Martinmm: /* Result message */

2013-03-10T15:52:27Z

Result message

← Older revision		Revision as of 09:52, 10 March 2013
Line 101:		Line 101:

	Sample log file lines		Sample log file lines
	~~(none)~~		14.712 123 DPICCO_STATUS 10628 12005 32.44 20.45
			14.963 123 DPICCO_STATUS 10628 12005 32.44 20.45
			15.212 123 DPICCO_STATUS 10615 12005 32.4 20.45
			15.464 123 DPICCO_STATUS 10589 12005 32.32 20.45


	[[Category:User_Documentation]] [[Category:Modules]]		[[Category:User_Documentation]] [[Category:Modules]]

Martinmm: Created page with "NOTOC IST DigiPicco ==Overview== The IST DigiPicco is a relative humidity and digital temperature sensor. Adaption speed was ok at very low …"

2013-03-07T23:02:22Z

Created page with "__NOTOC__ thumb|right|IST DigiPicco ==Overview== The IST DigiPicco is a relative humidity and digital temperature sensor. Adaption speed was ok at very low …"

New page

__NOTOC__
[[Image:Dpicco.jpg|thumb|right|IST DigiPicco]]
==Overview==

The IST DigiPicco is a relative humidity and digital temperature sensor. Adaption speed was ok at very low temperatures and perfect in summer temperatures.

{|border="1"
|-valign="top"
||Module name||meteo/humid_dpicco
|-
|Sensor type
|humidity, temperature
|-
|Range (humidity)
| 0 .. 100 %RH
|-
|Range (temperature)
| -40°C .. +125°C
|-
|Resolution (humidity)
|? %RH
|-
|Resolution (temperature)
|?°C
|-
|Refresh rate
|4Hz
|-
|I2C address
|0xF0
|}

[http://www.ist-usadivision.com/objects/media/data-sheets/product/humidity/DigiPicco%20I2C.pdf Product data sheet]

==Hardware==
The sensor board can be directly interfaced to the autopilots I2C 3.3V interface

Supplier:

[http://uk.farnell.com/ist-innovative-sensor-technology/digipicco-tm-basic-i2c-g/sensor-humidity-module/dp/1778051 Farnell]

=== Wiring ===
{|border="1"
|-valign="top"
||'''Autopilot I2C pin'''||'''Autopilot I2C'''||'''DigiPicco'''||'''DigiPicco pin'''
|-
|1
|GND
|GND
|W8
|-
|2
| +5V
|Vcc+
|W10
|-
|3
|
|
|
|-
|4
|SDA
|SDA
|W4
|-
|5
|SCL
|SCL
|W3
|}

==Usage==

To use the humidity sensor add:
{{Box Code|conf/airframes/myplane.xml|
<source lang="xml">
<modules>
<load name="humid_dpicco.xml"/>
</modules>
</source>
}}

===Result message===

The raw data (humid/temp) and the converted result (fhumid/ftemp) is written to the log file. The message is automatically sent when new data is received, it does not have to be added to the telemetry file.
{{Box Code|conf/messages.xml|
<source lang="xml">
<message name="DPICCO_STATUS" id="91">
<field name="humid" type="uint16"/>
<field name="temp" type="uint16"/>
<field name="fhumid" type="float" unit="rel_hum" format="%.2f"/>
<field name="ftemp" type="float" unit="deg_celsius" format="%.2f"/>
</message>
</source>
}}

Sample log file lines
(none)

[[Category:User_Documentation]] [[Category:Modules]]

Module/IST DigiPicco - Revision history

Martinmm: /* Result message */

Martinmm: Created page with "__NOTOC__ IST DigiPicco ==Overview== The IST DigiPicco is a relative humidity and digital temperature sensor. Adaption speed was ok at very low …"

Martinmm: Created page with "NOTOC IST DigiPicco ==Overview== The IST DigiPicco is a relative humidity and digital temperature sensor. Adaption speed was ok at very low …"