Difference between revisions of "Lisa"

From PaparazziUAV
Jump to navigation Jump to search
m (typo)
 
(162 intermediate revisions by 17 users not shown)
Line 1: Line 1:
Lisa ( the Lost Illusions Serendipitous Autopilot) is a [http://www.st.com/mcu/inchtml-pages-stm32.html STM32]/[http://www.gumstix.net/Setup-and-Programming/cat/Overo-Setup-and-Programming/111.html Overo] board designed to run Paparazzi
<categorytree style="float:right; clear:right; margin-left:1ex; border: 1px solid gray; padding: 0.7ex;" mode=pages>Autopilots</categorytree>
__TOC__
Lisa ( the Lost Illusions Serendipitous Autopilot) is a range of autopilots based on [http://www.st.com/mcu/inchtml-pages-stm32.html STM32] microcontrollers ( CortexM3@72Mhz ) designed to run Paparazzi.
There's no such thing as a perfect autopilot, only autopilots adapted to a particular purpose. This is the reason why the Lisa autopilots come in different styles for different uses.


== TODO ==
The first members of the family are:


List of files currently being edited:
*Lisa/L, a design where the STM32 is associated to a gumstix [http://www.gumstix.net/Setup-and-Programming/cat/Overo-Setup-and-Programming/111.html Overo].
* Lisa Schematic
*Lisa/M, a design focusing on cost and simplicity.
* booz.lbr
*Lisa/S, a design focusing on size and weight.


==Lisa/L==


Antoine:
=== Description ===
* <strike>check JTAG on STM32</strike>
* work with Piotr on connecting the missing wires on the STM
* I2C on STM32:
* SPI on STM32:
* USB for gumstix : does 5V need to be switchable ? (to allow reset from the gumstix)
* Todo's from sheet 3
* Check's from sheet 5
* Pressure sensor instruction to gany (redo airspeed computation), so he can finish the schematic for that (or finish it directly in the schematic)
* Check the routing rules below and add if planned on routing a certain part in a specific way


[[Lisa/L]] is a dual processor board autopilot designed to allow for the possibility of using Linux for Paparazzi airborne code.


Esden:
[[Image:lisa_l_bloc_diag_simple.png|360px]]
* <strike>STM32 spelling and connection check</strike>
[[Image:lisa_l_top.png|360px]] [[Image:lisa_l_bot.png|360px]]
* <strike>Fix STM32 footprint pad sizes</strike>
* <strike>Routing rules that have to be followed</strike>
* <strike>Add specification of external pressure sensor ADC</strike>
* howto for STM32 gcc gdb toolchain (blinking LED or similar) (started writing one on [http://openhardwarewiki.org/wiki/Summon_ARM_Toolchain openhardwarewiki.org])


=== Documentation ===


Gany:
The documentation for Lisa/L is broken into several parts due to board complexity and Gumstix [[Overo]] integration.
* <strike>Check FT2232 footprint hw/lbr/booz.lbr  qfn-64 size & pinout
* [[Lisa/L|Main Documentation]] - primary hardware documentation and intro to software
** -> Changed pad size from 0.6 x 0.4  to  0.75 x 0.25  and moved pin1 indicator outside the chip. </strike> 
* [[Dev/LisaL|Additional Developer Documentation]] - additional advanced hardware and software documentation and notes
* <strike>Make sure STM32 can interrupt overo
* [[LisaL_Gallery|Lisa/L Photo Gallery]] - pictures of [[Lisa/L]]
** -> connected omap pin 176 with stm pin 11 via level shifter</strike>
* [[User/LisaL/Tutorial/Quadrocopter|Unfinished Rotorcraft Tutorial]] - rotorcraft tutorial, needs considerable work
* Place components
* [[User/LisaL/Tutorial/FixedWing|Unfinished Fixedwing Tutorial]] - fixedwing tutorial, needs considerable work
* Route board
* [[OMAP|Gumstix Integration Intro]] - intro and documentation listing for integrating a Gumstix Overo with [[Lisa/L]], including for USB devices and cameras
* Send for production 4pcb/pcbcard(china)/sunstone


== Lisa/M ==


=== Description ===


== Hardware ==
[[Lisa/M]] is a great general purpose small-footprint autopilot. There are currently two versions that have been produced. Detailed documentation can be found here:
* [[Lisa/M_v2.0|Lisa/M v2.0 (current) Documentation]]


