SUMO/install electronics - Revision history

Martinmm: correct multi board orientation

2014-02-24T10:24:10Z

correct multi board orientation

← Older revision		Revision as of 04:24, 24 February 2014
Line 18:		Line 18:
	Fix the Multi board with four screws and and servo rubbers.		Fix the Multi board with four screws and and servo rubbers.

	[[Image:~~Multi_board_install~~.jpg\|600px]]		[[Image:Multi_board_install_corr.jpg\|600px]]

Martinmm: add link to prepare electronics

2013-12-12T15:28:41Z

add link to prepare electronics

← Older revision		Revision as of 09:28, 12 December 2013
Line 1:		Line 1:
			See [[SUMO/prepare_electronics\|Prepare Paparazzi electronics]] for a detailed description of where exactly the connectors/plugs go to.


	Glue the USB Mini-B board for the Umarim lite to the right side of the end of the battery compartment.		Glue the USB Mini-B board for the Umarim lite to the right side of the end of the battery compartment.

Martinmm: add GPS receiver

2013-12-12T15:16:34Z

add GPS receiver

← Older revision		Revision as of 09:16, 12 December 2013
Line 7:		Line 7:

	[[Image:Umarim_board_xbee.jpg\|600px]]		[[Image:Umarim_board_xbee.jpg\|600px]]


	Add a 3mm plywood board 41mm by 26mm one centimeter above the base of the fuselage. Drill holes to hold the Multi board before mounting. Install the Umarim lite with 1.6mm screws and servo rubbers in between.		Add a 3mm plywood board 41mm by 26mm one centimeter above the base of the fuselage. Drill holes to hold the Multi board before mounting. Install the Umarim lite with 1.6mm screws and servo rubbers in between.
Line 27:		Line 26:

	[[Image:Logger_shrink.jpg\|600px]]		[[Image:Logger_shrink.jpg\|600px]]

			Put the GPS receiver with the ceramic antenna upwards into the pocket under the front turtle deck (picture shows not-yet attached deck).

			[[Image:Funjet_gps_b.jpg\|600px]]

Martinmm at 20:00, 10 April 2013

2013-04-10T20:00:03Z

← Older revision		Revision as of 14:00, 10 April 2013
Line 32:		Line 32:

	[[Image:Mlx_install.jpg\|600px]]		[[Image:Mlx_install.jpg\|600px]]


			Insert the PT1000 temperature sensor into the ABS holder and fix it to the right wing.

			[[Image:Temperature_sensor_holder.jpg\|600px]]

			[[Image:Temperature_sensor_inside.jpg\|600px]]

			[[Image:Temperature_installed.jpg\|600px]]


			The same applies to the SHT75 humidity sensor on the left wing.

			[[Image:Humidity_sensor_holder.jpg\|600px]]

			[[Image:Humidity_sensor_inside.jpg\|600px]]

			[[Image:Humidity_installed.jpg\|600px]]


			Overview.

			[[Image:Funjet_sensors.jpg\|600px]]

Martinmm: Created page with "Glue the USB Mini-B board for the Umarim lite to the right side of the end of the battery compartment. 600px Install two 3mm plywood boards 41mm by 10…"

2013-04-10T18:37:07Z

Created page with "Glue the USB Mini-B board for the Umarim lite to the right side of the end of the battery compartment. 600px Install two 3mm plywood boards 41mm by 10…"

New page

Glue the USB Mini-B board for the Umarim lite to the right side of the end of the battery compartment.

[[Image:Funjet_usb.jpg|600px]]

Install two 3mm plywood boards 41mm by 10mm centered behind the fiber rod and aligned to the distance of the Umarim lite drill holes with CA. Fix the XBee pro with the Sparkfun board below the boards with Velcro.

[[Image:Umarim_board_xbee.jpg|600px]]

Add a 3mm plywood board 41mm by 26mm one centimeter above the base of the fuselage. Drill holes to hold the Multi board before mounting. Install the Umarim lite with 1.6mm screws and servo rubbers in between.

[[Image:Umarim_board_multi.jpg|600px]]

Fix the Multi board with four screws and and servo rubbers.

[[Image:Multi_board_install.jpg|600px]]

The logger holding 3mm plywood board is 41mm by 30mm and installed 5mm behind the Umarim lite at the same level.

[[Image:Logger_board.jpg|600px]]

Add a 10mm EPP separator between the autopilot and the motor compartment. Connect the logger to the Umarim, add the micro SD card holder and the USB Mini-B behind the separator. Fix the logger on the board with Velcro.

[[Image:Logger_shrink.jpg|600px]]

Glue the MLX90614 infrared thermometer into the 25mm x 20mm pocket. Seal the metal sensor with the EPP to make it watertight. Bring the connecting cable to the fuselage. Close the pocket with the original (colored) EPP.

[[Image:Mlx_install.jpg|600px]]