Difference between revisions of "TWOG/add i2c1"
Jump to navigation
Jump to search
(Created page with "Category:Hardware == Add 2nd I2C port to Tiny/TWOG == It can be handy to have a second I2C port on the TWOG v1.00 or Tiny v2.11. This allows to separate flight sensitive se…") |
|||
| Line 1: | Line 1: | ||
[[Category:Hardware]] | [[Category:Hardware]] | ||
= Add 2nd I2C port to TWOG/Tiny = | |||
It can be handy to have a second I2C port on the TWOG v1.00 or Tiny v2.11. This allows to separate flight sensitive sensors (e.g. IMU) from payload sensors. | It can be handy to have a second I2C port on the TWOG v1.00 or Tiny v2.11. This allows to separate flight sensitive sensors (e.g. IMU) from payload sensors. | ||
| Line 17: | Line 17: | ||
The original I2C/J6 is i2c0 and ADC2/J8 becomes i2c1. | The original I2C/J6 is i2c0 and ADC2/J8 becomes i2c1. | ||
==Modification== | ==Modification TWOG/Tiny== | ||
[[Image:Twog_v100_i2c1_mod.jpg]] | [[Image:Twog_v100_i2c1_mod.jpg]] | ||
= Add 2nd I2C port to Tiny = | |||
On the Tiny Download/J7 can also be modified to have I2C. | |||
cut the trace between J7_LPC_TXD0 and the IC5/LPC2148 | |||
add a 10k pull-up resistor to J7_+3.3v | |||
connect other side of the new 10k to J7_LPC_TXD0 | |||
connect J7_LPC_TXD0 with J2_CTS (SCL1) | |||
secure the thin wire with small dots of hot glue | |||
The original I2C/J6 is i2c0 and Download/J7 becomes i2c1 (J7_LPC_TXD0 = SCL1, J7_BOOT = SDA1). | |||
==Modification Tiny== | |||
[[Image:Tiny_v2-1_i2c1_mod.jpg]] | |||
Revision as of 12:53, 9 May 2012
Add 2nd I2C port to TWOG/Tiny
It can be handy to have a second I2C port on the TWOG v1.00 or Tiny v2.11. This allows to separate flight sensitive sensors (e.g. IMU) from payload sensors.
ADC2/J8 can easily be modified to have the same pinout as the original I2C/J6 port.
remove R12 replace R13 with a 10k resistor cut the trace between R13 and R15 connect the (then) open end of R13 with 3.3V at R17 connect J8_IN_ADC_6 with J7_BOOT (SDA1) connect J8_IN_ADC_5 with J2_CTS (SCL1) secure the thin wire with small dots of hot glue
The original I2C/J6 is i2c0 and ADC2/J8 becomes i2c1.
Modification TWOG/Tiny
Add 2nd I2C port to Tiny
On the Tiny Download/J7 can also be modified to have I2C.
cut the trace between J7_LPC_TXD0 and the IC5/LPC2148 add a 10k pull-up resistor to J7_+3.3v connect other side of the new 10k to J7_LPC_TXD0 connect J7_LPC_TXD0 with J2_CTS (SCL1) secure the thin wire with small dots of hot glue
The original I2C/J6 is i2c0 and Download/J7 becomes i2c1 (J7_LPC_TXD0 = SCL1, J7_BOOT = SDA1).
Modification Tiny
