Difference between revisions of "User/LisaM"

From PaparazziUAV
Jump to navigation Jump to search
m (redirect to correct page right away)
 
(66 intermediate revisions by 6 users not shown)
Line 1: Line 1:
== Introduction ==
#REDIRECT [[Lisa/M v2.0]]
 
If you consider yourself a developer this autopilot board is for you. If you enjoy writing software and consider yourself an early adopter this hardware is for you. Have fun and see you on the paparazzi mailinglist, the wiki and the freenode irc channel
 
[[Image:Lisa_M_V1_0_top_with_coin.jpg|thumb|Lisa/M V1.0 top view]]
[[Image:Lisa_M_V1_0_bottom_with_coin.jpg|thumb|Lisa/M V1.0 bottom view]]
[[Image:Lisa_M_V1_0_top.jpg|thumb|Lisa/M V1.0 top view]]
[[Image:Lisa_M_V1_0_bottom.jpg|thumb|Lisa/M V1.0 bottom view]]
 
== Features ==
 
Lisa/M is based on the 64 pins STM32F103RE processor featuring 64k of RAM and 512k of FLASH. All the pins are exposed, providing access to the complete set of the STM32 peripherals.
 
 
== Overview ==
 
* Single [http://www.st.com/stm32 STM32 MCU]
* ? x Analog input channels
* 1 x 3.3V TTL UART (5V tolerant)
* 7 x PPM outputs
* 1 x [http://en.wikipedia.org/wiki/Serial_Peripheral_Interface SPI] bus
* 1 x [http://en.wikipedia.org/wiki/I2c I<sup>2</sup>C] bus
* 1 x Micro USB (client)
* power supply (input voltage range ?v &rarr; ?v)
* ? x status LEDs with attached test point
*  grams (0. oz)
*  x mm (" x ")
* 2 layers PCB design,  components
 
=== Footprint ===
 
This autopilot is the smallest of it's class. The footprint is only 24mm by 40mm. It will fit in a small UAS very will. It comes with a pressure sensor built in for altitude measurements. there is a place for mounting the [http://paparazzi.enac.fr/wiki/AspirinIMU Aspirin IMU] directly on board.
 
=== MCU ===
 
In brief, the STM32 features 3 USARTS, 2 SPI, 2 I2C, 1 CAN, a plethora of timers, ADCs and a generic DMA able to serve all of them. On the board, a number of the communication interfaces are level shifted with user selectable voltage to allow interfacing with all kind of peripherals.
 
=== IMU ===
 
The Lisa/M comes with [http://paparazzi.enac.fr/wiki/AspirinIMU Aspirin IMU] mounted, for easy attitude estimation in the smallest package possible.
 
=== JTAG ===
 
== Hardware Revision History ==
 
v1.00
 
== Architecture ==
 
== Pinout ==
 
Pins Name and Type are specified with respect to the Autopilot Board
 
[[Image:LisaM_V1_0_top_labeled.png|700px]]
 
== Schematic ==
 
== Electrical Connections to the Airborne Equipment ==
 
== PCB ==
 
=== Gerber & Drill Files  ===
 
== Assembly ==
 
===Components Layout===
 
=== Mechanical drawing ===
 
[[Image:LisaM_V1_0_top_mechanical.png|500px]]
 
=== Bill Of Material ===
 
= Setup =
 
== Connect Receivers ==
 
To be able to test your UAS a RC receiver comes in very handy.
 
=== PPM receiver ===
 
A modified RC receiver with full PWM out can be used to control the AP board from the ground.
 
=== Satellite Receiver ===
 
Connecting a 2.4 Spectrum compatible receiver
 
[[Image:Lisa_M_V1_0_satellite_receiver_connection_labeled.png|500px]]
 
== Power supply jumpers ==
 
[[Image:LisaM_V1_0_top_jumpers_and_leds.png|500px]][[Image:LisaM_V1_0_bottom_jumpers.png|450px]]
 
It is possible to reconfigure the electrical system on Lisa/M using the supply jumpers.
 
* JP1 connects the servo power rail to V_IN rail.
* JP2 connects the battery rail (used by default only for battery voltage measurement) to the V_IN rail.
* JP3 bypasses the +5V voltage regulator and connects V_IN to the +5V rail.
* JP4 connects the +5V rail to the VCC pin on the UART2 connector.
* JP5 connects the +3V3 rail to the VCC pin on the UART2 connector.
* JP6 connects the +5V rail to the VCC pin on the UART1 connector.
* JP7 connects the +3V3 rail to the VCC pin on the UART1 connector.
 
[[Category:User_Documentation]] [[Category:Hardware]]
 
== PCB and assembled boards suppliers ==
 
For private companies and enthusiast Paparazzi hardware suppliers, see [[Get_Hardware|Get Hardware]] page.
 
== Downloads ==
 
'''Source files'''
:*download ''LisaM v1.00 Eagle design (zip)''
'''Gerber & Drill files'''
:*download '' gerber & drill files (zip)''
'''Assembly files'''
:*download ''(pdf)''
:*download '' (zipped .xls file)''

Latest revision as of 08:46, 16 December 2012

Redirect to: