Difference between revisions of "User:Mcurrie"

From PaparazziUAV
Jump to navigation Jump to search
 
(15 intermediate revisions by the same user not shown)
Line 1: Line 1:
Matthew Currie
== Matthew Currie ==


Located in Nanaimo, B.C. Canada
* IRC Nick: dc3<br/>
* Location: Nanaimo, British Columbia, Canada
* Member Since: November 2006


Currently building building Tiny 1.1 hardware.  Has hot air reflow, solder paste, smt, linux capabilities and keeps stock of some parts on hand.  Let me know if anyone needs any assistance.
Built 13+ Tiny 13 v1.1 autopilot boards in-house.  Distributed boards into the group to break-even.


'''Q:''' [Tiny 1.1] My AP begins executing only after downloading code to it and not after a reset.
=Setup=


'''A:''' Make sure when you compiled your initial USB Bootloader you selected the right USB enable pin.  If using P0.23 add PROC=GENERIC to the make process.
==Airframe and Powerplant==


'''Q:''' [Tiny 1.1] I get error accessing USB when trying to load code to the Autopilot
* Multiplex Funjet
* AXI 2212/26 Brushless "outrunner" Motor
* LiPower Lites 3S1P 2100mAh 18C LiPo Batteries x 2
* APC 9x6E Propeller (checked to draw ~ 11.5A)


'''A:''' You need to copy a USB rules file following the instructions below
==Electronics==


# cd ''[paparazzi3 folder]''
* Castle Creations Phoenix 35 Brushless Speed Control
# cp conf/system/udev/rules/10-paparazzi.rules /etc/udev/rules.d/
* Castle Creations USB Programming Harness
* Berg 4L Receiver modified for PPM stream
* 2x Hitec HS-55 Servos
* Maxstream (now digi) XBee 2.4GHz Pro modems + devkit
* Modified FMA CoPilot XY and Z IR Sensor Boards
* Hitec Eclipse 7 Radio with Spectra PLL Module (btw the Spectra module is HORRIBLE)


'''Q:''' [Tiny 0.9-1.1] What is the command to compile the ARM7 code?
==Production and Tooling==


A: the two relevent commands are below. Replace [AIRCRAFT] with the name of your aircraft.
* Hot Air Reflow Rework Station
* SMT Soldering Station
* Molex PicoBlade Crimpers
* Molex Micro-Fit 3.0 Crimpers
* 10-20 of each of every PicoBlade and MicroFit connectors
* Various Alpha 26 AWG Teflon Hook-up Wire


# cd ''[parazzi3 folder]'''
==Field==
# make AIRCRAFT=[AIRCRAFT] ap.compile


to download code that has already been compiled
* 110Ah Marine Deep Cycle Battery
* Folding Picnic Table (yes, exactly the same as poines!)
* Great Planes Triton multi-chemistry charger
* Custom waterproof data modem enclosure with type-N connector and 25 foot RS232 cable
* Various Pelican transport cases


# cd ''[parazzi3 folder]'''
==Current Progress==
# make AIRCRAFT=[AIRCRAFT] ap.upload


'''Q:''' How do I get GCS to talk to the AP with straight serial and not a modem?
* Airframe / Ground Station Complete
* Basic AUTO1 tuning, not satisfactory, will continue


'''A:''' Here is an example of a section of my paparazzi3/conf/control_panel.xml
==ToDo==


<session name="4 Matt Flight">
* Order 12 dBi yagi
  <program name="link">
    <arg flag="-d" constant="/dev/ttyUSB0"/>
    <arg flag="-transport" constant="pprz"/>
    <arg flag="-uplink" constant=""/>
  </program>
  <program name="server"/>
  <program name="gcs"/>
</session>


'''Q:''' How do I load the USB Bootloader onto the Tiny?


'''A:''' Start by wiring up 3.3V RS232 from the PC to the Tiny. 
[[Category:Members]]
 
The serial lines on the ARM7 micro are 5V tolerant so if it helps cut down on complexity/parts you could use 5V RS232 for this.  ''Optional: You could also form a basic resistor voltage divider on the PC TX -> AP RX''
 
*PC SERIAL_TX -> LPC_RXD_0 (SERIAL_1-7)
*PC SERIAL_RX -> LPC_TXD_0 (SERIAL_1-8)
*PC SERIAL_GND -> GND (SERIAL_1-1)
*LPC_P0.14 (SERIAL_1-5) must be asserted low (held to ground) while the Tiny powers up in order to enter the Serial Boot Loader.  (You could also wire this to a pushbutton which ties it to ground, holding this button briefly while you power up the AP.  This pin does not need to stay low during the programming or any time afterwards)
 
once these connections have been made, execute this command in a console
 
# make PROC=GENERIC upload_bl

Latest revision as of 15:51, 11 October 2009

Matthew Currie

  • IRC Nick: dc3
  • Location: Nanaimo, British Columbia, Canada
  • Member Since: November 2006

Built 13+ Tiny 13 v1.1 autopilot boards in-house. Distributed boards into the group to break-even.

Setup

Airframe and Powerplant

  • Multiplex Funjet
  • AXI 2212/26 Brushless "outrunner" Motor
  • LiPower Lites 3S1P 2100mAh 18C LiPo Batteries x 2
  • APC 9x6E Propeller (checked to draw ~ 11.5A)

Electronics

  • Castle Creations Phoenix 35 Brushless Speed Control
  • Castle Creations USB Programming Harness
  • Berg 4L Receiver modified for PPM stream
  • 2x Hitec HS-55 Servos
  • Maxstream (now digi) XBee 2.4GHz Pro modems + devkit
  • Modified FMA CoPilot XY and Z IR Sensor Boards
  • Hitec Eclipse 7 Radio with Spectra PLL Module (btw the Spectra module is HORRIBLE)

Production and Tooling

  • Hot Air Reflow Rework Station
  • SMT Soldering Station
  • Molex PicoBlade Crimpers
  • Molex Micro-Fit 3.0 Crimpers
  • 10-20 of each of every PicoBlade and MicroFit connectors
  • Various Alpha 26 AWG Teflon Hook-up Wire

Field

  • 110Ah Marine Deep Cycle Battery
  • Folding Picnic Table (yes, exactly the same as poines!)
  • Great Planes Triton multi-chemistry charger
  • Custom waterproof data modem enclosure with type-N connector and 25 foot RS232 cable
  • Various Pelican transport cases

Current Progress

  • Airframe / Ground Station Complete
  • Basic AUTO1 tuning, not satisfactory, will continue

ToDo

  • Order 12 dBi yagi
Retrieved from "http://wiki.paparazziuav.org/w/index.php?title=User:Mcurrie&oldid=5615"