The hardware is still in development. The current CAD files are maintained in savannah svn in the paparazzi4/trunk/hw/lisa directory.
[[Image:LisaM_V2_0_TopView.JPG|360px|Lisa/M v2.0 Top View]]
Software development is done on a Overo/Summit + Olimex STM32-H103 dev board
[[Image:lisa_proto.jpg|thumb]]


=== STM32 ===


STM32-F103 ( esden can you write the name of the actual chip we're using ? 64 pins the most ram and flash ? )
* [[Lisa/M_v1.0|Lisa/M v1.0 Documentation]]


==== pinout ====
[[Image:lisa_m_top_small.png|360px|Lisa/M v1.0 Top View]]


SPI1 :  IMU/baro high speed sensor communications, STM32 is mater
=== Usage scenarios ===
        pin 21 (SCK), 22(MISO), 23(MOSI) 
        accel/gyro 16bitsADC  9(DRDY)  8(SS)
        mag                  24(DRDY) 10(SS)  25(RESET)
        eeprom                        53(SS)
        baro                  40(DRDY) 39(SS)


SPI2 :  overo, STM is slave
There are many potential applications for the small, relatively inexpensive and flexible [[Lisa/M]]. For regular Autopilot boards a fully equip [[Lisa/M]] board is needed. For some scenarios just a basic [[Lisa/M]] without an [[Inertial_Measurement_Units|IMU]] and barometric pressure sensor is needed, which reduces the board cost. Here are some ideas (not all have yet to be implemented):
        pin 33 (SS), 34(SCK), 35(MISO), 36(MOSI),  11(interrupt for OMAP)


I2C1 :  motorcontroller
* As a basic Autopilot
        pin 58(SCL), 59(SDA)
** To use the [[Lisa/M]] as an autopilot, you need to attach a GPS receiver. A nice [[GPS#u-Blox_LEA_Series_Receivers|uBlox LEA-5H]] or newer will perform great.
* As an advanced Autopilot
** Additional sensors for measuring airspeed, current, etc. would enhance a fixed-wing airframe.
* As a servo extender
** Sometimes being able to control seven actuators is just not enough. Large airframes may require flaps or an airbrake and automatic landing facilities. Maybe special ACL/Nav lights, or four cameras with zoom. By using a coupled second basic [[Lisa/M]] and connecting this to the master Autopilot board we can extend the amount of servos. Large airframes can also benefit from remote and/or redundant servo drivers.
* As a Safety Pilot Device
** To provide an extra safety level required in some UAS challenges. A second [[Lisa]] board can make it easy to adhere to the rules for such a challenge.
* As a Data Logger
** Maybe you have a need only to log all kinds of data, like temperature, volts, amps, height, airspeed, and not control the aircraft. For this we can setup a [[Lisa/M]] board. Collecting this data can be to a storage medium like on a micro SD card. Sometimes there is no need for real-time data collection through telemetry but just for storing a huge dataset.
* As a Camera controller
** On some models that do not require many servos (for example - flying wing with only 3 channels used), spare channels can be used for camera control. In addition, it could be used as an independent pan-tilt unit (PTU) controller.
* As a Airframe Tracker
** Tracking an airframe for an antenna or camera on a tripod is one of the many optional uses for a [[Lisa/M]] Board.


I2C2 : extension
== Lia ==
      pin 29(SCL), 30(SDA)


UART1 : GPS or IMUxsense
Lia is a lower-cost variant of Lisa/M 2.0. The microcontroller, basic layout, servo outputs, and mounting holes are the same. Major differences:
      pin 42(TX), 43(RX)  
* 0.1" through-hole connections for non-servo I/O instead of Molex picoblade
** PCB size increased slightly to (58x34mm) to accommodate throughholes
* CAN transceiver removed on initial units; populated on later units (see [http://paparazzi.enac.fr/wiki/Lia documentation])
* barometer removed
* I2C level shifter removed
* 5V voltage regulator removed
* Added provisions for multiple BEC input balancing on servo connectors


UART2 : Modem
[[Image:Lia_1.1_top.jpg|360px|Lia v1.1 Top View]]
      pin 16(TX) ,17(RX)


