Difference between revisions of "Module/Melexis MLX90614"

From PaparazziUAV
Jump to: navigation, search
m (One-time configuration)
m (One-time configuration: Added the missing "_" in IR_MLX_ONE_TIME_CONFIG directive between the words TIME and CONFIG)
Line 93: Line 93:
 
<source lang="xml">
 
<source lang="xml">
 
     <load name="ir_mlx.xml">
 
     <load name="ir_mlx.xml">
       <define name="IR_MLX_ONE_TIME CONFIG" value="1"/>
+
       <define name="IR_MLX_ONE_TIME_CONFIG" value="1"/>
 
     </load>
 
     </load>
 
</source>
 
</source>

Revision as of 13:26, 8 May 2013

Melexis MLX90614 on breakout board
Melexis MLX90614 bottom view

Overview

The Melexis MLX90614 is a digital infrared radiation sensor. It is used to measure earths surface temperature when flying at low altitudes. It measures both the object (earth) temperature and the case (sensor) temperature.

Module name meteo/ir_mlx
Sensor type temperature
Range (object) -70°C .. +380°C
Resolution 0.02°C
Refresh rate 8Hz
I2C address 0x06

MLX90614 product homepage


Hardware

The board does have a 3.3V I2C interface.

Breakout board: Paparazzi hardware repo

Supplier:

Future Electronics

Sparkfun

Wiring

Autopilot I2C pin Autopilot I2C MLX90614 MLX90614 pin
1 GND Vss 4
2
3 +3.3V Vdd 3
4 SDA SDA 2
5 SCL SCL 1


Usage

To use the infrared radiation sensor:

File: conf/airframes/myplane.xml
  <modules>
    <load name="ir_mlx.xml"/>
  </modules>


One-time configuration

(currently only available in the master branch)

The I2C address is stored in internal flash memory and is usually randomly set. To set it to a useful value (0x06) put the below define only once while setting your equipment up.

File: conf/airframes/myplane.xml
    <load name="ir_mlx.xml">
      <define name="IR_MLX_ONE_TIME_CONFIG" value="1"/>
    </load>

Result message

Both the sensor case temperature and infrared object temperature are measured. The raw data (itemp_case/_obj) and the converted result (temp_case/_obj) is written to the log file. The message is automatically sent when new data is received, it does not have to be added to the telemetry file.

File: conf/messages.xml
  <message name="MLX_STATUS" id="85">
   <field name="itemp_case" type="uint16"/>
   <field name="temp_case" type="float" unit="deg_celsius" format="%.2f"/>
   <field name="itemp_obj" type="uint16"/>
   <field name="temp_obj" type="float" unit="deg_celsius" format="%.2f"/>
  </message>

The sensors 64bit serial number is read out at init and transmitted every 30 seconds.

File: conf/messages.xml
  <message name="MLX_SERIAL" id="113">
    <field name="serial0" type="uint32"/>
    <field name="serial1" type="uint32"/>
  </message>


Sample log file lines

6.000 123 MLX_SERIAL -1468333052 -931101532
6.518 123 MLX_STATUS 14703 20.91 14702 20.89
6.634 123 MLX_STATUS 14703 20.91 14702 20.89
6.750 123 MLX_STATUS 14704 20.93 14705 20.95
6.878 123 MLX_STATUS 14703 20.91 14702 20.89

NOTES

If flying at higher altitudes the infrared radiation from the in-between water vapor is also measured.