Search results

• Module/AOA adc
  Settings file == Airframe Adjustments ==
  2 KB (302 words) - 03:28, 28 November 2017
• Subsystems
  ...uration#Firmware_and_Hardware_definitions|firmware section of the airframe file]]. ...is possible to safely replace ''subsystem'' by ''module'' in your airframe file. The roadmap of Paparazzi is to convert existing subsystems to [[modules]].
  4 KB (547 words) - 03:45, 29 November 2021
• SUMO/logger
  ...and click upload. The configuration can be found as LOGGER in the example file conf/conf.xml.sumo ...ght need to reflash the logger in case you accidently overwrite it with an airframe configuration. That should not happen again as the USB connectors are clear
  3 KB (487 words) - 11:31, 2 February 2014
• Modules
  === In the airframe file === ...ew module for an aircraft, add a section '''modules''' in his airframe xml file :
  10 KB (1,641 words) - 15:23, 17 June 2016
• Community Flight Log Archive
  ** flight description (present textfield at file upload or summary page or both?) *** list of airframe files extracted from logs (stored as files or in git or something?)
  3 KB (424 words) - 06:35, 10 March 2011
• Bixler
  The HobbyKing Bixler is a very inexpensive airframe with very easy flight characteristics and reasonable payload capacity. Its == Airframe configuration ==
  3 KB (577 words) - 23:14, 20 July 2020
• NRAFS
  = Not Really a File System = [[File:NrafsOverview.png]]
  2 KB (368 words) - 05:21, 8 October 2012
• OLSR
  === Airframe configuration === ...ly do by adding to your firmware section the following instructions (in an airframe based on ardrone2_raw.xml for instance):
  2 KB (388 words) - 06:50, 15 April 2015
• Module/Freescale MPL3115A2
  ...the sensors data in the log file set the SENSOR_SYNC_SEND in your airframe file. Every time new data is available it will be sent directly. For pressure re Unfortunately only the raw values are written to the log file (to be changed), they need to be multiplied by the coefficient given in con
  2 KB (349 words) - 19:43, 9 March 2013
• Module/Meas Spec MS5611 I2C
  ...the sensors data in the log file set the SENSOR_SYNC_SEND in your airframe file. Every time new data is available it will be sent directly. ...lues (d1/d2) and the corrected ones (pressure/temp) are written to the log file.
  4 KB (607 words) - 11:22, 21 August 2014
• Settings
  ...located in <tt>conf/settings/</tt>. A <tt>dl_setting</tt> element in this file associates [[GCS#Settings|buttons or sliders in the GCS interface]] to auto .../tt> element allows to specify the corresponding parameter in the airframe file in order to save a tuned value:
  7 KB (1,179 words) - 04:58, 5 December 2015
• Tunnel
  ...of <code>name="setup"</code>. If it doesn't already exist in your airframe file, just add it. ...ollowing command from your paparazzi folder, substituting the name of your airframe and paying attention to case sensitivity:
  5 KB (777 words) - 12:46, 22 November 2017
• Autopilot generation
  ...ilot formal description, included to the [[Airframe_Configuration|airframe file]] and leading to code generation. ...ption is done in a XML file, and when adding the autopilot to the airframe file, C code will be automatically generated and integrated to the airborne code
  9 KB (1,407 words) - 06:18, 15 May 2018
• Twoga-Logga
  [[File:PPRZ_Twoga_Logga_SD_Logger.jpg|200px|thumb|left| Twoga Logga resting after ...ile system. The telemetry data is converted to the standard .data and .log file with a Paparazzi tool. Logging can be started again through a long press of
  2 KB (346 words) - 09:29, 19 November 2015
• Module/VTI SCP1000 I2C
  ...the sensors data in the log file set the SENSOR_SYNC_SEND in your airframe file. Every time new data is available it will be sent directly. Sample log file lines
  2 KB (305 words) - 19:42, 9 March 2013
• SDLogger SPI Direct
  [[File:LisaSD.jpeg|thumbnail|Lisa/SD module]] [[File:Microsd_pinout.png|left|microSD pinout ([http://elasticsheep.com/2010/01/re
  2 KB (390 words) - 07:55, 28 November 2017
• Module/VTI SCP1000 SPI
  ...the sensors data in the log file set the SENSOR_SYNC_SEND in your airframe file. Every time new data is available it will be sent directly. Sample log file lines
  2 KB (293 words) - 19:42, 9 March 2013
• OSAM Tuning Procedure
  ...plane is facing north when the sensor is at 45 degrees (equals a 1 in the airframe config) the thermopile's do not point north south east and west but rather These are set in the AUTO1 section of the airframe file and are the maximum allowed pitch and roll in auto1 mode.. These are by def
  7 KB (1,191 words) - 06:33, 19 September 2020
• ArduIMU
  ...gle.com/p/ardu-imu/wiki/HomePage?tm=6 ArduIMU+ V2 (flat)] into an existing Airframe/Paparazzi-Code. #There is an other airframe/main-AP we wrote which uses a magnetometer for yaw-drift compensation. We h
  7 KB (1,084 words) - 07:45, 1 November 2012
• Cam Footprint
  ...zontal field of view and vertical field of view can be set in the airframe file:
  1 KB (205 words) - 16:22, 18 October 2017

View (previous 20 | next 20) (20 | 50 | 100 | 250 | 500)