Difference between revisions of "Graupner HOTT setup"

From PaparazziUAV
Jump to navigation Jump to search
(output types)
m (minor details)
Line 3: Line 3:
=Overview=
=Overview=
Required steps for a brand new set:
Required steps for a brand new set:
# update the firmware on transmitter and receiver
# Update the firmware on transmitter and receiver
# bind transmitter and receiver
# Binding
# set up thr transmitter
# Set up the transmitter
# set up the receiver to PPM sum stream
# Set up the receiver to PPM sum stream


=Update the Software=
=Update the Software=
When the transmitter is switches on the firmware version is diplayed short.<br/>
When the transmitter is switches ON the firmware version is diplayed short.<br/>
Check if the transmitter uses obsolete firmware version in comparison to [http://www.graupner.de/en/supportdetail/6b8778a9-fcdc-4b4a-8189-c964760f0b99 the current firmware version available]
Check if the transmitter uses obsolete firmware version in comparison to [http://www.graupner.de/en/supportdetail/6b8778a9-fcdc-4b4a-8189-c964760f0b99 the current firmware version available]


Line 19: Line 19:
If a brand new Micro SD card is used, the folder architecture is not present:
If a brand new Micro SD card is used, the folder architecture is not present:
# put Micro SD card into transmitter
# put Micro SD card into transmitter
# switch on transmitter
# switch ON transmitter
# after transmitter bootet completely the Folder architecture has been created, switch off
# after transmitter bootet completely the Folder architecture has been created, switch OFF
# remove Micro SD card
# remove Micro SD card


Line 26: Line 26:
# connect Micro SD card with pc
# connect Micro SD card with pc
# copy the firmware file in the Firmware folder and the language file in the VoiceFile folder
# copy the firmware file in the Firmware folder and the language file in the VoiceFile folder
# put Micro SD card into transmitter and switch it on
# put Micro SD card into transmitter and switch it ON
# switch off HF
# switch OFF HF
# press up and down button on the left pannel simultaneously and SET on the right to get into the hidden mode
# press up and down button on the left pannel simultaneously and SET on the right to get into the hidden mode
# firmware update, choose the appropiate file
# firmware update, choose the appropiate file
Line 61: Line 61:


===Factory Reset===
===Factory Reset===
# press and hold SET
# press and hold SET
# connect receiver with power
# connect receiver with power
Line 67: Line 68:


=Binding=
=Binding=
# switch on the transmitter, turn off HF
 
# switch transmitter ON, turn OFF HF
# connect receiver with power
# connect receiver with power
# go into the main menue via SET
# go into the main menue via SET
Line 78: Line 80:
## GR-24 press and hold SET until a red and green LED light together
## GR-24 press and hold SET until a red and green LED light together
# within 3 seconds, press SET on transmitter at rx bind
# within 3 seconds, press SET on transmitter at rx bind
=Set up Transmitter=


=Set up PPM sum stream=
=Set up PPM sum stream=
# connect receiver with power
# connect receiver with power
# press ESC on transmitter for 2 sec, this will open the Telemtry menue
# press ESC on transmitter for 2 sec, this will open the Telemtry menue
Line 85: Line 91:
# right to RX SERVO TEST
# right to RX SERVO TEST
# down to CH OUT TYPE
# down to CH OUT TYPE
# change this from ONCE (standard output) to SUMD FS (sum stream output)
# change this from ONCE (standard output) to SUMD FS (sum stream output with Fail Safe values i case of signal loss)
# confirm with SET
# confirm with SET
# the number right of SUMD FS indicated how much channels are used, change them to the number of channels the transmitter provides
# the number right of SUMD FS indicated how much channels are used, change them to the number of channels the transmitter provides


(e.g. GR-12 can output up to 12 channels in SUMO mode)
(e.g. GR-12 can output up to 12 channels in SUMD mode)
=Set up Transmitter=
 
=Hardware Tips & Tricks=
'''Output Type'''<br/>
The receiver offers following output types:
 
* ONCE
Standard setting, for analog servos, all servos are driven after each other.<br/>
The cycle lengh is 20mS (doesn't matter what Period and RX Servo is set to), GR-24 is set to 30mS.
 
* SAME
For digital servos, they are driven in quater blocks (4 servos are driven at once, than the next 4 and so on).<br/>
Set cycle time to 10mS if only digital servos are used, if analog are used set cycle time to 20mS.
 
* SUMI
Sum stream in, is needed if 2 receivers are used in satelite mode for redundancy.
 
* SUMO
Sum stream output for satelite mode.
 
