot can interface directly with the PWM signal from any standard hobby R/C receiver. Signal decoding configuration settings for this are stored in the Radio Control file.

Just specify the appropriate subsystem in your firmware section:

File: conf/airframes/myplane.xml
  <firmware name="fixedwing or rotorcraft">
     ...
    <subsystem name="radio_control"     type="ppm"/>
  </firmware>

Spektrum

Datalink

Obsolete Classix Autopilot

If you have a Classix Autopilot:

File: conf/airframes/myplane.xml
 ap.CFLAGS += -DRADIO_CONTROL
 ap.EXTRA_SRCS += radio_control.c $(SRC_ARCH)/ppm_hw.c
 ap.CFLAGS += -DACTUATORS=\"servos_direct_hw.h\"
 ap.EXTRA_SRCS += $(SRC_ARCH)/servos_direct_hw.c

For the Classix, you must specify which pins to use for PWM by adding "-DPWM_SERVO_0, etc." to the line fbw.CFLAGS. This activate the PWM channel.

 wiring on classix PWM connector
 connector   LPC   shared         port 
 PWM1        PWM5  AD1_6  CAP1_3  P0.21
 PWM2        PWM3  RXD0   EINT0   P0.1
 PWM3        PWM1  TXD0           P0.0
 PWM4        PWM6  RXD1   EINT3   P0.9
 PWM5        PWM4  TXD1   AD1_1   P0.8
 PWM6        PWM2  SSEL0  EINT2   P0.7

PWM1 and PWM6 should be safe. PWM4 and PWM5 should be OK if you're not using UART1 on the FBW processor - same for PWM2 and PWM3 if you're not using UART0 (disable FBW telemetry for that ).