Difference between revisions of "STLink"

From PaparazziUAV
Jump to: navigation, search
(Update the ST-Link to blackmagic probe)
(BMP Method)
Line 108: Line 108:
  (gdb) detach
  (gdb) detach
The option bytes do not cover the Readout Protection (RDP), but it seems that this command erases it also.
The option bytes do not cover the Readout Protection (RDP), but the RDP is disabled anyhow...
[[Category:Firmware Flashing]] [[Category:Developer_Documentation]]
[[Category:Firmware Flashing]] [[Category:Developer_Documentation]]

Revision as of 14:36, 24 April 2015


Every STM discovery / eval board comes with a ST-Link V2 on board, with one exception; the STM32VL version comes with a ST-Link V1.

SWD Header

Pinout with Apogee connector

Install Software

The st-flash and st-util tools are needed, provied by texane

Download and compile

$ cd /opt
$ git clone git://github.com/texane/stlink.git stlink
$ cd stlink
$ ./autogen.sh
$ ./configure
$ make

Set enviroment variable

$ exportline="PATH=$PATH:/opt/stlink"
$ if grep -Fxq "$exportline" ~/.profile; then echo nothing to do ; else echo $exportline >> ~/.profile; fi
$ source ~/.profile

Add udev rules

$ sudo cp /opt/stlink/49-stlinkv*.rules /etc/udev/rules.d
$ sudo udevadm control --reload-rules

ST-LinkV1 requires a bit different treatment, read the Readme.txt

Airframe.xml setup

Connect the ST-Link to the MCU. If a complete STM32Fx-Discovery board is used, CN3 jumpers need to be set. To program a external MCU, remove CN3 jumpers and connect the external MCU with the SWD header.

To use SWD via STLink as default:

Update the ST-Link to blackmagic probe

The STM32F103 (STLink MCU) can be flashed with the blackmagic's firware.

Two STLinkV2 Method

Use one STLink to flash another

Hardware Setup: One STLinkV2 (connected via USB) is programming the other one. Change the 4 Solder jumpers on the bottom of the target STLinkV2 from "DEFAULT" to "REVERSED".

Connections between the two STLinks

Connections [Header-Pin]
Use From Programmer To Target
5V P2-5V P2-5V
GND CN2-3 CN3-4

Download and build the Firmware

git clone https://github.com/blacksphere/blackmagic
cd blackmagic
git submodule init
git submodule update
cd src
make clean
make PROBE_HOST=stlink

Remove the readout protection, erase and flash

openocd -f interface/stlink-v2.cfg -f target/stm32f1x_stlink.cfg -c "init" -c "halt" -c "stm32f1x unlock 0" -c "shutdown"
st-flash erase
st-flash --reset write blackmagic.bin 0x8002000
st-flash write blackmagic_dfu.bin 0x8000000


Black Magic Discovery from Esden <-- This also describes how to remove the read out protection.
embdev.net page

BMP Method

Use a BMP to flash a STLink

Transfer the solder jumpers from "Default" to "Reversed" and build the firmware as descibed above.
Connect the BMP to the CN2 header (see Pinout above).

Start gdb, erase the option bytes and flash BMP

(gdb) target extended-remote /dev/ttyACM0
(gdb) mon swdp_scan
(gdb) att 1 
(gdb) mon option erase
(gdb) load /dir/to/blackmagic
(gdb) load /dir/to/blackmagic_dfu
(gdb) detach

The option bytes do not cover the Readout Protection (RDP), but the RDP is disabled anyhow...