SUMO/install rc - Revision history

Martinmm: add degree indicator image for motor mount

2017-03-12T06:55:45Z

add degree indicator image for motor mount

← Older revision		Revision as of 00:55, 12 March 2017
Line 41:		Line 41:

	Mount the motor in the back of the aircraft. The downthrust should be around 1°, see manual.		Mount the motor in the back of the aircraft. The downthrust should be around 1°, see manual.

			[[Image:Sumo_degree_indicator.jpg\|290px]]

	[[Image:Funjet_motor.jpg\|600px]]		[[Image:Funjet_motor.jpg\|600px]]

Martinmm at 19:13, 10 April 2013

2013-04-10T19:13:43Z

← Older revision		Revision as of 13:13, 10 April 2013
Line 35:		Line 35:


	Add a male BEC cable for the Umarim power supply to the speed controller battery input connector. Attach the motor to the speed controller. Mount the speed controller at the back of the fuselage.		Add a male BEC cable for the Umarim power supply to the speed controller battery input connector and extend the total length to 42cm. Attach the motor to the speed controller. Mount the speed controller at the back of the fuselage.

	[[Image:Funjet_esc.jpg\|600px]]		[[Image:Funjet_esc.jpg\|600px]]

Martinmm at 18:39, 9 April 2013

2013-04-09T18:39:09Z

← Older revision		Revision as of 12:39, 9 April 2013
Line 24:		Line 24:

	Shopping list		Shopping list


	== Assembly ==		== Assembly ==
Line 32:		Line 33:

	[[Image:Funjet_servo.jpg\|600px]]		[[Image:Funjet_servo.jpg\|600px]]


	Add a male BEC cable for the Umarim power supply to the speed controller battery input connector. Attach the motor to the speed controller. Mount the speed controller at the back of the fuselage.		Add a male BEC cable for the Umarim power supply to the speed controller battery input connector. Attach the motor to the speed controller. Mount the speed controller at the back of the fuselage.

	[[Image:Funjet_esc.jpg\|600px]]		[[Image:Funjet_esc.jpg\|600px]]


	Mount the motor in the back of the aircraft. The downthrust should be around 1°, see manual.		Mount the motor in the back of the aircraft. The downthrust should be around 1°, see manual.

	[[Image:Funjet_motor.jpg\|600px]]		[[Image:Funjet_motor.jpg\|600px]]


	Install the propeller on the prop saver. Make sure you keep the rubber in a good condition. Replace them early.		Install the propeller on the prop saver. Make sure you keep the rubber in a good condition. Replace them early.
			Put black duct tape over the edge of the glass so that the glass fibres can not hurt. Add the same tape over the leading edge of the wing.

	[[Image:Funjet_prop.jpg\|600px]]		[[Image:Funjet_prop.jpg\|600px]]

Martinmm: inst

2013-04-09T18:33:25Z

inst

@@ Line 11: / Line 11: @@
 |-
 |2||Graupner DES-476 BB||Digital servos 11.5mm||Graupner|| ||Graupner #7915
 |-
 |1||Axi 2212/26 Gold Line||Brushless motor 920 RMP/V||Axi|| ||Axi #221226
 |-
-|1||Jeti Eco 25||Brushless speed controller 25A||Jeti|| ||
+|1||APC Slo-Flyer 9x6"|| || || ||
 |}
@@ Line 20: / Line 24: @@
 Shopping list

Martinmm: Created page with "NOTOC == What you need == {|border="1" cellspacing="0" style="text-align:center" width="80%" valign="top" |-style="background:LightYellow; color:black" !Qty!!Manufa…"

2013-03-17T23:20:16Z

Created page with "__NOTOC__ == What you need == {|border="1" cellspacing="0" style="text-align:center" width="80%" valign="top" |-style="background:LightYellow; color:black" !Qty!!Manufa…"

New page

__NOTOC__

== What you need ==


{|border="1" cellspacing="0" style="text-align:center" width="80%" valign="top"
|-style="background:LightYellow; color:black"
!Qty!!Manufacturer part number!!Description!!Manufacturer!!Digikey part number!!Other distributor
|-style="background:WhiteSmoke; color:black"
|colspan="6" align="left"|''RC electronics''
|-
|2||Graupner DES-476 BB||Digital servos 11.5mm||Graupner|| ||Graupner #7915
|-
|1||Axi 2212/26 Gold Line||Brushless motor 920 RMP/V||Axi|| ||Axi #221226
|-
|1||Jeti Eco 25||Brushless speed controller 25A||Jeti|| ||

|}


Shopping list

SUMO/install rc - Revision history

Martinmm: add degree indicator image for motor mount

Martinmm at 19:13, 10 April 2013

Martinmm at 18:39, 9 April 2013

Martinmm: inst

Martinmm: Created page with "__NOTOC__ == What you need == {|border="1" cellspacing="0" style="text-align:center" width="80%" valign="top" |-style="background:LightYellow; color:black" !Qty!!Manufa…"

Martinmm: Created page with "NOTOC == What you need == {|border="1" cellspacing="0" style="text-align:center" width="80%" valign="top" |-style="background:LightYellow; color:black" !Qty!!Manufa…"