Dev/Caspa

From PaparazziUAV
Jump to navigation Jump to search

This page describes the ongoing work to fully integrate a Caspa FS camera on a Lisa/L board. Any advices/suggestions/contributions are welcome.

Final Goal

The final goal is to have a Caspa FS camera connected to the Overo chip on a Lisa/L board. The Overo chip should be able to communicate with the STM32 via SPI. The link shall be used to transmit the result of the image processing computed by the Overo. However this should be flexible enough to let some room for the developer to decide which processing to do and which kind of data to send.

Methods

The following lists the steps that are deemed to be important in achieving the final goal.

  1. Bitbake a kernel for Overo that includes the camera modules and the SPI modules
  2. Bitbake a kernel for STM32 that includes the SPI modules

Caspa camera on an Overo expansion board

As a first step a simple connection between the camera and the Overo was tried using an Overo expansion board, i.e. not the the Lisa/L board.

Hardware components

Step-by-step

Create a bootable MicroSD card if you do not have one

Follow this and use LABEL1 as 'mmcblk0p1' and LABEL2 as 'mmcblk0p2'.

Load a pre-built standard image
wget http://cumulus.gumstix.org/images/angstrom/factory/2011-03-25-1619/omap3-desktop-nand-image-overo-booted.tar.bz2
tar -xf omap3-desktop-nand-image-overo-booted.tar.bz2 -C /media/mmcblk0p2 // the filesystem
wget http://cumulus.gumstix.org/images/angstrom/factory/2011-03-25-1619/MLO
wget http://cumulus.gumstix.org/images/angstrom/factory/2011-03-25-1619/u-boot.bin
wget http://cumulus.gumstix.org/images/angstrom/factory/2011-03-25-1619/uImage
cp MLO /media/mmcblk0p1
cp u-boot.bin /media/mmcblk0p1
cp uImage /media/mmcblk0p1


3. Replace some files to get the camera modules working

Download: http://cumulus.gumstix.org/images/angstrom/misc/caspapx/uImage-2.6.34 http://cumulus.gumstix.org/images/angstrom/misc/caspapx/modules-2.6.34.tgz

Do: $ tar -xf modules-2.6.34.tgz -C /media/mmcblk0p2/ $ cp uImage-2.6.34 /media/mmcblk0p1/uImage $ cp uImage-2.6.34 /media/mmcblk0p2/boot/uImage

4. Attach the camera to the Overo board

Insert the white ribbon cable contact-side-up into the Caspa connector and contact side down into the Overo connector.

5. Insert MicroSD card in the Overo board

6. Set environment variables

Connect the expansion board to the host machine via USB

On the host machine do: sudo apt-get install ckermit $ kermit -l /dev/ttyUSB0 C-Kermit>set flow-control none C-Kermit>set carrier-watch off C-Kermit>set speed 115200 /dev/ttyUSB0, 115200 bps C-Kermit>connect Connecting to /dev/ttyUSB0, speed 115200 Escape character: Ctrl-\ (ASCII 28, FS): enabled Type the escape character followed by C to get back, or followed by ? to see other options.

Power-up the expansion board

Hit 'Enter' to interrupt the boot sequence Type: nand erase 240000 20000 reset Hit 'Enter' to interrupt the boot sequence Type: setenv defaultdisplay lcd43; saveenv; reset

7. Get the image

Let the Overo boot properly Touch the screen and calibrate it as indicated In the serial command line do: overo login: root export DISPLAY=:0.0 mplayer tv:// -tv driver=v4l2:device=/dev/video0 -x 480 -y 272 -vo x11

The camera image should appear in the LCD display

Based on: http://wiki.gumstix.org/index.php?title=Caspa_camera_boards