Umarim Lite v2

From PaparazziUAV
Jump to navigation Jump to search
Umarim Lite v2 bottom side


Hardware Revision History

Version # Release Date Release Notes
v2 07/2012 Minor PCB modifications
v1 03/2012 Initial release of Umarim Lite


Features

  • NXP LPC2148 MCU based
  • 1 x Triple axis Digital Gyroscope (Invensense ITG-3200)
  • 1 x Triple axis Digital Accelerometer (Analog Devices ADXL345)
  • 6 x Servo PWM outputs
  • 1 x R/C receiver PPM frame input
  • 2 x UART (TTL 3.3V, 5V tolerant)
  • 2 x I2C bus
  • 1 x SPI bus
  • 1 x USB (client)
  • 4 x General Purpose I/O or Analog input channels (0V - 3.3V)
  • 5v / 1.5A switching power supply (input voltage range 5.5V min → 17.0v max)
  • 3.3v / 1A linear regulator
  • 2 x status LEDs
  • 8 grams (0,3 oz)
  • 53 x 25mm (2.1" x 0.98")
  • 4 layers PCB design / single side SMD components

Pinout

Pins Name and Type are specified with respect to the Autopilot Board

UmarimLite v2 pinout.png


SRV0/1/2/3/4/5
Pin # Name Type Description Color
1 GND PWR common ground Black
2 +5V PWR 5V Rail from autopilot Orange
3 SRVx OUT Servo signal (PWM) White


R/C
Pin # Name Type Description Color
1 GND PWR common ground Black
2 +5v PWR 5V Rail from autopilot Orange
3 PPM_IN IN PPM Stream from R/C Receiver (5V tolerant) White


SPI1
Pin # Name Type Description Color
1 GND PWR common ground Black
2 +3.3V PWR 3.3V Rail from autopilot Red
3 SSEL1 IN SSP Slave Select. Selects the SSP interface as a slave (SSEL1) Brown
4 MOSI1 I/O SPI1 Master Out Slave In. Data output from master / data input to slave Grey
5 MISO1 I/O SPI1 Master In Slave Out. Data input to master / data output from slave Green
6 DRDY1 IN External interrupt 0 input (EINT0) Purple
7 SCK1 I/O SPI1 Serial clock. Clock output from master or input to slave Yellow


AUX
Pin # Name Type Description Color
1 GND PWR common ground Black
2 +5V PWR 5V Rail from autopilot Orange
3 +3.3V PWR 3.3V Rail from autopilot Red
4 AUX1 I/O General Purpose I/O #1 or ADC Input ADC_0 (lpc AD1.5)
5 AUX2 I/O General Purpose I/O #2 or ADC Input ADC_1 (lpc AD1.4)
6 AUX3 I/O General Purpose I/O #3 or ADC Input ADC_2 (lpc AD1.3)
7 AUX4 I/O General Purpose I/O #4 or ADC Input ADC_3 (lpc AD1.2)


UART0
Pin # Name Type Description Color
1 GND PWR common ground Black
2 +5V PWR 5V Rail from autopilot Orange
3 +3.3V PWR 3.3V Rail from autopilot Red
4 RXD0 IN UART0 Serial Input (3.3V level, 5V Tolerant) Green
5 TXD0 OUT UART0 Serial Output (3.3V level) Blue


UART1
Pin # Name Type Description Color
1 GND PWR common ground Black
2 +5V PWR 5V Rail from autopilot Orange
3 +3.3V PWR 3.3V Rail from autopilot Red
4 RXD1 IN UART1 Serial Input (3.3V level, 5V Tolerant) Green
5 TXD1 OUT UART1 Serial Output (3.3V level) Blue


I2C0
Pin # Name Type Description Color
1 GND PWR common ground Black
2 +5V PWR 5V Rail from autopilot Orange
3 +3.3V PWR 3.3V Rail from autopilot Red
4 SDA0 Open Drain
I/O
I2C0 bus Serial DAta Brown
5 SCL0 Open Drain
I/O
I2C0 bus Serial CLock Blue


I2C1
Pin # Name Type Description Color
1 GND PWR common ground Black
2 +5V PWR 5V Rail from autopilot Orange
3 +3.3V PWR 3.3V Rail from autopilot Red
4 SDA1
BOOT
Open Drain
I/O
I2C1 bus Serial DAta
In-Circuit Serial Programming (ISP) enable (P0.14, +3.3v pullup) (Note)
Brown
5 SCL1 Open Drain
I/O
I2C1 bus Serial CLock Blue

Note: Holding this pin low for at least 3mS after a RESET (or power up) instructs the controller to enter programming mode.


USB
Pin # Name Type Description Color
1 GND PWR common ground Black
2 USB+ I/O USB bidirectional D+ line Green
3 USB- I/O USB bidirectional D- line White
4 VBUS IN Indicates the presence of USB bus power (P0.23) (5V level) Orange

Note: MiniUSB and Molex USB connectors are in parallel, only one can be connected at a time.


Schematic

Umarim V1.0 Schematic


Assembly

Components Layout


PCB and assembled boards suppliers

Check availability on Get Hardware page

Mechanical Dimensions

Umarim v1.0 Mechanical Dimensions


Paparazzi USB Bootloader Upload

Required components


Note1: It is advised to use FTDI USB-serial converter, as serial FTDI chips are by default working well in Linux.
The Paparazzi ground station software is configured to look for modems on FTDI ports by default.
This harness can also serve as a modem interface (after it's use in Bootloader uploading) if you plug it on Umarim's UART1 connector


Connection Diagram

Make up a wiring harness similar to the following

Umarim Lite v2 Paparazzi bootloader upload connections


Boot Sequence

LPC based autopilot boot sequence