* SUMD
Digital sum stream output
 
** HD last received valie will be held
** FS Fail Safe values will send
** OF no signals will be send
The Last two letters indicate the handling if the connection to the transmitter is lost
 
'''Signal Lengh'''<br/>
Servo signal Lengh can be changed in the Telemetry menue at the RX Srvo Test page.<br/>
Standard min: 1000µS<br/>
Standard max: 1000µS


=Documentation=
=Documentation=
[http://www.graupner.de/en/supportdetail/40d3f611-16da-4c33-a749-f3e7553c0e8c Graupner HOTT software]<br/>
[http://www.graupner.de/en/supportdetail/40d3f611-16da-4c33-a749-f3e7553c0e8c Graupner HOTT software]<br/>
[http://www.mikrokopter.de/ucwiki/MX-20#Summensignal| Mikrokoper MX-20]
[http://www.mikrokopter.de/ucwiki/en/MX-20| Mikrokoper MX-20]


[[Category:User_Documentation]]
[[Category:User_Documentation]]

Revision as of 14:16, 21 November 2013

These instructions show all steps needed to use a Graupner HOTT 2.4 GHz transmitter/receiver system with PPM sum stream.

Overview

Required steps for a brand new set:

  1. Update the firmware on transmitter and receiver
  2. Binding
  3. Set up the transmitter
  4. Set up the receiver to PPM sum stream

Update the Software

When the transmitter is switches ON the firmware version is diplayed short.
Check if the transmitter uses obsolete firmware version in comparison to the current firmware version available

The page the firmware can be downloaded also provides special information for the version, some require special handling

Update the Transmitter

Update via Micro SD card

This is available with firmware version v1.7xx and above for mx-12 and mx-16.

If a brand new Micro SD card is used, the folder architecture is not present:

  1. put Micro SD card into transmitter
  2. switch ON transmitter
  3. after transmitter bootet completely the Folder architecture has been created, switch OFF
  4. remove Micro SD card

Update:

  1. connect Micro SD card with pc
  2. copy the firmware file in the Firmware folder and the language file in the VoiceFile folder
  3. put Micro SD card into transmitter and switch it ON
  4. switch OFF HF
  5. press up and down button on the left pannel simultaneously and SET on the right to get into the hidden mode
  6. firmware update, choose the appropiate file
  7. repeat this step with the voice file

If this fails, try the update with pc.


Update via PC

  1. connect the transmitter with pc, switch on, install the Sil Labs CP210x USB UART driver if needed
  2. open the Firmware Upgrade studio
  3. Menue -> Port Select choose the COM port (Silicon Labs CP210x USB to UART Bride)
  4. Controller Menu -> Transmitter -> Firmware Upgrade
  5. File Browse -> choose downloaded firmware file
  6. Download Start -> accept the RF OFF warning message
  7. Controller Menue -> Transmitter -> Voice download
  8. File Browse -> choose downloaded vioce file


Update the Receiver

  1. download the firmware
  2. open the Firmware Upgrade Studio
  3. connect the receiver on the telemetry port via the GM-Genius adapter to the pc
  4. Controller Menue -> Device -> HOTT Receiver
  5. File Browse -> choose the downloaded firmware file
  6. Program
  7. press and hold SET
  8. connect the receiver to a power supply
  9. release SET
  10. factory Reset

Factory Reset

  1. press and hold SET
  2. connect receiver with power
  3. wait 5 sec
  4. release SET

Binding

  1. switch transmitter ON, turn OFF HF
  2. connect receiver with power
  3. go into the main menue via SET
  4. got to rs bind
  5. got to Module
  6. if there is already a receiver bound , press SET to delete the binding
  7. differs on receiver:
    1. GR-12 press and hold SET
    2. GR-16 press and hold SET until a red and green LED light together
    3. GR-24 press and hold SET until a red and green LED light together
  8. within 3 seconds, press SET on transmitter at rx bind

Set up Transmitter

Set up PPM sum stream

  1. connect receiver with power
  2. press ESC on transmitter for 2 sec, this will open the Telemtry menue
  3. go to Settings & Data View
  4. right to RX SERVO TEST
  5. down to CH OUT TYPE
  6. change this from ONCE (standard output) to SUMD FS (sum stream output with Fail Safe values i case of signal loss)
  7. confirm with SET
  8. the number right of SUMD FS indicated how much channels are used, change them to the number of channels the transmitter provides

(e.g. GR-12 can output up to 12 channels in SUMD mode)

Documentation

Graupner HOTT software
Mikrokoper MX-20

Retrieved from "http://wiki.paparazziuav.org/w/index.php?title=Graupner_HOTT_setup&oldid=16334"