User:TimHansen - Revision history

TimHansen: VirtualBox

2012-04-06T09:00:47Z

VirtualBox

← Older revision		Revision as of 03:00, 6 April 2012
Line 34:		Line 34:

	I hope that this is all that has to be done.		I hope that this is all that has to be done.

			== VirtualBox ==
			Using Paparazzi in VirtualBox under Windows:
			* VirtualBox 4.1.12 for Windows hosts
			* VirtualBox 4.1.12 Oracle VM VirtualBox Extension Pack
			* Debian Squeeze
			* Turn on USB 2.0 in VirtualBox configuration
			* Set a Filter for a USB Device (otherwise VirtualBox crashes)

Flixr: /* uBlox GPS 5H */

2010-12-28T22:02:35Z

uBlox GPS 5H

← Older revision		Revision as of 16:02, 28 December 2010
Line 13:		Line 13:
	Invalid_argument("Latlong.of_utm")		Invalid_argument("Latlong.of_utm")

			[[User:Flixr\|flixr]] 23:02, 28 December 2010 (CET) You do '''not''' have to add the define GPS_USE_LATLONG, just use the proper gps subsytem:
			<subsystem name="gps" type="ublox_lea5h"/>

	== Sound Output ==		== Sound Output ==

TimHansen: MX-12 3 state switch

2010-12-28T16:27:03Z

MX-12 3 state switch

← Older revision		Revision as of 10:27, 28 December 2010
Line 23:		Line 23:
	<define name="TELEMETRY_MODE_FBW" value="1"/>		<define name="TELEMETRY_MODE_FBW" value="1"/>
	to the firmware section.		to the firmware section.

			== Using Graupner MX-12 for paparazzi ==
			The MX-12 has 6 channels but no 3 state switch. To use it together with paparazzi I used a trick. I used the integrated mixer to mix 2 switches together into 1 channel. One swiches Auto2 on and off. The other switches between Manual and Auto1. The mixer setup is as following:

			MX 1: GEA -> GEA
			OFFSET 0
			0% -100%
			SW AILE D/R

			I hope that this is all that has to be done.

TimHansen: LEA 5H new airframe config

2010-12-28T15:34:15Z

LEA 5H new airframe config

← Older revision		Revision as of 09:34, 28 December 2010
Line 7:		Line 7:
	== uBlox GPS 5H ==		== uBlox GPS 5H ==
	It is necessary to modify the airframe config-file ("-DGPS_USE_LATLONG") [[Airframe_Configuration#GPS]]		It is necessary to modify the airframe config-file ("-DGPS_USE_LATLONG") [[Airframe_Configuration#GPS]]

			In the newer Airframe Config File this has to be:
			<define name="GPS_USE_LATLONG"/>
			in the firmware section otherwise you might get the error:
			Invalid_argument("Latlong.of_utm")



	== Sound Output ==		== Sound Output ==

TimHansen: Telemetry Mode FBW

2010-12-28T15:08:15Z

Telemetry Mode FBW

← Older revision		Revision as of 09:08, 28 December 2010
Line 4:		Line 4:

	after that: [[Airframe_Configuration#Infrared]]		after that: [[Airframe_Configuration#Infrared]]


	== uBlox GPS 5H ==		== uBlox GPS 5H ==

	It is necessary to modify the airframe config-file ("-DGPS_USE_LATLONG") [[Airframe_Configuration#GPS]]		It is necessary to modify the airframe config-file ("-DGPS_USE_LATLONG") [[Airframe_Configuration#GPS]]

Line 13:		Line 11:
	I just found out, that the Ground Control Station can "speak" some messages. This is very useful for the battery low warnings:		I just found out, that the Ground Control Station can "speak" some messages. This is very useful for the battery low warnings:
	[[Speech]]		[[Speech]]

			== PPM Output ==
			To activate the PPM Messages in the new airframe config insert:
			<define name="TELEMETRY_MODE_FBW" value="1"/>
			to the firmware section.

TimHansen: Sound Output

2009-07-19T00:26:45Z

Sound Output

← Older revision		Revision as of 18:26, 18 July 2009
Line 9:		Line 9:

	It is necessary to modify the airframe config-file ("-DGPS_USE_LATLONG") [[Airframe_Configuration#GPS]]		It is necessary to modify the airframe config-file ("-DGPS_USE_LATLONG") [[Airframe_Configuration#GPS]]

			== Sound Output ==
			I just found out, that the Ground Control Station can "speak" some messages. This is very useful for the battery low warnings:
			[[Speech]]

TimHansen at 20:45, 18 July 2009

2009-07-18T20:45:33Z

← Older revision		Revision as of 14:45, 18 July 2009
Line 1:		Line 1:
	== IR Sensors connection Cable ==		== IR Sensors connection Cable ==

	Pay attention when connecting the ~~2 axis~~ IR-~~sensor~~: It's not allowed to exchange the ends of the cable. The pinout at the sensor board and the Tiny is different!		Pay attention when connecting the IR-sensors: It's not allowed to exchange the ends of the cable. The pinout at the sensor board and the Tiny is different!

	after that: [[Airframe_Configuration#Infrared]]		after that: [[Airframe_Configuration#Infrared]]

TimHansen: GPS 5H

2008-11-22T19:01:42Z

GPS 5H

← Older revision		Revision as of 13:01, 22 November 2008
Line 4:		Line 4:

	after that: [[Airframe_Configuration#Infrared]]		after that: [[Airframe_Configuration#Infrared]]


			== uBlox GPS 5H ==

			It is necessary to modify the airframe config-file ("-DGPS_USE_LATLONG") [[Airframe_Configuration#GPS]]

TimHansen: Link to [Airframe_Configuration#Infrared

2008-11-22T17:22:43Z

Link to [Airframe_Configuration#Infrared

← Older revision		Revision as of 11:22, 22 November 2008
Line 2:		Line 2:

	Pay attention when connecting the 2 axis IR-sensor: It's not allowed to exchange the ends of the cable. The pinout at the sensor board and the Tiny is different!		Pay attention when connecting the 2 axis IR-sensor: It's not allowed to exchange the ends of the cable. The pinout at the sensor board and the Tiny is different!

			after that: [[Airframe_Configuration#Infrared]]

TimHansen: IR Sensor Cable

2008-11-22T17:06:38Z

IR Sensor Cable

New page

== IR Sensors connection Cable ==

Pay attention when connecting the 2 axis IR-sensor: It's not allowed to exchange the ends of the cable. The pinout at the sensor board and the Tiny is different!