Difference between revisions of "CrazybeeF4Pro"

From PaparazziUAV
Jump to navigation Jump to search
(Created page with "=Crazybee F4 Pro= Category:Autopilots")
 
m
Line 1: Line 1:
=Crazybee F4 Pro=
=Crazybee F4 Pro=
=About=
The Crazybee F4 Pro Flightcontroller is a redesign of a common F4 FC. There are different models with an embedded as the radio receiver, and 4in1 ESC are all integrated into one single board. The Crazybee F4 Pro has embedded ESC to drive 4x brushless motors as found on small raceingquadcopters like the [[Trashcan | ]]
=Specifications=
PH2.0 battery connector
=Variations=
The Flightcontroller exists in four different PCB variations
* CrazyBeeF4FRPro for use with Frsky
* CrazyBeeF4DXPro for use with Spektrum
* CrazyBeeF4Pro Without receiver
* CrazyBeeF4FSPro with Nordic chip for Flysky
==Versions==
There are different versions of almost the same board V1,V2, V2.1  and V3. The differences in the table below:
=Issues=
Spiking power on the board when plugging in a 2s battery could lead to a broken board on the original design. To preven this from happening as add a capacitor to the battery lead. This capacitor should have an ESR lower than 0.2ohm and have a capacitance of 100uF or higher. A Rubycon ZLG/ZLH series and Samyoung NXB series.
=Connect additional devices=
==Telemetry==
===Wifi Module===
==JeVois camera==
=Binding=
To bind with your TX follow these steps
1. Connect battery
1. Pres an hold the bind button for about 2 seconds until the LED lits continuous
1. Enter the bind mode via your transmitter menu or bind button
1. The LED starts blinking as soon as binding was successful
1. Unpower battery, repower, start flying
=Suppliers=
One can buy one here:
!More
This wiki is not the only place to get some info about the Hardware ofcourse. [[http://ardupilot.org/copter/docs/common-pixracer-overview.html | Here]] some more.
!Airframe
An airframe using this board is:
* OpenUAS Trashcan
!Links
[[Category:Autopilots]]
[[Category:Autopilots]]

Revision as of 04:02, 17 December 2019

Crazybee F4 Pro

About

The Crazybee F4 Pro Flightcontroller is a redesign of a common F4 FC. There are different models with an embedded as the radio receiver, and 4in1 ESC are all integrated into one single board. The Crazybee F4 Pro has embedded ESC to drive 4x brushless motors as found on small raceingquadcopters like the

Specifications

PH2.0 battery connector

Variations

The Flightcontroller exists in four different PCB variations

  • CrazyBeeF4FRPro for use with Frsky
  • CrazyBeeF4DXPro for use with Spektrum
  • CrazyBeeF4Pro Without receiver
  • CrazyBeeF4FSPro with Nordic chip for Flysky

Versions

There are different versions of almost the same board V1,V2, V2.1 and V3. The differences in the table below:

Issues

Spiking power on the board when plugging in a 2s battery could lead to a broken board on the original design. To preven this from happening as add a capacitor to the battery lead. This capacitor should have an ESR lower than 0.2ohm and have a capacitance of 100uF or higher. A Rubycon ZLG/ZLH series and Samyoung NXB series.

Connect additional devices

Telemetry

Wifi Module

JeVois camera

Binding

To bind with your TX follow these steps

1. Connect battery 1. Pres an hold the bind button for about 2 seconds until the LED lits continuous 1. Enter the bind mode via your transmitter menu or bind button 1. The LED starts blinking as soon as binding was successful 1. Unpower battery, repower, start flying

Suppliers

One can buy one here:

!More

This wiki is not the only place to get some info about the Hardware ofcourse. [| Here] some more.

!Airframe

An airframe using this board is:

  • OpenUAS Trashcan

!Links