UART3 : RC24
      pin 51(TX), 52(RX)


CAN : motor controller
[[Lia|Lia documentation]]
      pin 42(TX), 43(RX)


SERVO_out: driving 3 servos
== Lisa/S ==
      37(TIM3CH1), 38(TIM3CH2), 26(TIM3CH3)


RC_in: analog RC
Lisa/S is very small autopilot board. The focus for this design is size, weight and power consumption. It's an autopilot suited for the smallest airframes.
      27(TIM3H4)


JTAG : flash and debug
[[Image:Lisa_S_V0_1_r2_on_finger.jpg|360px]]
      46(TMS), 49(TCK), 50(TDI), 55(TDO), 56(TRST), 7(RESET)


ADCs : 1 for battery 2/3 for extansion
* [[Lisa/S|Lisa/S Documentation]]
     
LED :
      3(LED_CLK), 4(LED_DATA)


=== Pressure sensors ===


The board will be equipped with a pair of pressure sensors, one absolute to measure altitude and one differential to measure airspeed.
[[Category:Lisa]] [[Category:User_Documentation]] [[Category:Autopilots]]
 
==== Absolute Pressure ====
The proposed absolute pressure sensor is the freescale [http://www.freescale.com/webapp/sps/site/prod_summary.jsp?code=MPXx6115&fsrch=1 MPXh6115]
The following plot displays the output of the sensor versus altitude
 
[[Image:absolute_pressure.png]]
 
==== Differential Pressure ====
 
The proposed differential sensor is the [http://www.freescale.com/webapp/sps/site/prod_summary.jsp?code=MPXx5004&fsrch=1 MPXV5004DP]
 
[[Image:differential_pressure.png]]
 
Because of high resolution requirements in the pressure sensor circuit there is an external ADC needed with the following features:
* 16bit resolution minimum, 20bit would be awesome
* Two channels (multiplexed or not) each at least 100Hz sampling rate
* I2C or SPI interface (I2C preferred)
** We used the [http://www.maxim-ic.com/quick_view2.cfm/qv_pk/4950 MAX11040] as ADC for a meteo payload, some (SPI) code is there. It samples 4 channels simultaneously in 24 bits (less "in real"). Slowest conversion speed is 250.1 samples/second.
 
== Software ==
 
=== STM32 drivers for paparazzi ===
 
UART : done without DMA, so got datalink, telemetry and RC24 working
 
I2C : not done, needed for motor controllers
 
SPI : not done, needed for IMU ( big works as we share with mag and baro) and for overo
 
CAN : not don, needed for motor controller and CSC
 
PPMin: not done, needed for analog radio control and windvane
 
PPMout: not done, needed for servos ( 3 servos ? )
 
=== STM32 toolchain ===
 
You can use the [http://github.com/esden/summon-arm-toolchain summon-arm-toolchain] script to build the required toolchain.
For the default values of the Paparazzi Makefile to work, you should set
 
<code>
PREFIX=/opt/stm32/toolchain/arm-elf
</code>
and
<code>
LIBSTM32_EN=1
</code>
 
=== Open Embedded ===
 
Open Embedded is the linux distribution used on the overo.
You can follow the [http://www.gumstix.net/Setup-and-Programming/view/Overo-Setup-and-Programming/Setting-up-a-build-environment/111.html instructions] on gumstix's website to build a complete cross development environment. Paparazzi's Makefile will default to look for it in /overo-oe
 
 
== Status ==
 
== Routing Rules ==
 
* 6mil traces/spacings for signals
* 12mil traces/spacings for power traces (this is min value, otherwise as wide as possible or even planes if possible)
* 6mil layout grid
* Layer stacking:
** Top: Signal + Ground plane
** Route2: Ground plane(s) (Separate analogue and digital ground)
** Route15: Power plane(s)
** Bottom: Signal + Ground plane
* 0.4mm vias with 0.1mm restring

