User/LisaM

From PaparazziUAV
Jump to navigation Jump to search

Introduction

If you consider yourself a developer this autopilot board is for you. If you enjoy writing software and consider yourself an early adopter this hardware is for you. Have fun and see you on the paparazzi mailinglist, the wiki and the freenode irc channel

Lisa/M V1.0 top view
Lisa/M V1.0 bottom view
Lisa/M V1.0 top view
Lisa/M V1.0 bottom view

Features

Lisa/M is based on the 64 pins STM32F103RE processor featuring 64k of RAM and 512k of FLASH. All the pins are exposed, providing access to the complete set of the STM32 peripherals.


Overview

  • Single STM32 MCU
  • ? x Analog input channels
  • 1 x 3.3V TTL UART (5V tolerant)
  • 7 x PPM outputs
  • 1 x SPI bus
  • 1 x I2C bus
  • 1 x Micro USB (client)
  • power supply (input voltage range ?v → ?v)
  • ? x status LEDs with attached test point
  • grams (0. oz)
  • x mm (" x ")
  • 2 layers PCB design, components

Footprint

This autopilot is the smallest of it's class. The footprint is only 24mm by 40mm. It will fit in a small UAS very will. It comes with a pressure sensor built in for altitude measurements. there is a place for mounting the Aspirin IMU directly on board.

MCU

In brief, the STM32 features 3 USARTS, 2 SPI, 2 I2C, 1 CAN, a plethora of timers, ADCs and a generic DMA able to serve all of them. On the board, a number of the communication interfaces are level shifted with user selectable voltage to allow interfacing with all kind of peripherals.

IMU

The Lisa/M comes with Aspirin IMU mounted, for easy attitude estimation in the smallest package possible.

JTAG

Hardware Revision History

v1.00

Architecture

Pinout

Pins Name and Type are specified with respect to the Autopilot Board

LisaM V1 0 top labeled.png

Schematic

Electrical Connections to the Airborne Equipment

PCB

Gerber & Drill Files

Assembly

Components Layout

Mechanical drawing

LisaM V1 0 top mechanical.png

Bill Of Material

Setup

Connect Receivers

To be able to test your UAS a RC receiver comes in very handy.

PPM receiver

A modified RC receiver with full PWM out can be used to control the AP board from the ground.

Satellite Receiver

Connecting a 2.4 Spectrum compatible receiver

Lisa M V1 0 satellite receiver connection labeled.png

Power supply jumpers

LisaM V1 0 top jumpers and leds.pngLisaM V1 0 bottom jumpers.png

It is possible to reconfigure the electrical system on Lisa/M using the supply jumpers.

  • JP1 connects the servo power rail to V_IN rail.
  • JP2 connects the battery rail (used by default only for battery voltage measurement) to the V_IN rail.
  • JP3 bypasses the +5V voltage regulator and connects V_IN to the +5V rail.
  • JP4 connects the +5V rail to the VCC pin on the UART2 connector.
  • JP5 connects the +3V3 rail to the VCC pin on the UART2 connector.
  • JP6 connects the +5V rail to the VCC pin on the UART1 connector.
  • JP7 connects the +3V3 rail to the VCC pin on the UART1 connector.

PCB and assembled boards suppliers

For private companies and enthusiast Paparazzi hardware suppliers, see Get Hardware page.

Downloads

Source files

  • download LisaM v1.00 Eagle design (zip)

Gerber & Drill files

  • download gerber & drill files (zip)

Assembly files

  • download (pdf)
  • download (zipped .xls file)