Latest revision as of 08:51, 7 January 2016

Autopilots
Booz
HB Autopilots
Lisa
Tiny
YAPA Autopilots
Ap.parrot minidrone
Apogee/v1.00
HITL
Autopilots
Bebop
Booz
Chimera/v1.00
Classix
CrazybeeF4Pro
Disco
Elle
Elle0
Future Autopilots
Krooz
KroozSD
LinAM V4
Lisa
Lisa/Bone
Lisa/L
Lisa/M
Lisa/M v1.0
Lisa/M v2.0
Lisa/MX
Lisa/S
NavGo v3
NavStik
Pixhawk
Pixracer
Previous Autopilots
STM32F4 Discovery
STM32F429I Discovery
Tawaki/v1.00
Tawaki/v1.10
TWOG/v1.0
Umarim Lite v2
Umarim v1.0
Xvert

Lisa ( the Lost Illusions Serendipitous Autopilot) is a range of autopilots based on STM32 microcontrollers ( CortexM3@72Mhz ) designed to run Paparazzi. There's no such thing as a perfect autopilot, only autopilots adapted to a particular purpose. This is the reason why the Lisa autopilots come in different styles for different uses.

The first members of the family are:

  • Lisa/L, a design where the STM32 is associated to a gumstix Overo.
  • Lisa/M, a design focusing on cost and simplicity.
  • Lisa/S, a design focusing on size and weight.

Lisa/L

Description

Lisa/L is a dual processor board autopilot designed to allow for the possibility of using Linux for Paparazzi airborne code.

Lisa l bloc diag simple.png Lisa l top.png Lisa l bot.png

Documentation

The documentation for Lisa/L is broken into several parts due to board complexity and Gumstix Overo integration.

Lisa/M

Description

Lisa/M is a great general purpose small-footprint autopilot. There are currently two versions that have been produced. Detailed documentation can be found here:

Lisa/M v2.0 Top View


Lisa/M v1.0 Top View

Usage scenarios

There are many potential applications for the small, relatively inexpensive and flexible Lisa/M. For regular Autopilot boards a fully equip Lisa/M board is needed. For some scenarios just a basic Lisa/M without an IMU and barometric pressure sensor is needed, which reduces the board cost. Here are some ideas (not all have yet to be implemented):

  • As a basic Autopilot
    • To use the Lisa/M as an autopilot, you need to attach a GPS receiver. A nice uBlox LEA-5H or newer will perform great.
  • As an advanced Autopilot
    • Additional sensors for measuring airspeed, current, etc. would enhance a fixed-wing airframe.
  • As a servo extender
    • Sometimes being able to control seven actuators is just not enough. Large airframes may require flaps or an airbrake and automatic landing facilities. Maybe special ACL/Nav lights, or four cameras with zoom. By using a coupled second basic Lisa/M and connecting this to the master Autopilot board we can extend the amount of servos. Large airframes can also benefit from remote and/or redundant servo drivers.
  • As a Safety Pilot Device
    • To provide an extra safety level required in some UAS challenges. A second Lisa board can make it easy to adhere to the rules for such a challenge.
  • As a Data Logger
    • Maybe you have a need only to log all kinds of data, like temperature, volts, amps, height, airspeed, and not control the aircraft. For this we can setup a Lisa/M board. Collecting this data can be to a storage medium like on a micro SD card. Sometimes there is no need for real-time data collection through telemetry but just for storing a huge dataset.
  • As a Camera controller
    • On some models that do not require many servos (for example - flying wing with only 3 channels used), spare channels can be used for camera control. In addition, it could be used as an independent pan-tilt unit (PTU) controller.
  • As a Airframe Tracker
    • Tracking an airframe for an antenna or camera on a tripod is one of the many optional uses for a Lisa/M Board.

Lia

Lia is a lower-cost variant of Lisa/M 2.0. The microcontroller, basic layout, servo outputs, and mounting holes are the same. Major differences:

  • 0.1" through-hole connections for non-servo I/O instead of Molex picoblade
    • PCB size increased slightly to (58x34mm) to accommodate throughholes
  • CAN transceiver removed on initial units; populated on later units (see documentation)
  • barometer removed
  • I2C level shifter removed
  • 5V voltage regulator removed
  • Added provisions for multiple BEC input balancing on servo connectors

Lia v1.1 Top View


Lia documentation

Lisa/S

Lisa/S is very small autopilot board. The focus for this design is size, weight and power consumption. It's an autopilot suited for the smallest airframes.

Lisa S V0 1 r2 on finger.jpg

Retrieved from "http://wiki.paparazziuav.org/w/index.php?title=Lisa&oldid=20721"